Panasonic Digital Camera Dmc Zs60 Owners Manual For Advanced Features

							61
Basics
Touch screen (Touch operations)
Touch screen of this unit is capacitive. Touch the panel directly with your bare finger.
TouchTo touch and release the touch screen. Be sure to touch 
the center of the desired icon.
DragTo touch and slide your finger across the touch screen. 
This can also be used to forward or rewind a picture during 
playback, etc.
Pinch (spread/pinch)On the touch screen, spread (pinch out) your 2 fingers to 
zoom in, and pinch (pinch in) your 2 fingers to zoom out.
Enabling/disabling the touch operation
 →  [Custom] → [Touch Settings]
[Touch Screen]All touch operations. When set to [OFF], only button and dial operations\
 
can be used.
[ON] / [OFF]
[Touch Tab] Operation to display the touch icons by touching tabs such as [
  ] 
displayed on the right of the screen.
[ON] / [OFF]
[
Touch AF] Operation to optimize the focus or both the focus and brightness for a 
touched subject.
[AF] (→156) / [AF+AE] (→162) / [OFF]
[Touch Pad AF] Operation to move the AF area by touching the monitor when the 
viewfinder is in use. 
(→161)
[EXACT] / [OFFSET] / [OFF] 
SQW0547              
						

							62
Basics
Touch screen (Touch operations)
 ●Touch the screen with the clean and dry finger. ●If you use a commercially available monitor protection sheet, please fol\
low the instructions that 
accompany the sheet. (Some monitor protection sheets may impair visibil\
ity or operability.)
 ●Do not press on the monitor with hard pointed tips, such as ballpoint pe\
ns. ●Do not press the touch screen with your fingernails. ●Clean the monitor with a soft, dry cloth if there are fingerprints or ot\
her kinds of dirt on it. ●Do not scratch or press the monitor too hard. ●The touch screen may not function normally in the following cases. • When touched by a gloved hand • When the touch screen is wet • When touched by multiple hands or fingers at the same time 
SQW0547     
						

							63
Basics
Touch screen (Touch operations)
Touching the screen and recording (Touch Shutter function)
Recording mode: 
This function enables you to focus and record still pictures simply by t\
ouching the 
subjects that appear on the screen.
1Touch [  ]
2Touch [  ] • The icon changes to [  ] and you can now proceed with touch 
shutter recording.
3Touch the subject you want to record • To release the touch shutter function → Touch [  ].
 ●If shooting with the touch shutter fails, the AF area turns red and disappears. ●Measurement of brightness is performed on the spot touched when the [Metering Mode] (→183) is 
set to [  ]. At the edge of the screen, the metering may be affected by the brightness around the 
touched location. 
SQW0547                      
						

							64
Basics
Touch screen (Touch operations)
Easily Optimizing the Brightness for a Specified Area  
([Touch AE])
Recording mode: 
You can easily optimize the brightness for a touched position. When the f\
ace of the 
subject appears dark, you can brighten the screen according to the brightness of the face.
1Touch [  ]
2Touch [  ] • The setting screen for the brightness optimization position is displayed.
 • [Metering Mode

] is set to [
  ], which is used exclusively for the 
[T
ouch AE].
3Touch the subject you want to optimize the brightness 
for
 • Touching [Reset] will bring the brightness optimization position  back to the center .
SetSet
ResetReset
4Touch [Set]
 ■Canceling the [ Touch AE] function
Touch [
  ] • [Metering Mode] returns to the original setting, and the brightness optimization posit\
ion is  canceled.
 ●This function is not available in the following cases: • When using the Digital Zoom • When [High Speed V

ideo] is set
 • When [4K Live Cropping

] is set
 • When [T

ouch AF] in [Touch Settings] of the [Custom] menu has been set to [AF+AE] (→61) 
SQW0547                   
						

							65
Basics
Setting the menu
You can use the menu to set camera and recording functions, operate playb\
ack functions, 
and perform other operations.
In this Owner’s Manual, steps for setting a menu item are described as follows:
Example:  To change the [Quality] setting from [  ] to [  ] in the [Rec] menu
 →  [Rec] → [Quality] → [  ]
How to set the menu
Menu settings can be made either by button or touch operation.
1Press [MENU/SET] to bring up the menuZS100
ZS60
[Rec]
(→379)You can perform settings for the aspect ratio, number of pixels, 4K 
Photo, etc.
[Motion Picture]
(→380)You can select the recording format and picture quality and other 
settings.
[Custom]
(→381)Operation of the unit, such as displaying of the screen and button 
operations, can be set up according to your preferences. Also, it is 
possible to register the modified settings.
[Setup]
(→382)You can perform settings that make usage more convenient, such 
as the changing the clock settings and beep volume. You can also 
perform Wi-Fi function-related settings.
[Playback]
(→382)You can specify picture protection, cropping, print settings, and other 
settings for pictures you have taken. 
SQW0547     
						

							66
Basics
Setting the menu
 ■Switching menu type
Press 
Menu type
Press   to select a tab such as [  ] •ZS100Items can also be selected by rotating the rear dial. •ZS60Items can also be selected by rotating the control dial.Press [MENU/SET]
With touch screen operations
Touch a tab, such as [
  ]
2Press   to select the menu item and press 
[MENU/SET]
 •ZS100The menu item can also be selected by rotating the rear 
dial.
 •ZS60The menu item can also be selected by rotating the 
control dial.
 • You can also switch to the next page by pressing [

DISP.] 
button or rotating the zoom lever.
With touch screen operations
Touch the menu item
 • You can switch to the next page by touching [  ]/[  ].
Page
Item
3Press   to select the setting and press [MENU/SET]
 •ZS100The setting can also be selected by rotating the rear dial. •ZS60The setting can also be selected by rotating the control 
dial.
 • The setting methods vary depending on the menu item.
With touch screen operations
Touch the setting to set
Selected setting
Settings 
SQW0547     
						

							67
Basics
Setting the menu
4Press [Q.MENU/] button repeatedly until the 
recording or playback screen reappears
 • During recording, the menu screen can also be exited by 
pressing the shutter button halfway.
With touch screen operations
Touch [
  ]
 ●When [Menu Resume] (→84) in the [Setup] menu is set to [ON], the screen 
displayed last after you selected the menu item will reappear.
It is set to [ON] at the time of purchase.
 ●When the [Menu Information] (→84) in the [Setup] menu is set to [ON], 
descriptions of the menu items and settings will appear on the menu scre\
en. 
SQW0547     
						

							68
Basics
Calling frequently-used menus instantly  (Quick Menu)
You can easily call some of the menu items and set them during recording.\
 • Some items or settings can not be selected depending on the mode or disp\
lay style the camera is in.
1Press [Q.MENU/] buttonZS100
ZS60
2ZS100
Rotate the rear dial to select a menu item, 
and press 
 or 
ZS60
Rotate the control dial to select a menu 
item, and press 
 or 
 • The menu item can also be selected by pressing  .
60p60p
3ZS100
Rotate the rear dial to select the setting
ZS60
Rotate the control dial to select the 
setting
 • The setting can also be selected with  .
60p60p
4Press [Q.MENU/] button to close the Quick menu 
SQW0547           
						

							69
Basics
Calling frequently-used menus instantly  (Quick Menu)
ZS100 Switching the method for setting Quick Menu items
 →  [Custom] → [Q.MENU]
[PRESET]:
 The default items can be set.
[CUST

OM]:
 The Quick Menu will consist of desired items (below).
ZS100 Change the Quick Menu to your preferred item
When [Q.MENU] in the [Custom] menu is set to [CUSTOM] (above), the Quick Menu can 
be changed as desired. Up to 15 items can be set to the Quick Menu.
1After pressing the [Q.MENU/] button, press  to 
select [  ], and press [MENU/SET]
2Press     to select the menu item in the top row 
and press [MENU/SET]
 • Items that are displayed in gray in the top row have already been 
set. Top row:  
Items that can be set
Bottom row: Set items
3Press   to select the empty space in the bottom row 
and press [MENU/SET]
 • You can also set the menu item by dragging it from the top row to 
the bottom row .
 • If there is no empty space in the bottom row, you can replace an existing item with a new select item by selecting the existing item.
 • To cancel the setting, move to the bottom row by pressing  and 
select an item to cancel, and then press [MENU/SET].
4Press [Q.MENU/] button • It will return to screen of step 1. Press [MENU/SET] to switch to the recording screen. 
SQW0547              
						

							70
Basics
You can assign frequently-used functions to particular buttons ([Fn1] - [Fn4]) or icons 
displayed on the screen ([Fn5] - [Fn9]).
 • Certain functions cannot be assigned to some function buttons. • The function assigned to the function button may not work in some modes \
or on some  display screens.
1Set the menu
 →  [Custom] → [Fn Button Set]
2Use   to select [Setting in REC mode] or [Setting in PLAY 
mode] and press [MENU/SET]
3Press   to select the function button 
you want to assign a function to and 
press [MENU/SET]
4Press   to select the function you want 
to assign and press [MENU/SET]
 • For details on the functions that can be assigned in 
[Setting in REC mode ], refer to (→71).
 • For details on the functions that can be assigned in 
[Setting in PLA

Y mode], refer to (→73).
 ■Rapidly assigning functions
The assignment screen displayed in Step 
4 above can be displayed by holding a 
function button ([Fn1] to [Fn4]) for 2 seconds.
Recording mode:  
The function assignment screen for [Setting in REC mode] is displayed
Playback mode:  
The function assignment screen for [Setting in PLAY mode] is displayed
 • In some cases the function assignment screen cannot be displayed dependi\
ng on the  mode or display screen
Assigning frequently used functions to the buttons  
(Function buttons) 
SQW0547