Panasonic Digital Camera Dmc Zs60 Owners Manual For Advanced Features

							301
Wi-FiWhat you can do with the Wi-Fi
® function
Operating the camera by connecting it to a smartphone/tablet 
(→305)
Taking pictures via a smartphone (remote recording)
Playing back pictures in the camera on a smartphone
Saving pictures in the camera to a smartphone
Sending pictures in the camera to social networking services
Writing the location information on pictures in the camera
Combining motion pictures recorded with Snap Movie according to your 
preference on a smartphone
Connect easily
You can easily set up a direct connection to your smartphone without ente\
ring a 
password.
Displaying still pictures on a TV  (→318)
Wireless printing  (→323)
Sending pictures to AV device (→324)
Still pictures and motion pictures can be sent to AV device in the home (home AV 
device).
Sending pictures to a PC  (→325)
Using WEB services (→327)
Through “LUMIX CLUB”, you can send still pictures and motion pictu\
res to social 
networking services, etc. You can receive still pictures and motion pictures on a PC or a 
smartphone/tablet using the Cloud Sync. Service.
 • Hereafter, this manual uses the term “smartphone” for both smartphones and \
tablets  unless it is necessary to distinguish between them. 
SQW0547   
						

							302
Wi-Fi
Wi-Fi Function
 ■Before Use
 • Complete the date and time settings in advance. (→42) • To use the Wi-Fi function on this unit, a wireless access point or a dest\
ination device 
equipped with the wireless LAN function is required.
 ■Lighting of the Wi-Fi connection lamp when the Wi-Fi function is in use
ZS100
ZS60
Lit:  When the Wi-Fi function is ON or connected 
by Wi-Fi
Blinking: 
 When sending picture data
 ■About the [Wi-Fi] button
In this Owner’s Manual, a function button to which [Wi-Fi] is assigned is referred to as 
the [Wi-Fi] button. (At the time of purchase, [Wi-Fi] is assigned to [Fn5] button.)
 • For details on the function button, refer to (→

70).
To start up the Wi-Fi function:
Touch [  ]
Touch [  ] 
SQW0547                
						

							303
Wi-Fi
Wi-Fi Function
 • Before a Wi-Fi connection is established, press the [Wi-Fi] button to perform the following operations:
 – The information (SSID) required for directly connecting  your smartphone to this unit is displayed.
 – You can select the following items by pressing [

DISP.] 
button.
[New Connection]
[Select a destination from History] (→342)
[Select a destination from Favorite] (→342)
SSID
 • You can also display the same menu by selecting  →  [Setup] → [ Wi-Fi] 
→ [Wi-Fi Function].
 • This manual provides information on the process when [New Connection] is  selected.
 • Pressing the [Wi-Fi] button during a Wi-Fi connection enables the follow\
ing operation.
[Terminate the Connection] Terminates the Wi-Fi connection.
[Change the Destination]
*1Terminates the Wi-Fi connection, and allows you to 
select a different Wi-Fi connection.
[Change Settings for Sending 
Images]
*2For details (→321).
[Register the Current Destination to 
Favorite]
*1Registering the current connection destination or the 
connection method, you can easily connect with the 
same connection method next time.
[Network Address] For details (→345).
*1   This item will not be displayed if you press  to send pictures to WEB services while the 
pictures are displayed  (→330).
*2   This item will not be displayed if the destination for [ Remote Shooting & View], [Playback on 
TV] or [Send Images Stored in the Camera] is set to [Printer]. 
SQW0547     
						

							304
Wi-Fi
Wi-Fi Function
 ■Describing method
When “select [Select a destination from History]”, etc. is 
described in a step, perform any of the following operations.With cursor button operations
Use cursor button to select [Select a destination from 
History] and press [MENU/SET].
With touch screen operations
Touch [Select a destination from History].
 ●Do not remove the memory card or battery or move to an area without any \
reception while 
sending images.
 ●The camera cannot be used to connect to a public wireless LAN connection\
. ●Use a IEEE802.11b, IEEE802.11g or IEEE802.11n compatible device when using a wireless 
access point.
 ●We recommend that you use a fully charged battery when you send pictures.\
 ●When sending images on a mobile network, high packet communication fees \
may be incurred 
depending on the details of your contract.
 ●Pictures may not be completely sent depending on radio wave conditions. \
If the connection is 
terminated while sending pictures, pictures with missing sections may be\
 sent.
 ●The monitor display may become distorted for an instant while connected \
to the service, however 
this will not affect the image being sent. 
SQW0547     
						

							305
Wi-Fi
Operating the camera by connecting it to a 
smartphone
You can remotely operate the camera using a smartphone.
The “Panasonic Image App” (hereafter “Image App”) must be installed on your 
smartphone.
Installing the smartphone/tablet app “Panasonic Image App”
For Android™ appsFor iOS apps
Supported OS Android 4.0 or later iOS 7.0 or later
Installation 
procedure
Connect your Android device to a 
network
Select “Google PlayTM Store”Enter “Panasonic Image App” or 
“LUMIX” to search for the app
Select “Panasonic Image App” and 
install it
 • The icon will be added to  the menu.
Connect the iOS device to the 
network
Select “App StoreSM”Enter “Panasonic Image App” or 
“LUMIX” to search for the app
Select “Panasonic Image App” and 
install it
 • The icon will be added to the menu.
 • Use the latest version. • Supported OS versions as of January 2016. Supported OS versions may be c\
hanged without prior notice.
 • The service may not be able to be used properly depending on the type of\
 smartphone being used.
For the latest information on the “Image App”, refer to the support site below

. 
http://panasonic.jp/support/global/cs/dsc/ (This site is available in E\
nglish only.)
 • When downloading the app on a mobile network, high packet communication \
fees may  be incurred depending on the details of your contract.
 • For details about the operating procedure, etc., refer to [Help] in the “Image App” menu. • If you connect the camera and smartphone over a Wi-Fi connection and run\
 “Image App”, [Help] may not be displayed in the “Image 

App” menu for some smartphones. In 
such a case, disconnect the Wi-Fi connection with the camera, connect th\
e camera to 
a cellular data line such as 3G and LTE, or the Internet to display [Help] in the “Image 
App” menu.
 • Some of the screens and information provided in this document may be dif\
ferent  depending on the supported operating system and “Image 

App” version. 
SQW0547     
						

							306
Wi-Fi
Operating the camera by connecting it to a smartphone
Connecting to a smartphone
You can easily establish a Wi-Fi connection on this unit without entering\
 a password on 
your smartphone.
Preparation
(On the camera) Set [Wi-Fi Password] to [OFF]. (→344)
(On your smartphone)  Install “Image App” in advance.  (→305)
[Wi-Fi Password] is set to [OFF] at the time of purchase. In [OFF] state, a third 
party can tap into the Wi-Fi transmission and steal transmitted data.
To set [Wi-Fi Password] to [ON], refer to (→308).
 • It may take some time for the operation to end after operating a smartph\
one.
1Select the menu on the camera
 →  [Setup] → [Wi-Fi ] → [Wi-Fi Function ] → [New Connection]  
→ [Remote Shooting & View]
 • The information required for directly connecting your smartphone  to this unit (SSID) is displayed.
 • You can also display the information by pressing [

Wi-Fi] button 
on the camera.
 • To change the connection method, refer to  (→

310).
SSID
2Operate the smartphone • The connection method differs depending on the smartphone used. 
SQW0547     
						

							307
Wi-Fi
Operating the camera by connecting it to a smartphone
 ■Using an iOS device
Turn on the Wi-Fi function in the setting 
menu of the smartphone
Select the SSID displayed on the screen of this unit
Return to the home screen and start “Image App” (→305) • When the connection confirmation screen appears on this unit, select [Ye s] and press  
[MENU/SET]. (Only when making a connection for the first time.)
 ■Using an Android device
Start  “Image App”  (→305) • If a message appears stating that a camera search is in progress, close \
the message.Select [  ]
Select the SSID displayed on this unit • When the connection confirmation screen appears on this unit, select [ Ye s] and press  
[MENU/SET]. (Only when making a connection for the first time.) 
SQW0547     
						

							308
Wi-Fi
Operating the camera by connecting it to a smartphone
Using a password to set up a connection
When [Wi-Fi Password] is set to [ON], you can strengthen security by usi\
ng manual input 
or a QR code for password authentication.
Preparation
(On the camera) Set [Wi-Fi Password] to [ON]. (→344)
(On your smartphone)  Install “Image App” in advance.  (→305)
1Select the menu on the camera
 →  [Setup] → [Wi-Fi] → [Wi-Fi Function ] → [New Connection]  
→ [Remote Shooting & View]
 • The information (QR Code, SSID and Password) required for  directly connecting your smartphone to this unit is displayed.
 • You can also display the information by pressing [

Wi-Fi] button 
on the camera.
 • Switching the connection method  (→310)
SSID and Password
QR Code
2Operate the smartphone • The connection method differs depending on the smartphone used. 
SQW0547     
						

							309
Wi-Fi
Operating the camera by connecting it to a smartphone
 ■Using an iOS device
 • When reading a QR Code to connect(Steps  to  are not necessary when reconnecting.)
Start  “Image App”  (→305)
Select [  ] → [OK]
Read the QR Code displayed on this unit with “Image App”
(When you press [MENU/SET] on the camera, the QR code is displayed in a\
n 
enlarged size.)
 • When the smartphone is connected to a wireless access point, it may take\
 time to display QR 
code.
Install the profile • The message is displayed in the Web browser . • If a passcode is required to unlock the smartphone, you will have to inp\
ut the passcode.Press the home button to close the Web browserTurn on the Wi-Fi function in the setting 
menu of the smartphone
Select the SSID displayed on the screen of this unit
Return to the home screen and start “Image App” (→305)
 • When connecting with SSID and password
Turn on the Wi-Fi function in the setting menu of the smartphoneSelect the SSID displayed on the screen of this unitEnter the password displayed on this unit (First time connecting only)\
Return to the home screen and start “Image App” (→305) 
SQW0547     
						

							310
Wi-Fi
Operating the camera by connecting it to a smartphone
 ■Using an Android device
 • When reading a QR Code to connect
Start  “Image App” (→305)
Select [  ]
Read the QR Code displayed on this unit with “Image App”
(When you press [MENU/SET] on the camera, the QR code is displayed in a\
n 
enlarged size.)
 • When the smartphone is connected to a wireless access point, it may take\
 time to display QR 
code.
 • When connecting with SSID and password
Start  “Image App”  (→305) • If a message appears stating that a camera search is in progress, close \
the message. Select  [  ]
Select the SSID displayed on this unitEnter the password displayed on this unit (First time connecting only)\
 • If you check the item to display the password, you can confirm the passw\
ord as you enter it.
Changing the connection method
To change the connection method, follow the steps below:
(When the connection is made using [Wi-Fi] in the [Setup] menu)Press [DISP.] button
(When the connection is made by pressing [Wi-Fi] button)
 → [DISP.] button → [ New Connection] → [Remote Shooting & View] → 
[DISP.] button
 ■When connecting with [Via Network]
(On the camera)
Select [Via Network] and press [MENU/SET] • Connect the camera to a wireless access point by following the  connection method  (→338)
.
(On your smartphone)Set Wi-Fi function to “ON”Select the wireless access point you connected to the 
camera, and set
Start  “Image App” (→305) 
SQW0547