Panasonic Digital Business System Section 300 Installation Guide

Section 400 FF2 
Issue 3 July 1993 DBS Programming Instructions 
CPC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
WhenaazntmIoi3keIinecaIIisdisconnected, 
theaxdralofficeSendSadiScoMectSignal. 
TheDESneedstoint.erpretaIIvaIidsi@aIs, 
so that the central office line can be 
disco~ected fbm it This feature provides 
this function. 
I 
. -Ins I 
I l# I >5OIllS 14 zQ5oms. I 
I 2# I >loOlllS 
I 1o# I >5OORlS 
I 
I 3ff I >15oms 1 11% I 9350 ms 
I 
I7# 1 235oms I15# 1 >75oms / 
Any centraI of&e Iine that is set as a DISA...

DBS Programming Inst~ctione Section4OOFF2 
WC-A / 3.0 WC-B / 2.0 / 3.0 / 4.0 
hue 3JulJr 1993 
AI-IY central oflke line that is set as a DISA 
line. can be set to stop DISA operation at 
a speclfied time. 
To set a central oflEe Iine that has DISA 
capability to stop DISA operation at a 
certain time, enter: 
fFF2], (DBS line port number)#, 20#, 
HH.MM#. 
,f “ 
 To reset DISA ston time canabiI.itv to the 
default i.nitializedvaIue. Dress IFF21. (DF3S 
rmrt numberlt 20##. lCONFl. iON/ 
%I. Determines...

Section 400 FF2 
Issue 3 July 1993 
Any central office line position in the DBS 
can be set as either a loop-start or 
ground-start circuit. 
To set central office line position 3, for 
example, as a loop start line, enter: 
ml. 3#.21#.0# 
To set central o&e line position 7. for 
example, as a ground start line, enter: 
pF2],7#,21#, l# 
Ground. start line capability is available 
only with CFC-B configurations. 
lfaground-starttrunk is enabled, FFl], 
3#. %I## and 21# progmm addresses must 
beset 
Trunk...

DBS Programming Instructions 
CPC-A / 3.0 WC-B / 2.0 / 3.0 / 4.0 Section 400 FF2 
Issue 3 July 1993 
AnycentmlofficelinepositionintheDBScan 
be set as either aloop-start, ground-start or 
DIDcimuit..Loopstartlinesarethemost 
common @pe of centml office line. Ground 
start lines pi&on-n similaj, except they 
provide the” most reliable connection 
between the Central office and DBS, in 
terms of positive disconnect signals and 
no possibility of line crashes or ‘glare”....

Section 400 FF2 
Issue 3 July 1993 DBS Ro@ammin~ Ins~ctions 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
After connecting with a Central office, 
the DBS will wait 65 milliseconds 
before accepting the digits of a dialed 
number, or can be set to wait for a 
“wink” signal from a central office 
before accepting the digits of a dialed 
number. 
To set the DID line to immediately accept 
the dialed number Tom the central oflice. 
enter: 
. CDBS DID line sort numbed%, 
22w. on 
To set the DID line to wait for the...

DBS Programming Instructions Section400 FF2 
CPC-A / 3.0 WC-B / 2.0 / 3.0 / 4.0 
Issue 3July1993 
Once the central office starts to send the 
dialed digits to the DBS over a DID line, it 
is necessary to be able to disconnect the 
line in the case of a transmission 
disruption.-The maximum amount of 
time that is allowed for the transmission 
of the digits is set with this feature. 
Tinle Time 
o# 
No Time Out 8# 22Second.5 
I I  l# 15 seconds 
I I  w 23Second.s 
I 
2# 16Seconds 
lo# 24 Seconds 
3#...

Section 400 FF2 
Issue 3 July 1993 DBS Programming Instructions 
WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
Assigns a port class to each trunk port 
that will access the Tl. Port classes are 
used to assign pad levels to connections 
made via the Tl. (Pad levels control 
volume.) 
Figure 1 shows circuit-typenumbers. Cir- 
cuit Apes 4-6 are used to assign port 
classes to tlunks. 
Figure 1. Circuit-type Numbers 
circuit Types No. 
K-TEL 1 
SLT 
2 
DATA# 3 
Analog CO Trk 4 
Tl Master 
5 
Tl Slave 6 
OPTION l* 7...

i ,’ 
DBS Romanming Instructions 
WC-A / 3.0 CPC-B / 2.0 / 3.0 / 4.0 Section 400 FF3 
Issue 3 July 1993 
3-3 EXTENSION PROGRAM 
SETTINGS 
The choice of 2-digit or 3-digit extension 
numbers are assigned in this feature. 
To set extension port 3 to extension 
number 333, for example, enter: 
pF3], 3#, I#, 333w 
To set extension port 4 to extension 
number 222, for example, enter: 
FF31,4#, I#, 222% 
To clear a DBS extension nor-t number, 
press lFF31. (DBS extension nort 
number)#, l#. lCONF1. 
Cl>...

Section4OOFF3 
DBS Rogramming lnstn~ctions 
Issue 3July1993 
CPGA/ 3.0, WC-B /;r.O / 3.0 /4.0 
Some DBS extension ports are 
automatically configured as to the type of 
equipment, when the hardware is 
physically installed on the port. Terminal 
type designations are assigned to 
extension hardware as follows: 
l#: Single-line telephone devices will 
automaticallyconfiguretheextensionport 
28: 16 key telephone devices will 
automatically configure the extension port 
3#: 22 key telephone devices will...

DBS Programming I.nstructionf~ 
Section4OOFF3 
CPGA/ 3.0 CPGB / 2.0 / 3.0 / 4.0 
Issue 3July1993 
Some DBS extension ports are 
automatically configured as to the type of 
equipment, when the hardware is 
physically installed on the port. Terminal 
type designations are assigned to 
extension hardware as follows: 
OW: No assignment 
l#: Single-line telephone devices will 
automaticallyconfiguretheextensionport 
2#: 16 key telephone devices will 
automaticallyconfrgurethe extensionport 
3#: 22 key...