Panasonic Digital Business System Section 300 Installation Guide

zce_-_r 
Digital Business System 
Section 400 
Panasonic  

DBS Programming Instructions 
WC-A / 3.0. CPC-B / 2.0 / 3.0 / 4.0 
Chapter 1 
General Program Outline 
Prior to programming the system make 
certain you have completed the following 
steps. 
Step 1: 
Corr6rn-r the DBS system feature operations 
meet the end userrequirements as outlined 
in Section 700. 
Step 2: ‘-“. ~ ,.,-’ : 
Prepare section 450 with the end users 
requirements. 
Step 3: 
Confirm the hardware required for the 
end user. 
_I._ 
‘ :. ., 
Step 4: 
Initialize the system to the default...

Section 400 FFl 
issue 2 July 1993 
Before beginning to program a newly 
installed DHS for the first lime, set the 
system programs to the default values by 
following steps 
1 through 5 below: 
1.TurnoffthepowerfortheMainCabinet. 
(Both cabinets if a dual cabinet 
configuration is being used.) 
2. Slide the CPC RAM switch to the 
CLEAR position. 
3. Turn on the power for the Main 
Cabinet(s), then 
wait until the bottom 
LED on the CPC card 
stops flashhg. 
Note: The CPC-B card will take about 
twice as...

DBS Programming Instructions 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
Chapter 2 
Requirements for p~gramming 
Section 400 FFl 
Issue 3 July 1993 
I 
2-l PREPARING PROGRAMMING 
DATA TABLE 
I 2-2 HOW TOACCESS 
RR-G MODE 
Prior to programming the DBS, complete 
Section 450 (Programming Tables). 
Review the desired functionality 
with the 
end user, making any additional changes 
as required. Ifthe end user has requested 
specific functionality you are unfaxmliar 
with, refer to Section 700 to confum the 
. DBS...

Section 400 FFl 
Issue 2 July 1993 DBS Ro@amming instructions 
CPC-A / 3.0. CPC-B / 2.0 / 3.0 / 4.0 
When programming from a telephone 
connected to the test terminal (CN3) of 
the main DBS cabinet, slide the switch on 
the cabinet to the test mode. This switch 
provides a direct connection to ports 7 
and 8. 
To enter the programming mode from the 
test terminal port, perform the following 
steps: 
[ON/OFF], #98,9999 (or presently used 
Authorization code), [PROG]. ##, then 
proceed with the FF key...

DBS Programming Instructions 
CPC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 Section 400 FFl 
Issue 3 JuIy 1993 
When programming from a terminal 
connected to the RS232C (SMDR) port, 
perform the .following steps: 
1. Make certain the cables are 
configured and connected as outlined 
in Section 300. 
2. Make certain the DBS is in the SMDR 
mode by performing the following steps 
i?om the attendant port: 
!’ [ON/OFF], #93 ! 
3. Perform the following steps from the 
terminal:.. 
. . 
#99, 9999 
4. After the DBS...

Section 400 FFl 
DBS Programming Instructions 
Issue 2 JuIy 1993 
WC-A / 3.0. CPC-B / 2.0 / 3.0 / 4.0 
2-3 PROG- G METHOD 
Example of date/time program 
entries: 
To set the date from extension port 
number 1: 
Press [ON/OFF], [PROG] (“F* is 
displayed), # (“F#” is displayed), # 
(“Program Mode” is displayed on line 1, 
“MAIN MODE” is displayed on line 2). 
Ffress [FFl]. (“System Program” is 
displayed on line 1, ‘SELECT 
SUB-MODE” is displayed on line 2). 
Press 1, #, (“Select Time Mode” is 
displayed...

DBS Programming Instructions Section 400 FFl 
CPC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 Issue 3 July 1993 
Page Default Value 
(FFI 
[FFI 
[FFI 
[FFI 
[FF 1 
(FF 1 
(FFI 
[FFI 
[FFI 
[FFI 
[FFI 
[FFl 
[FFl 
[FFI 
(FFI 
[FFI 
i::; 
[FFI 
[FFI 
[FFl 
i [FFI 
[FFl 
[FFI 
[FFl 
IFFI -1-1 ............................ 
DAY/DATE ....................................................................... 
-1-2 ............................ 
TIME...

Section 400 FFl 
DBS Pqpmming Insimction~ Issue 2 July 1993 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
[FFl]-2-4-1 ........................ 
RING PATIFRNS FOR UNA TERMINALS (M.C & Bl 
........... 1 set on 3 set OR ...... 37 
[FFl]-2-4-(2-g) ................... 
EXTERNAL PAGE CONTROL FOR PAGING CROUPS .......... No settings ............... 37 
ml]-2-5-(l-8)-( l-20) ............ 
EXIENSION CIASS OF SERVICE (CPC-B 3.0) 
........................ Class 0 
...................... 
37 
l~11-2~~1-100)-@001-~l.. .......

DBS Programming Instructions Section 40OFFi 
CPC-A/ 3.0, CPC-B / 2.0 / 3.0 /4.0 
Issue 3 July 1993 
[FFl]-8-4-2-8 . . . . . . . . . . . . . . . . .._. . . ANSWER SUPERV 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._........... 
600 ms 
[FFlj-8-4-2-9 . . . . ..I............... IMM-GLARE -lIMER . ..-..........._..... 
61 
[FFlj-8-4-2- 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
60...