Panasonic Digital Imaging System For Copier Dp 6000 Operating Instructions

2-1 What Paper to Use19
Loading Paper
2
The special media mentioned on the
right cannot be used for 2-Sided
copying.
Do not use paper with glue or tape
on it.
Special Media cannot be loaded in
Trays 1 and 6 (High Capacity
Feeder) (optional).
Load perforated paper with the holes
toward the back of the tray.
Types of Special Media
The types of media for the respective trays are as shown below.
            Tray
Trays 2 to 4
Tray 5 (Bypass)Special Media
Transparencies, perforated paper (30-hole)...

2-2 Storing and Handling Paper20
Loading Paper
2
Storing and Handling Paper
Observe the following when storing paper:
¥Always store paper in a cabinet or at a place with low humidity. Damp
paper may cause jams or affect the image quality.
¥Always re-pack unused paper, preferably with desiccant.
¥Always store paper on a flat surface to prevent bending or curling.
Observe the following when handling paper:
¥Do not combine and load paper left-over from different reams into a tray.
¥Do not use folded or...

2-3  Loading Paper21
2
Loading Paper
During a copy job, paper can be
added to a tray not selected for the
current job that is in progress.
Loading Paper
The following screen will appear when paper runs out during a copy job.
Add paper according to the displayed instructions.  After adding the paper,
you can resume the copy job by pressing the Start button.
This section will show you how to add paper to Trays 1 to 4, Tray 5 (Bypass),
and Tray 6 (High Capacity Feeder).
Add paper to Trays 1 to 4 according...

2-3  Loading Paper22
2
Loading Paper
Push the tray in slowly
until it stops.
The message, Ready to copy.
Press Start to continue or press C
button to cancel the job. appears
on the display once you have
properly replenished the tray. 

2-3  Loading Paper23
2
Loading Paper
Load paper with the side to
be copied facing up and
inserting them till they
touch the back of the tray.
Make sure the edges of paper
towards you are aligned.
Move the Paper Guide to
touch the paper.
Tray 5 (Bypass) under Paper
Supply of the Basic Features
screen becomes selectable.
Do not place things other than
media on Tray 5 (Bypass). Also, do
not make copies while holding the
edge of the paper. The wrong paper
size may be detected leading to
paper jams.
Make sure...

2-3  Loading Paper24
2
Loading Paper
Loading Paper in Tray 6 (High Capacity Feeder) (optional)
Tray 6 (High Capacity Feeder) is
optional.
The capacity of Tray 6 (High
Capacity Feeder) (optional) is 3600
sheets.
Do not load paper above the MAX fill
line.
Load paper in Tray 6 (High Capacity Feeder) (optional) by following the
procedures below.
Procedure
Pull the tray out slowly until
it stops.
When pulling out a
paper tray, do it
slowly. If pulled out
with too much force,
the tray can hit and
injure your...

2-4 Changing the Paper Tray Size25
2
Follow the procedures shown below to change the size of Tray 1 in order to 
load paper stock of the desired size. 
For changing paper size A5
5.5 x 8.5, you have to do it via the Tools
Mode screen.
Procedure
Pull Tray 1 out until it 
stops.
When pulling out a 
paper tray, do it
slowly. If pulled out 
with too much force, 
the tray can hit and
injure your knees.
Remove any paper still in 
the tray.
Pinch and hold the release 
on the Lever as shown in 
the diagram. Then...

2-4 Changing the Paper Tray Size26
Loading Paper
2
Place paper stock of the
desired size against the
bottom-right corner of the
tray.
Pinch and hold the release
on the Lever again and
push the Lever forward
until it touches the edge of
the paper.
Paste the new Paper Size
Label on the front of the
tray.
Push Tray 1 in slowly until
it stops.
After changing from A55.5 X 8.5Ó,
there is a need to adjust settings in
Tools Mode screen. See 
Original/
Paper Size Sensing 
of 6.1: List of
Custom Preset Functions
. 

2-4 Changing the Paper Tray Size27
Loading Paper
2
Changing the Size of Trays 2 to 4
Request assistance from your System Administrator if you need to change
the size of Trays 2 to 4. Your System Administrator can follow the
procedures shown below to make the changes.
Procedure
Pull out the tray that you
want to change until it
stops.
When pulling out a
paper tray, do it
slowly. If pulled out
with too much force,
the tray can hit and
injure your knees.
Remove any paper still in
the tray.
Use a screwdriver...

2-4 Changing the Paper Tray Size28
Loading Paper
2
Place paper stock of the
desired size against the
bottom-right corner of the
tray.
Adjust the Paper Guides
according to the size of the
paper.
Remove the paper from
the tray and use a
screwdriver to fasten the
screws as shown in the
diagram.
Check that the Paper Guides are
locked at the holes with the screws
tightened. Then re-load the paper.
Paste the new Paper Size
Label on the front of the
tray.
Push the tray in slowly until
it stops.
Refer to the...