Panasonic Digital Camera Dmc Gh4 Owners Manual

							271
10. Using the Wi-Fi/NFC Function
1Select the menu.
2Select [Via Network] or [Direct], and connect. (P292)
3Select a device you want to connect.
•When the connection is complete, the screen is displayed. To change the send setting, 
press [DISP.].  (P301)
4Select [Single Select] or [Multi Select].
•To change the setting or disconnect, press [Wi-Fi].  (P256)
Select and send the images ([Send Images Stored in the Camera])
> [New Connection]  > [Send Images Stored in the Camera]  > 
[Smartphone]
On your smartphone
When connecting with [Via Network]:
1 Turn on the Wi-Fi function.
2 Select the wireless access point you want to connect to, and set.
3 Start “ Image App ”.  (P258)
When connecting with [Wi-Fi Direct] or [WPS Connection] in [Direct]:
1 Start “ Image App ”.  (P258)
When connecting with [Manual Connection] in [Direct]:
1 Turn on the Wi-Fi function.
2 Select the SSID that matches the one displayed on the screen of this unit, and 
then enter the password.
3 Start “ Image App ”.  (P258)
[Single Select] setting
1 Select the picture.
2 Select [Set].
[Multi Select] setting
1 Select the picture. (repeat)
•
The setting is canceled when the picture is selected 
again.
2Select [OK].
•The number of pictures that can be sent by [Multi 
Select] is limited.
•Confirmation screen is displayed. It is executed when [Yes] is selected.
Wi-Fi
6HW
2. 
						

							10. Using the Wi-Fi/NFC Function
272
Displaying pictures on a TV
1Select the menu.
2Select [Via Network] or [Direct], and connect. (P292)3Select a device you want to connect.
•When the connection is established, the screen is displayed.
4Take or play back pictures on this unit.
•To change the setting or disconnect, press [Wi-Fi].  (P256)
•When a TV is connected to this unit, the TV screen may temporarily return to the status before 
the connection. Pictures are displayed again when you take or play back pictures.
•[Effect] and [Sound] of the Slide Show are disabled.
Not available in these cases:
•
Motion pictures cannot be played back.
•During the multi/calendar playback, pictures displayed on the screen of this unit are not 
displayed on TV.
You can display pictures on a TV that supports the 
Digital Media Renderer (DMR) function of the DLNA 
standard.
•
If you display pictures using the Wi-Fi function, they 
cannot be output in 4K resolution. To output them in 4K 
resolution, connect the camera and the TV with an HDMI 
micro cable.  (P325)
Preparations:
Set the TV to DLNA waiting mode.
•
Read the operating instructions for your TV.
> [New Connection]  > [Playback on TV]Wi-Fi 
						

							273
10. Using the Wi-Fi/NFC Function
Printing Wirelessly
∫Methods for sending and images that can be sent
•
Some images may not be sent depending on the device.•For details on how to send images, refer to  P299.
1Select the menu.
2Select [Via Network] or [Direct], and connect. (P292)3Select a printer you want to connect.
4Select pictures, and then print.
•The procedure for selecting pictures is the same as the one for when the USB connection 
cable is connected.
For details, refer to  P339.
•To change the setting or disconnect, press [Wi-Fi].  (P256)
Not available in these cases:
•Motion pictures cannot be printed out.
You can send images to a compatible printer, and print 
them wirelessly.
JPEGRAWMP4AVCHDMP4 
(LPCM)MOV3D
Select and send the images
( [Send Images Stored in the Camera] ) ±
—— — — ——
Preparations:
•
You can print out recorded pictures wirelessly from a PictBridge (wireless LAN-compatible)¢ 
printer.
¢ Compliant with the DPS over IP standards.
For details on the PictBridge (wireless LAN-compatible) printer, contact the respective 
company.
> [New Connection]  > [Send Images Stored in the Camera]  > [Printer]Wi-Fi 
						

							10. Using the Wi-Fi/NFC Function
274
When sending images to AV device
You can send pictures and motion pictures  to AV devices in your house (home AV 
devices). You can also send them to the devices  (external AV devices) of your family or 
friends living away from you via “LUMIX CLUB”.
∫ Methods for sending and images that can be sent
•
Some images may not be played back or sent depending on the device.
•For information on the playback of images, check the operating instructions of the destination 
device.
•For details on how to send images, refer to  P299.
A
Wireless access point BHome AV device CExternal AV device
JPEGRAWMP4AVCHDMP4 
(LPCM)MOV3D
Sending an image each time a 
recording is made
([Send Images While Recording]) ±
—— — — — ±
Select and send the images
( [Send Images Stored in the Camera] ) ±
—— — — — ±
Preparations:
When sending a picture to [Home], set your device to DLNA waiting mode.
•
Read the operating instructions of your device for details.
When sending images to [External], the following are required:
•Registration to “LUMIX CLUB” (P286)
•Address number and access number acquired by the destination External AV device.  (P291)
Sending an image each time a recording is made ([Send Images 
While Recording] )≠
P275
Select and send the images ([Send Images Stored in the Camera]) ≠
P275
.7/+:%.7$ 
						

							275
10. Using the Wi-Fi/NFC Function
1Select the menu.
2Select [Home] or [External].3Select [Via Network] or [Direct], and connect. (P292)
•When [External] is selected, [Direct] cannot be selected.
4Select a device you want to connect.
•When the connection is complete, the screen is displayed. To change the send setting, 
press [DISP.].  (P301)
5Take pictures.
•To change the setting or disconnect, press [Wi-Fi].  (P256)
You cannot change the settings while sending pictures. Wait until sending is complete.
1Select the menu.
2Select [Home] or [External].3Select [Via Network] or [Direct], and connect. (P292)
•When [External] is selected, [Direct] cannot be selected.
4Select a device you want to connect.
•When the connection is complete, the screen is displayed. To change the send setting, 
press [DISP.].  (P301)
5Select [Single Select] or [Multi Select].
•To change the setting or disconnect, press [Wi-Fi].  (P256)
Sending an image each time a recording is made ([Send Images While 
Recording] )
> [New Connection]  > [Send Images While Recording]  > [AV device]
Select and send the images ([Send Images Stored in the Camera])
> [New Connection]  > [Send Images Stored in the Camera]  > [AV 
device]
[Single Select] setting
1 Select the picture.
2 Select [Set].
[Multi Select] setting
1 Select the picture. (repeat)
•
The setting is canceled when the picture is selected 
again.
2Select [OK].
•The number of pictures that can be sent by [Multi 
Select] is limited.
•Confirmation screen is displayed. It is executed when [Yes] is selected.
Wi-Fi
Wi-Fi
6HW
2. 
						

							10. Using the Wi-Fi/NFC Function
276
When sending images to PC
∫Methods for sending and images that can be sent
¢ A motion picture recorded in [AVCHD] can be sent to [PC] if the file size is 4 GB or smaller. It 
cannot be sent if the size is greater than 4 GB.
•Some images may not be played back or sent depending on the device.•For information on the playback of images, check the operating instructions of the destination 
device.
•For details on how to send images, refer to  P299.
You can send pictures and motion pictures recorded 
with this unit to a PC.
JPEGRAWMP4AVCHD¢MP4 
(LPCM)MOV3D
Sending an image each time a 
recording is made
([Send Images While Recording]) ±±
—— —— ±
Select and send the images
( [Send Images Stored in the Camera] ) ±±± ± ± ±±
Preparations:
(On the camera)
•
If the workgroup of the destination PC has 
been changed from the standard setting, you 
also need to change the setting of this unit in 
[PC Connection]. 
(P302)(On your PC)
•Turn the computer on.•Prepare folders for receiving images on the 
PC before sending a picture to the PC. 
(P277)
Sending an image each time a recording is made ([Send Images 
While Recording] ) ≠
P278
Select and send the images ([Send Images Stored in the Camera]) ≠P279 
						

							277
10. Using the Wi-Fi/NFC Function
•Create a PC user account [account name (up to 254 characters) and password (up to 32 
characters)] consisting of alphanumeric characters. An attempt to create a receive folder may 
fail if the account includes non-alphanumeric characters.
∫When using “ PHOTOfunSTUDIO ”1Install “ PHOTOfunSTUDIO ” to the PC.
•For details on hardware requirements and installation, read “About the supplied software” 
(P330) .
2Create a folder that receives images with “ PHOTOfunSTUDIO ”.
•To create the folder automatically, select [Auto-create]. To specify a folder, create a new 
folder, or set a password to the folder, select [Create manually].
•For details, refer to the operating instructions of “ PHOTOfunSTUDIO ” (PDF).
∫When not using “ PHOTOfunSTUDIO ”
(For Windows)
Supported OS: Windows XP/Windows Vista/Windows 7/Windows 8/Windows 8.1
Example: Windows 7
1Select a folder you intend to use for receiving, then right-click.
2Select [Properties], then enable sharing of the folder.
•For details, refer to the operating instructions of your PC or Help on the OS.
(For Mac)
Supported OS: OS X v10.5 to v10.9
Example: OS X v10.8
1Select a folder you intend to use for receiving, then click on the items in the 
following order.
[File]   [Get Info]
2Enable sharing of the folder.
•For details, refer to the operating instructions of your PC or Help on the OS.
To create a folder that receives images 
						

							10. Using the Wi-Fi/NFC Function
278
1Select the menu.
2Select [Via Network] or [Direct], and connect. (P292)3Select the PC you want to connect to.
•When the PC you want to connect to is not displayed, select [Manual Input], and enter the 
computer name of the PC (NetBIOS name for Apple Mac computers).
4Select the folder you want to send.
•When the connection is complete, the screen is displayed. To change the send setting, 
press [DISP.].  (P301)
5Take pictures.
•To change the setting or disconnect, press [Wi-Fi].  (P256)
You cannot change the settings while sending pictures. Wait until sending is complete.
Sending an image each time a recording is made ([Send Images While 
Recording] )
>[New Connection]  > [Send Images While Recording]  > [PC]
Wi-Fi 
						

							279
10. Using the Wi-Fi/NFC Function
1Select the menu.
2Select [Via Network] or [Direct], and connect. (P292)3Select the PC you want to connect to.
•When the PC you want to connect to is not displayed, select [Manual Input], and enter the 
computer name of the PC (NetBIOS name for Apple Mac computers).
4Select the folder you want to send.
•When the connection is complete, the screen is displayed. To change the send setting, 
press [DISP.].  (P301)
5Select [Single Select] or [Multi Select].
•To change the setting or disconnect, press [Wi-Fi].  (P256)
•Folders sorted by the sent date are created in the specified folder, and pictures are saved in 
those folders.
•If the screen for a user account and password entry appears, enter the one you set on your PC.•When the computer name (NetBIOS name for Appl e Mac computers) contains a space (blank 
character), etc., it may not be recognized correctly.
If a connection attempt fails, we recommend that you change the computer name (or NetBIOS 
name) to the one consisting of only alphanumeric characters, with a maximum of 
15 characters.
Select and send the images ([Send Images Stored in the Camera])
>[New Connection]  > [Send Images Stored in the Camera]  > [PC]
[Single Select] setting
1 Select the picture.
2 Select [Set].
[Multi Select] setting
1 Select the picture. (repeat)
•
The setting is canceled when the picture is selected 
again.
2Select [OK].
•The number of pictures that can be sent by [Multi 
Select] is limited.
•Confirmation screen is displayed. It is executed when [Yes] is selected.
Wi-Fi
6HW
2. 
						

							10. Using the Wi-Fi/NFC Function
280
Using Web services
You can send pictures and motion pictures to an SNS, etc. via “LUMIX CLUB”.
By setting up automatic transfers of pictures and motion pictures to the Cloud Sync. 
Service, you can receive the transferred pi ctures or motion pictures on a PC or 
smartphone.
A Wireless access point BWeb service CCloud Sync. Service
Preparations:
To send images to a web service or a cloud folder, you need to register to “LUMIX 
CLUB”  (P286).
To send images to a web service, you need to register the web service.  (P282)
When sending images to web service≠
P281
When sending images to Cloud Sync. Service ≠
P284
.7/+:%.7$