Panasonic Digital Imaging System For Copier Dp 6000 Operating Instructions

7-4  Stapler Faults189
Troubleshooting
7
Stapler Faults
This section explains the methods used to resolve stapling problems at the
Finisher (optional).  Follow the procedures on the following page to
troubleshoot problems such as faulty stapler and bent staples.
Contact your local authorized Panasonic service representative if the
staples are stapled on the copies in the manner as shown in the diagrams
below.
Contact your local authorized
Panasonic service representative if
the problems could not be...

7-4  Stapler Faults190
Troubleshooting
7
Procedure
Open the Front Door of the
Finisher.
Press the Orange Lever as
shown in the diagram and
pull out the Staple
Cartridge.
Open the cover of the
staple cartridge as shown
in the diagram and remove
the jammed staples.
When removing
jammed staples, take
care not to injure
your fingers.
If the staples could not be
removed, push in the
direction of the arrow to
remove the staples.
Contact your local authorized
Panasonic service representative if
the problems...

7-4  Stapler Faults191
Troubleshooting
7
Push the Staple Cartridge
in until the Orange Lever
returns to its original
position.
Close the Front Door of the
Finisher. 

This page is intentionally left blank. 

8-1 Cleaning the Copier .................................................... 194
8-2 Consumables .............................................................. 197
8-3 Increasing the Toner Level .......................................... 198
8-4 Replacing the Toner Cartridge .................................... 200
8-5 Replacing the Drum Cartridge .................................... 203
8-6 Replacing the Staple Cartridge ................................... 206
8-7 Emptying the Punch Scrap Container...

8-1  Cleaning the Copier194
Daily Care
8
Procedure
Lift the DADF slowly.
DADF will be stationary if fully
open.
Use a cloth made of soft
material, and moistened
with mild detergent.
Clean the Document Glass.
Clean the Document Cover.
Clean the DADF
Scanning Glass.
Cleaning the Copier
In order that clean copies can be made each time, you are recommended to
clean the following areas of the machine once a month.
¥ Document Cover/Document Glass/DADF Scanning Glass
¥ DADF Film/Roller sections
The Document...

8-1  Cleaning the Copier195
Daily Care
8
Use a dry cloth made of soft material to wipe.
Put the DADF slowly back
in place.
Procedure
Lift the Release Latch at
the center of the DADF
and open the Left Cover
completely.
Cover will be stationary
when fully open.
Lift the Lever with the
Green Seal to open the
inner cover.
Use a moistened and soft
cloth to clean the rollers
(total 18).  Clean them by
gently turning the rollers
with the cloth.
Cleaning the DADF Film/Roller Sections
If the film and roller...

8-1  Cleaning the Copier196
Daily Care
8
Do not press hard on the film as the
film section is very delicate.
Clean the rollers by turning them.
Close the Inner Cover.
Then close the Left Cover
of the DADF until you hear
a click sound.
Lift the DADF slowly.
Use a moistened and soft
cloth to clean the film
section and the roller
section (total 8).
Use a dry cloth made of
soft material to wipe.
Put the DADF slowly back
in place. 

8-2  Consumables197
Daily Care
8
    Types of Consumables 
The following consumables are available for this machine.
Ensure that the following consumables are used as this machine has
been developed according to the strictest regulations.
Use Panasonic-recommended consumables as non-
recommended ones may affect quality and performance of the
machine.
    Handling Consumables 
Do not place the boxes of consumables vertically.
Open the consumables only when you need to use them.  Do not store
them in the...

8-3  Increasing the Toner Level198
Daily Care
8
Increasing the Toner Level
If you find that copies made are too light, you can increase the copy density
by adjusting the toner level. This feature can be used besides the Lighter/
Darker feature to adjust the copy density.  However, normally there is no
need to use this feature because the toner quantity of the developer unit is
automatically adjusted by the machine.
Procedure
Press Settings/Meter Check.
Select Toner Level Adjustment.
Select Start.
5-2:...