Panasonic Digital Color Imaging Systems For Function Parameters Dp C354 Operating Instructions

							61
 Chapter 4    Fax/Email Settings
Memo 
						

							62
 Chapter 4    Fax/Email Settings
Example : LDAP Ser ver
To search an Email Address or a Fax Number on LDAP Server, the following user parameter settings 
are required.
Set the above items according to the descriptions below.
zFor details about LDAP search, refer to Searching for a Destination in the Operating Instructions (For 
Facsimile and Internet Fax) on the provided CD-ROM.
zLDAP can be setup in one sequence of procedure at “04 Network Settings” of General Setting Key Operator 
Mode. (see page 12)
LDAP Server Name (User parameter 15)
This setting is required only when “29 DNS Server Address” in General Settings is set to “Ye s”.
When the setting is “No”, set “16 LDAP Server IP” (see page 64).
1Press the Function key.
2Select “Fax/Email Settings”.
3Select “04 Key Operator Mode”.
4Enter the password (8-digit), and then 
select “OK”.
5Select “00 User Parameters”.
LDAP Server Name User parameter 15: LDAP Server Name
LDAP Server IP User parameter 16: LDAP Server IP
LDAP User Name User parameter 17: LDAP User Name
LDAP Password User parameter 18: LDAP Password
LDAP Search Base User parameter 19: LDAP Search Base 
						

							63
 Chapter 4    Fax/Email Settings
6Select “10-19”.
7Select .
8Select “15 LDAP Server Name”.
9Enter the LDAP Server Name (up to 
60 characters), and then select “OK”.
10Select “Off” or “On” and then select 
“OK”.
11Enter the Port Number (up to 5 digits), 
and then select “OK”.
zAdvance to 17 LDAP User Name, 18 LDAP 
Password, 19 LDAP Search Base (see 
page 66). 
						

							64
 Chapter 4    Fax/Email Settings
LDAP Server IP (User parameter 16)
This setting is required only when “29 DNS Server Address” in General Settings is set to “No”.
When the setting is “Ye s” set “15 LDAP Server Name” (see page 62).
1Press the Function key.
2Select “Fax/Email Settings”.
3Select “04 Key Operator Mode”.
4Enter the password (8-digit), and then 
select “OK”.
5Select “00 User Parameters”.
6Select “10-19”.
7Select . 
						

							65
 Chapter 4    Fax/Email Settings
8Select “16 LDAP Server IP”.
9Enter the LDAP Server IP Address (3-
digit x 4), and then select “OK”.
10Select “Off” or “On” and then select 
“OK”.
11Enter the Port Number (up to 5 digits), 
and then select “OK”.
zAdvance to “17 LDAP User Name”, “18 
LDAP Password”, “19 LDAP Search 
Base”.  
						

							66
 Chapter 4    Fax/Email Settings
LDAP User Name 
LDAP Password 
LDAP Search Base 
(User parameters 17, 18 and 19)
1Select “17 LDAP User Name”, “18 
LDAP Password”, and “19 LDAP 
Search Base”.
2Enter LDAP User name (up to 40 
characters), Password (up to 10 
characters) and Search Base (up to 60 
characters), and then select “OK”.
(Ex: LDAP Search Base screen) 
3Select “Close”.
zAfter setting up the function(s), press the 
Reset key to return the machine to the initial 
screen of the current active mode. 
						

							67
 Chapter 4    Fax/Email Settings
Memo 
						

							68
 Chapter 4    Fax/Email Settings
Example : Receive to Memor y
Receive to Memory secures all received originals by storing them into memory.
To print the original(s) received in memory, the Key Operator must enter the correct password.
The procedure of setting Receive to Memory is described below.
For memory reception, refer to Receive to Memory in the Operating Instructions (For Facsimile and Internet 
Fax) on the provided CD-ROM.
1Press the Function key.
2Select “Fax/Email Settings”.
3Select “04 Key Operator Mode”.
4Enter the password (8-digit), and then 
select “OK”.
5Select “01 Fax Parameters”.
6Select  (7 times).
zFax Parameters can be directly selected 
using a keypad for quick operation. If a 
Parameter No. is known, enter the desired 
Parameter No. with a keypad, and then 
press the Start key.
Ex:In step 6, enter “37” with a keypad, and 
press the “Start” key to select “37 
Receive to Memory”. 
						

							69
 Chapter 4    Fax/Email Settings
7Select “37 Receive to Memory”.
8Enter the Identification Code (4-digit), 
and then select “OK”.
(Ex: 1234)
zIf you have made an input error, select 
“Clear” on the screen to delete all 
characters at a time.
9Select “Close”.
zAfter setting up the function(s), press the 
Reset key to return the machine to the initial 
screen of the current active mode. 
						

							70
 Chapter 4    Fax/Email Settings
Example : Password-Transmit / Password-Receive
Password-Transmit : Send the original only when the recipient password matches the sender’s 
password.
Password-Receive : Receive the original only when the sender’s password matches the recipient 
password.
For setting the Password-Transmit / Password-Receive, set “43 Password-Transmit” or “44 
Password-Receive” to “On” and follow the procedure described below.
For password-transmit, refer to Password Communication in the Operating Instructions (For Facsimile and 
Internet Fax) on the provided CD-ROM.
For password-receive, refer to Convenient Reception Features in the Operating Instructions (For Facsimile and 
Internet Fax) on the provided CD-ROM.
1Press the Function key.
2Select “Fax/Email Settings”.
3Select “04 Key Operator Mode”.
4Enter the password (8-digit), and then 
select “OK”.
5Select “01 Fax Parameters”.