Panasonic Digital Color Imaging Systems For Copier Dp C354 Operating Instructions

							41
 Chapter 2    More Menus Features
Copying 2-Sided original(s) Onto two separate sheets
2-Sided original(s) can be copied, and separated into 1-Sided pages.
1Select “2-Sided / Original->Copy”, 
and then select “2 -> 1”.
zTo display this screen, refer to steps 1 to 3 of 
Basic Operation for the 2-Sided Copy 
Mode (see page 40).
2Select the bind position, and then 
select “OK”.
zFor the following procedure, refer to steps 5 
to 6 of Basic Operation for the 2-Sided 
Copy Mode (see page 40).
Long Edge:
Copies both sides of the 
original, facing them in the 
same direction.
Short Edge:
Copies both sides of the 
original facing them in the 
opposite direction. 
						

							42
 Chapter 2    More Menus Features
Copying Facing Page Original to Two Separate Sheets
Two facing pages or a 11 x 17 size original can be copied, and separated into 1-Sided sheets.
1Select “2-Sided / Original->Copy”, 
and then select “2 Page”.
zTo display this screen, refer to steps 1 to 3 of 
Basic Operation for the 2-Sided Copy 
Mode (see page 40).
zWhen “Multi-Size Feed” is selected, “2 
Page” cannot be selected.
2Select a page order of original.
3Select a copy layout, and then select 
“OK”.
zFor the following procedure, refer to steps 5 
to 6 of Basic Operation for the 2-Sided 
Copy Mode (see page 40).
The left page of the facing original 
is copied first.
The right page of the facing original 
is copied first.
The first through last page are 
copied.
The first page and beyond are 
copied, but the last page is not 
copied.
The first page is not copied, but the 
rest and including the last page are 
copied.
The first and the last page are not 
copied. 
						

							43
 Chapter 2    More Menus Features
From 1-Sided Originals to 2-Sided Copies using Saddle Stitch 
(Booklet)
zThe 2-Sided original cannot be copied into a booklet.
zOriginals should be placed on the ADF. (5.5 x 8.5 or 8.5 x 11 size is only available, up to 40 originals)
zSaddle stitch binding is possible only when the optional 1-Bin Saddle Finisher (DA-FS325) is installed.
Ledger (11 x 17), and Letter-R (8.5 x 11) are the only applicable paper sizes.
zThe standard setting for the copy size is the reduced size, however, the setting can be changed to a “original 
size”. Refer to Copier Settings in the Operating Instructions (For Function Parameters) on the provided CD-
ROM.
zWhen the Fold Position is not matched with center position of the copies, set the binding margin. Refer to 
General Settings (For Key Operator) in the Operating Instructions (For Function Parameters) on the provided 
CD-ROM.
zStamping can be combined with the Booklet For Copying with Stamping, refer to Copying with Stamping (see 
page 61-69).
1Select “2-Sided / Original->Copy”, 
and then select “Booklet”.
zTo display this screen, refer to steps 1 to 3 of 
Basic Operation for the 2-Sided Copy 
Mode (see page 40).
2Select a bind position.
3Select the cover page type if 
necessary.
1Select “Cover”.
Select when binding the left 
side, or the top side of the 
page.
Select when binding the 
right side, or the bottom 
side of the page.
Continue on the next page... 
						

							44
 Chapter 2    More Menus Features
2Select a cover type.
zWhen “Blank” is selected as the cover type, 
up to 36 originals can be placed on the ADF.
3Select “Cover” to select a paper.
zWhen changing paper other than the cover, 
press the Copy key on the Control Panel. If 
the paper of desired size is available on the 
tray, the display changes.
Select a paper size from the display.
4Select “OK” to exit the cover settings.
5Select “OK”.
zFor the following procedure, refer to steps 5 
to 6 of Basic Operation for the 2-Sided 
Copy Mode (see page 40).
zWhen the Fold Position does not match with 
the center position of the copies, set the 
binding margin. Refer to General Settings 
in the Operating Instructions (For Function 
Parameters) on the provided CD-ROM.
zThe stapled copies are delivered to the 
saddle tray of the 1-bin saddle finisher as 
shown below.BlankNot copied on the cover.
CopyCopied on the cover.
Staple position
Saddle tray 
						

							45
 Chapter 2    More Menus Features
Copying Mixed Size Originals from the ADF
Use this function when copying mixed size originals (8.5 x 11 and 11 x 17, or 8.5 x 11 and Legal) 
using with the ADF, original size can be detected automatically then can be copied to the same size, or 
one specified size.
zWhen copying in 2-Sided mode.
zIf no copy size is specified, the original is copied to its original size. If the copy size is specified, the original is 
copied automatically enlarged, or reduced in accordance with the specified size.
zOnly when specifying the same copy size, 2-Sided copying is possible by setting “2-Sided”.
zOnly when specifying the same copy size (8.5 x 11 only), the copies can be rotated, and printed as a booklet, 
or as a unit of specified number of pages by setting “Rotate-Sort” or “Rotate-Group”.
1Select “2-Sided / Original->Copy”, 
and then select “Multi-Size Feed”.
zTo display this screen, refer to steps 1 to 3 of 
Basic Operation for the 2-Sided Copy 
Mode (see page 40).
2Select an orientation, and then select 
“OK”.
Full Size Reduction
8.5 x 11-R (Letter-R)
8.5 x 14 (Legal)8.5 x 11-R (Letter-R)
11 x 17 (Ledger) 8.5 x 11 (Letter)
8.5 x 11-R (Letter-R)
Ex: Original Size (Standard Setting)Ex: Specified Size
8.5 x 11-R and Legal
8.5 x 11 and 11 x 178.5 x 11-R and Legal
8.5 x 11 and 11 x 178.5 x 11-R
8.5 x 11
Continue on the next page... 
						

							46
 Chapter 2    More Menus Features
3When copying the same paper size, 
touch “Basic Menu”, and then select a 
desired copy size with copy size 
button.
zFor the following procedure, refer to steps 5 
to 6 of Basic Operation for the 2-Sided 
Copy Mode (see page 40).
When all originals are 
vertically long 
Ex:
When the smaller original is 
vertically long, and the 
larger original is horizontally 
long
Ex:
When the smaller original is 
horizontally long, and the 
larger original is vertically 
long
Ex:
When all originals are 
horizontally long
Ex:
ABCABC
ABCABC
ABCABC
ABCABC
Ex:Combination of Letter (Portrait layout), and 
Ledger (Landscape layout) originals
Copy Images (1 -> 2 copy mode)
Bind Position is SHORT EDGE
Ledger
(Landscape
layout) Letter
(Portrait)
Copy size is 
not set.Copy size is 
set to Letter.
Letter
(Portrait)Blank
Ledger
(Landscape
layout)Letter*1
(Landscape
layout)
Letter
(Portrait) Face Face
BackBack
*1 Ledger size will be 
reduced to Letter size.
Ex:Combination of Letter (Portrait layout), and 
(Portrait layout) originals
Copy Images (1 -> 2 copy mode)
Bind Position is SHORT EDGE
Legal
(Portrait)Letter
(Portrait)
Copy size is 
not set.Copy size is 
set to Letter.
Face Face
Legal
(Portrait
layout)Letter
(Landscape
layout)
Blank Letter
(Landscape
layout)
Letter*2
(Landscape
layout)
*2 Legal size will be 
reduced to Letter size.
Back Back 
						

							47
 Chapter 2    More Menus Features
Copying Special Originals (Thin Paper, etc.) from the ADF
„SADF
This mode adds a 5 second delay to allow another original to be placed on the ADF. Special originals 
(like thin paper, etc.) can be fed from the ADF, and copied continuously using the SADF Mode. 
1Place one original (minimum 50 g/m2) 
on the ADF. 
2Press the Copy key if the machine is 
set to other function mode.
3Select “More Menus”.
4Select “2-Sided / Original->Copy”, 
and then select “Job Build and 
SADF”.
5Enter the desired number of copies.
6Press the Start key.
7Place the next original within 5 sec. of 
last ejected original(s). 
8After the last page is scanned, select 
“No” in the confirmation screen. 
						

							48
 Chapter 2    More Menus Features
„Job Build
This is useful, when copying multiple sets of originals that exceed the maximum capacity of the ADF of 
85 sheets (20 lb). (See the Example below)
Ex: To make 5 sets of sorted copies of 100-sheet of originals.
(a) Place the first 85 sheets of originals on the ADF.
(b) Select “2-Sided / Original->Copy” Copy menu, and select Job “Job Build and SADF”.
(c) Select “Sort / Finish” menu, and select the desired Sorting/Finishing end result.
(d) Press the Start key.
(e) After scanning the first 85 sheets, you can place the remaining 15 sheets of originals on the ADF 
within 5 second to continue copying without interrupting the cycle.
Or if you do nothing, the machine will display “Another original? / Yes or No”.
(f) Place the remaining 15 sheets of originals on the ADF tray, and select “Ye s”.
(g) After scanning the remaining 15 sheets, “Another original? / Yes or No” will display, select “No” 
to start the printing process.
zOriginal should be placed on the ADF.
zUp to 999 sheets of the originals can be scanned in one job.
The maximum capacity of the scanned data can be reached less than 999 sheets of the originals depending on 
the type of sheets being scanned. 
If the memory becomes full during scanning, follow the instructions on the Display.
85 1
100
1
100 86
Originals:85 sheets 
Originals: Remaining 15 sheets 1st and 2nd Scanning Data are 
combined into one job.
5 sets of 100-sheet sorted 
copies are printed 
						

							49
 Chapter 2    More Menus Features
Memo 
						

							50
 Chapter 2    More Menus Features
Sort Mode
The original can be copied, printed, and sorted in a specified number of sets.
• Optional Finisher is not installed. 
Refer to the Operating Instructions (For Basic Functions).
• Optional Finisher is installed. 
Shift-Sort, Shift-Group and Staple mode are available.
• Optional Punch Unit is installed
Punch mode is available.
zThe maximum number of pages to staple are as follows:
For 1-Bin Finisher
8.5 x 11: 30 sheets, Legal / 11 x 17: 20 sheets
For 1-Bin Saddle Stitch Finisher
8.5 x 11: 50 sheets, Legal / 11 x 17: 20 sheets
Saddle-Stitch:
8.5 x 11 (Letter-R), Legal, 11 x 17: 10 sets (6-10 sheets) / 20 sets (2-5 sheets)
1Place original(s).
zRefer to Placing Originals (Copy) in the 
Operating Instructions (For Basic 
Operations) of provided booklet.
2Press the Copy key if the machine is 
set to other function mode.
3Select “More Menus”.
4Select “Sort / Finish”, and then select 
a sort mode.
zWhen the “Staple-Sort” or “Punch” is 
selected, refer to next page. Shift-Sort Shift-Group Staple-Sort Punch