Panasonic Digital Imaging System For Copier Dp 6000 Operating Instructions

2-4 Changing the Paper Tray Size29
Loading Paper
2
 Press Settings/Meter Check on the control panel.
             
Select Tools Mode.
Enter the Access Number of the System Administrator by using
the keypad and select Confirm.
Each input digit is represented by an asterisk.
 Select Paper Tray Attributes.
 Select Paper Sizes.
If you made a mistake while entering
the Access Number, press the Clear
C button to clear and re-enter.
The factory default Access Number
is 11111.
Changing the Access Number of the...

2-4 Changing the Paper Tray Size30
Loading Paper
2
Select the tray that you have changed by using the
buttons. Then select Change Settings.
For example, select Tray 3.
Select the desired preset paper size.
If the preset paper size is measured in inches, select Inch
Size. Then select the desired paper size.
Select Save once and Close twice.
Select Exit Tools.
The paper size of the selected tray is changed.
The tray can also be selected
directly by touching its button on the
display.
As Tray 1 and Tray 6...

2-4 Changing the Paper Tray Size31
Loading Paper
2
Tray 6 (High Capacity Feeder) is
optional.
This section explains the procedures for changing the paper sizes to be
loaded in Tray 6 (High Capacity Feeder).
Paper sizes that can be loaded are B5
, A4, and 8.5 x 11.
Procedure
Pull Tray 6 (High Capacity
Feeder) out slowly until it
stops.
When pulling out a
paper tray, do it
slowly. If pulled out
with too much force,
the tray can hit and
injure your knees.
Remove any paper still in
the tray.
Turn the screw...

2-4 Changing the Paper Tray Size32
Loading Paper
2
When the paper size is
changed to B5
, remove
the Horizontal Guide from
the right side of the tray.
Insert the Horizontal Guide
into the (B5) slot and
fasten the screw.
Place the paper against
the bottom-right corner of
the tray.
Paste the new Paper Size
Label on the front of the
tray.
Push the tray in slowly until
it stops. When pushing
back Tray 6 (High Capacity
Feeder), do not place your
hand on the front of the
tray. You may hurt your
fingers if you...

3-1 Documents .................................................................. 34
3-2 Loading Documents .................................................... 36
3
Loading Documents 

3-1 Documents34
Loading Documents
3
Documents
Place document on the Document Glass or load it in the Duplex Automatic
Document Feeder (DADF).
Place the following types of documents on the Document Glass. They will
cause jams when loaded in the DADF.
Documents that are relatively heavy, for example, brochures and booklets
Torn, wrinkled, paste-up, punched-hole, folded or curled documents
Paper-clipped or stapled documents
Documents with carbon on the reverse side
Highly transparent documents such as...

3-1 Documents35
Loading Documents
3
The largest document size that can be placed on the Document Glass is
shown below.  There is no limit on the smallest size.
When using the Document Glass, the paper sizes, which can be
automatically detected by the machine are A6, B6, B6
, A5, A5, 5.5 x
8.5, 5.5 x 8.5
, B5, B5, A4, A4, 8.5 x 11, 8.5 x 11, 8.5 x 14 (or
8.5 x 13), B4, 8K (267 x 388 mm), A3, and 11 x 17.
If you make copies with the document cover open, avoid
looking directly at the copy lamp. Direct eye...

3-2  Loading Documents36
Loading Documents
3
Loading Documents
Load the documents in the DADF or place it on the Document Glass.
The DADF lets you load a stack of documents for feeding to the scanner
one sheet at a time, and output them after scanning. 50 sheets can be
loaded each time, thus saving time of loading documents manually.
    Procedure
Align the lead edges of your documents.
Remove any paper clips, staples and Post-it¨ Notes before making copies.
Load documents face up
(side one should face...

3-2  Loading Documents37
Loading Documents
3
    Procedure
Open the document cover.
Place the document face
down and align it with the
upper-left corner of the
Document Glass.
Close the document cover.
When copying a
thick document, do not
use excessive force to
press it against the
Document Glass. The
glass may break and
cause injuries.
    Document Orientation
When a feature such as, 2 Sided, Multi-Up (N Up), Image Shift, Edge
Erase/Copy All, Repeat Image, or Stapling/Punching (optional) is
selected,...

3-2  Loading Documents38
Loading Documents
3
The message Size Mismatch may be displayed if you have pressed the
Start button after placing your document on the Document Glass and
selecting the copy function.
Size here refers to the image size that is calculated based on the document
size detected by the machine and the specified ratio.
The Size Mismatch message screen will be displayed if the machine is
unable to detect the document size and the image size does not fit the
selected paper size. This may...