Panasonic Digital Business System Section 300 Installation Guide

Section 400 FFl 
Issue 2 July 1993 DBS Programming Instructions 
WC-A / 3.0, WC-B / 2.0 / 3.0 / 4.0 
The ring pattern to a device that is 
connected to a Panasonic ringer box, and 
receives an inbound DISA call can be set 
to mering patterns. The pattern can be 
set to a one second on, three second off 
ring burst, or it can follow any of the 
patterns found in the normal Central 
Oi&etransferringpattemsfoundin[FF1]. 
2#, l#, 22#. 
TosettheSLTDiSAringpattemto l.Osec, 
on / 3.0 set off, enter: 
Jmll. 2R....

DBS Programming Instructions 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 section 400 FFl 
Issue 3 July 1993 
If the parity check has been set, this 
option determines whether the check is 
based on an even count or an odd count. 
To set the parity check for an odd value, 
enter: The data transmission speeds between 
the DBS SMDR port and peripheral 
equipment can be set in arange from 300 
bits per second to 9600 bits per second. 
To set the data transmission speed to 300 
bps, enter: 
pm]* 2#,2#, 2#,OW...

Section 400 FFl DBS Programming Instructiona 
Issue 2 July 1993 WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
f 
‘This option sets the length of the stop-bit 
for transmitted data. 
To set the length of the stop bit data to 
1 
bit. enter: 
~ll.2#,2#.4#. l# 
To set the length of the stop bit data to 1.5 
bits, enter: Sets the length of *he transmitted data 
string at 5 to 8 bits. 
To set the length of the data string at 5 
bits, enter: 
CFFl], 2w, 2w. w, 1w 
To set the length of the data string at 6 
bits, enter:...

DBS Programming Instructions 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 Section 400 FFl 
Issue 3 July 1993 
The SMDR printer can record data for 
outgoing calls only or both outbound 
and inbound calls. 
To set the SMDR. to record only 
outbound call information, enter: 
EFl], 2#, 2#, 6#, OW 
To set the SMDR to record inbound and 
outbound call information, enter: 
FFll. 2#. 21. 6#. l# 
The system must be in the SMDR mode 
so that the printer can provide usable 
SMDR data. This is done by performing 
the...

Section 400 FFl 
Issue 2 July 1993 DBS Programming h~~tn~ction~~ 
WC-A / 3.0, CPCB / 2.0 / 3.0 / 4.0 
f 
Titles such as Time, Duration and CO# 
are printed every 60 lines if this feature 
is enabled. 
To disable the printing of a title line on 
every 60th line of the SMDR report, 
enter: 
JFFll. 2#.2#. 8#. 0# 
To set the printing of a title line on every 
60th line of the SMDR report, enter: The X-On/X-Off feature of the DBS is a 
k&ware switch” to temporarily stop the 
DBS fkom sending data out the SMDR...

DBS Programming Inst~ctions 
WC-A / 3.0, 
CPC-B / 2.0 / 3.0 / 4.0 
Section 400 FFl 
Issue.3 July 1993 
The baud rate that is used for remote 
programming capability can be set to 300 
or 1200 baud. 
To set the baud rate for remote 
progmmmingcapabilityto 3OObaud. enter: 
fH@Fl],2#,2#, lO#,O# 
To set the baud rate for remote 
programming capability to 1200 baud, 
enter: 
jmll. 2#.2#. low. 1n 
When a remote administration “B” card is 
used, either baud rate setting can be 
utilized. However when a remote...

Section 400 FFl DBS Programming Instructions 
Issue 2 July 1993 CPC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
To automatically insert a pause in the 
PBX access code dialing (and SSD. PSD 
codes), after the output of the first and/or 
second, and/or third code number, use 
this option. The purpose for the use of this 
pause is that it may take several seconds 
to connect with a central office telephone 
line. 
To set a pause after automatic outpuke of 
the first dialed digit, (which is assumed to 
be L( 1” in...

DBS Programming In8t~~ction.s 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 section 400 FFl 
Issue 3 July 1993 
The ring pattern for the universal night 
answer (UNA) relay-terminals can be set 
foracontinuousorintermittent ringburst. 
To set the ring pattern for a 1 second on/ 
3 second off pattern, enter: 
JFFll. 2#.4#. l#.OW 
To set the ring pattern for a continuous 
ring burst, enter: 
pFl],2#,4#, lW, 1w 
c j n 
g@yJg$& 
.::.. .:.. ::.: I.::: 
When using a non central office sound. 
source for the buzzer,...

section 400 FFl 
DBS [email protected]~ hstnrctions 
Issue 2 July 1993 CPC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
The 20 allowable features that can be 
classified into any class of service 
grouping are: 
Fa8tum 
Dial Tone On/Off 1#50) 
2 Head/Handset Exchange (#51) - 
3 BGM On/Off (#53) 
/ 4 (Absence Message Set/Reset (71) 
5 
Call Forward Set/Reset (72) 
6 
Do Not Disturb (73) 
7 
Station Lockout (74) 
8 Park Access (75) 
9 
Park Pick Up (76) 
10 
Meet Me Answer (771 
1 11 IUNA Pickuo (78) 
12 IDirect pick Up (79)...

DBS Programming Instructions 
Section 400 FFl 
CPC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
Issue 3 July 1993 
Verified forced account codes can have a 
toll restriction class of service assigned to 
them. A caller that uses a particular 
account code with atoll restriction class of 
service assigned to it would then be 
allowed to dial any telephone number 
allowed under the toll restriction class of 
service for the verified forced account 
code.Theextensiontollrestrictionclassof 
service in this case would...