Panasonic Digital Imaging System For Copier Dp 6000 Operating Instructions

4-8  Stapling (Stapling)69
Basic Features
4
Select the corresponding document orientation of the original
loaded, and select Save.
Select Head to Top or Head to Left.
Confirm the settings at the lower left side of the screen and
select Save.
Select other features if necessary.
Enter the required number of sets by using the keypad and
press Start.
The copies are collated set by set, stapled, and delivered to finisher Tray 2.
You can remove the copies from finisher Tray 2 after all the
copies are delivered...

4-9  Punching Holes (Punching)70
Basic Features
4
Punching Holes
(Punching)
When the Finisher (optional) is installed, copies can be made and output
with punched holes.  Paper sizes that can be punched and the positions of
holes are as follows.
Paper sizes that can be punched and the positions of holes
B5, A4, 8.5 x 11 paper: Holes are punched at the long edge.
B4, A3, 11 x 17 paper: Holes are punched at the short edge.
For B5, A4, 8.5 x 11 size, holes cannot be punched on the short edge.
For 
B4, A3, 11...

4-9  Punching Holes (Punching)71
Basic Features
4
Procedure
 On the Basic Features screen, select Output/Finishing.
 Select Collated/Finishing.
 Then select On for Punching.
Select Top Side, Left Side, or Right Side.
For example, select Left Side (left button).
The screen on the right has the Tray
6 (High Capacity Feeder), and
Finisher installed.
Output/Finishing can also be
selected on the Features Menu
screen.
Select Cancel to cancel the settings. 

4-9  Punching Holes (Punching)72
Basic Features
4
Select Cancel to cancel the settings.
Some features cannot be selected
together with this feature. See
Appendix B: Possible Combinations
of Features
 for details.
To stop the copy job, press Stop on
the control panel or touch Stop
displayed on the screen. See 
4-11:
Stopping a Copy Job
 for details.
If the Punching feature is Off in Step
3, copies will be output to Finisher
Tray 1.
Do not remove any paper from
Finisher Tray 2 while copies are
being...

4-10  Resetting the Copy Sets and Feature Settings to Their Defaults73
Basic Features
4
Resetting the Copy Sets and
Feature Settings to Their Defaults
If you made a mistake while entering the value for the number of sets to be
copied, you can select the Clear C button from the Control Panel to clear and
then re-enter the value. This button can also be used to clear settings of the
previous copy job.
Select Clear All on the Control Panel to clear all settings and return them to
their defaults.
Resetting...

4-11  Stopping a Copy Job74
Basic Features
4
Stopping a Copy Job
If there is an Auto Start copy job, the
Auto indicator light on the top left of
the Start button will be lit.
If the copy in progress screen is
displayed, select Stop on the screen
to halt the copy operation.
To stop a copy job, pressing Stop will stop the job temporarily.  Press Clear
C or Clear All after that to stop the copy job.
Procedure
 Press Stop.
The current copy job is stopped temporarily. The screen below is displayed.  A
waiting...

4-12  Interrupting a Copy Job75
Basic Features
4
You can interrupt a copy job that is in progress for an urgent job. Once the
urgent job is done, the copier will resume the interrupted copy job.
Interrupting a copy job cannot be carried out under the conditions below:
¥When documents are being scanned in the DADF.
¥When documents are being scanned on the Document Glass up to
selection of End Job.
Procedure
Press Interrupt.
The indicator light at the top left of the Interrupt button lights up indicating...

4-13  Programming Ahead76
Basic Features
4
Programming Ahead
The Program Ahead feature allows you to make selections for, and perform
scanning of jobs in advance, while preceding jobs are being output.
Procedure
While the screen below is being displayed, select Program
Ahead.
 Make selections for the next job, load your documents and
press Start to begin scanning.
The job will start automatically after the preceding job has been completed.
 When Number of Documents is 51 and Above
The number of documents...

5-1 Overview of Added Features ...................................... 78
5-2 Adjusting Copy Density (Lighter/Darker) .................... 80
5-3 Making a Copy According to Original Type
(Original Type) ............................................................ 82
5-4 Copying Several Documents onto One Copy
(Multi-Up (N Up)) ......................................................... 84
5-5 Loading Mixed Size Originals
(Mixed Size Originals) .................................................  87
5-6...

5-1  Overview of Added Features78
Added Features
5
Overview of Added Features
Paper Supply
Select this option to select the paper size.
4.2: Selecting a Paper Tray (Paper Supply)
Reduce/Enlarge
Select this option to reduce/enlarge a copy image.
4.3: Reducing/Enlarging (Reduce/Enlarge)
Lighter/Darker
Select this option to adjust the density of a copy.
5.2: Adjusting Copy Density (Lighter/Darker)
Document Type
Select this option to make a copy that matches the
document type.
5-3: Making a Copy according to...