Panasonic Digital Business System Section 300 Installation Guide

Section 400 FFl 
Issue 2 July 1993 DBS Programming Instructions 
CPC-A / 3.0. CPC-B / 2.0 / 3.0 / 4.0 
f 
Determines whether Tl channels are used 
The robbed bit setting determines lfAJ3CD 
as outgoing only, or bothway. 
signaling is used. ABCD signaling robs bits 
~ from the Tl channels and uses those bits to 
..:“.$;, 
transmit signaling information. 
O=Bothwav 
l=Outgoing only 
cw3 
--::~~ 
O=Off (ABCD signaling is not used.) 
~~~ 
l=On @BCD signaling is used.) 
.:‘i~~~~~~ 
#@ggy$:: 
For changes to...

DBS Programming Instn~ctions 
Section 400 FFl 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
Issue 3 July 1993 
Determines whether the system expects DP ‘hnsmits dial tone hm the Tl channel to 
or DTMF digits for incoming DID or DNIS another DBS within a private network. 
calls. 
If YXIVIF” is selected, the DBS must be 
c- ) equipped with an MFR card. 
81  

Section 400 FFl 
Issue 2 July 1993 DBS Programming Instructions 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
lbrmn.its busy tone from theT1 channel to lhnsmits dial tone from the Tl channel to 
another DBS within a private network. DBS stations. 
o=off 
l=On o=m 
l=On 
c 
82  

DBS Programming Instructiona 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
Transmits ringback tone f?om theT1 chan- 
nel to the central office 
within a private network. or another DBS 
o=off 
l=On 
section 400 FFl 
Issut% 3 July 1993 
Associates a dialed number with a station. 
Associatesafour-digitdialednumberwitha 
station number. DNIS is available onlywith 
theT1 Interface. 
Stations are numbered using one of two 
patterns: 10-69 or 100-699. 
83  

Section 400 
FF2 
DBS 
Issue 3 July 
1993 Programming Instructions 
WC-A / 3.0. CPC-B / 2.0 
/ 3.0 / 4.0 
To set a central o&e line in service, or to 
remove it from service, this option must be 
used. To set a central office line for touch-tone or 
pulse dialing. (10 pulses per second), this 
option must be used. 
To set any central office line in service. 
enter: To set any central office line for touch tone 
dialing, enter: 
,lDBSl.ine~ort numbed#.l#.OW 1. rDBs Iine Dolt mmbex~#. 2#. on 
To remove any...

DBS Programming Instructions 
CPC-A / 3.0 WC-B / 2.0 / 3.0 / 4.0 
I 
/ 
 
 
Section 400 FF2 
Issue 3 July 1993 
To place a central office line in a group so 
that it can be one of many that can be 
automatically chosen for outbound 
dialing, this option must be used. 
When dialing a “9” from an SLT or 
digital extension, or pressing an FF 
key that is set as a pooled trunk key, 
any available line in the group will be 
accessed. 
To not include a central office line to be a 
member of the “9” access...

Section 400 FF2 
Issue 3 July 1993 
To set any central office line to be a 
member of the “86” access group, enter: 
[eez], (DBS line port number)#, 9#, l# 
To remove any central office line &om any 
access group (81 through 86), enter: 
1. (DBS line Mlrt numberld. (49lW, 
06 
The same trunks may appear in more 
than one line access group and include 
access group 9. 
The line selection in a particular group is 
madef+omthehighestavailablelinenumber 
to the lowest available line number. 
DBS Programxdq...

DBS Programming Inst.ructions 
WC-A / 3.0 CPC-B / 2.0 / 3.0 / 4.0 
i Section 400 FF2 
Issue 3 July 1993 
To set acentral office Iine(s) to automaticaRy 
provide DiSAtone upon connection with an 
inbound cakr. this option must be set 
To set any central office line to provide a 
DISA tone when connected to a new 
inbound caller, enter: 
~],@BSlinep0rtnumher)#, ll#, l# 
To ‘set any central of& I&e so that it does 
not provide a DISA tone when connected 
to a new inbound caller, enter:...

Section 400 FF2 
Issue 3 July 1993 DBS Programming Instructions 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
To set an automatic pause during dialing 
on a central of&e line defined as PBX this 
option must be used. 
To set the automatic pause on line 15 for 
example, (once line 15 is defined as a 
PBX). enter: 
pm. SW. 13w. 19 
To disable the automatic pause on line 12 
for example. (once line 12 is defI.txd as a 
PBX), enter: 
pF2], 128, 136, ow 
See [FFl], 3.# 12# program option, for the 
timer used for this...

DBS Programming Instructions 
WC-A 
/ 3.0 WC-B / 2.0 / 3.0 / 4.0 Section 400 FF2 
Issue 3 July 1993 
To allow a central ofike line(s) to be able to 
be used in an unsupervised conference 
call, this feature is used. 
To disable line 22, for (xample, so that it 
cannot be used in aline to line conference, 
enter: 
JFKBl. 22#. 16W. OW 
To set line 22 to be able to be used as one 
of the lines in a line to he conference. 
enter:. 
c ‘> m], 22W. 16#, l# 
See [FF3], 13# program address to start a 
conference...