Panasonic Central Processing Unit Wj Mpu955a Operating Instructions

31
Setup Encoder Itself 
In order to communicate with the CPU, the encoder device must also be configured. You can access the encoder device
through its Web interface using Microsoft Internet Explorer. Following is an example of the system layout and information to be
filled into the table.
Encoder #
1
2
3
4Operation Mode
Main CPU mode
Main CPU mode
Main CPU mode
Main CPU modeIP Address
192.168.1.10
192.168.1.11
192.168.2.10
192.168.2.11Subnet Mask
255.255.255.0
255.255.255.0
255.255.255.0...

32
Decoder #
Digital Video Decoder Devices
Digital video decoder devices refer to MPEG2 video decoder devices (WJ-GXD900). They connect to the CPU through an
Ethernet switching hub in an IP based network. Refer to the Operating Instructions of MPEG2 encoder/MPEG2 decoder.
Connect with CPU
The video decoders connect with the CPU through its Ethernet port and one or more switching hub units. The system can sup-
port up to 64 video decoder devices.
Setup from Admin Console 
In order to be added to the...

33
Admin Console
Admin Console is a system database management software. The software operates in the Microsoft®Windows®environment.
Refer to the Admin Console Users Guide for details.
To connect a personal computer (PC) with the CPU, perform the following. (Refer to the Admin Console Users Guide for
details.)
1. Install the admin console on a PC. (Refer to the Admin Console Users Guide for details.)
2. Enter the CPU IP address in the tool’s CPU screen. (The CPU screen appears when you launch the tool...

34
Digital Disk Recorders
Digital Disk Recorder is the combination of hard disk recorder (a recording device using a hard disk drive to record camera
pictures) and video multiplexer. Refer to the Operating Instructions of digital disk recorder for details.
Connect with CPU
The digital disk recorders connect with the CPU through its Ethernet port and one or more switching hub units. The system can
support up to 64 video decoder devices. (NTSC model only)
Setup from Admin Console 
In order to add a...

35
CONNECTION OF WJ-SX650 512 x 64
FULL MATRIX SYSTEM 

36
Connection with System Devices
System Controllers
Regarding system controllers, the connection and setup are same as the GX system. (Refer to p. 28.)
Matrix Switcher WJ-SX650 Series
Network Board Installation
The back panel (OUT X-1) of Video Output Board 1 should be replaced by Network Board WJ-PB65E01.
Connect with CPU
The matrix switchers connect with the CPU through its Ethernet port and one or more switching hub units. This system can
support up to six WJ-SX650 SubNodes. The CPU assigns the...

Vertical Interval Synchronization
Connect the coaxial cables as shown below.
Set DIP SW4005 Bit4 to ON for each Video Output Board 1.
37
ID
1
2
3
4
5
6I/F
0
0
0
0
0
0IPA
192.168.200.1
192.168.200.2
192.168.200.3
192.168.200.4
192.168.200.5
192.168.200.6BRIDGE
–
–
1-32
–
–
33-64CONTROL
1-256
257-512
–
–
–
–OSD
–
–
1-32
–
–
33-64SWITCH
1-256, 1-32
257-512, 1-32
–
1-256, 33-64
257-512, 33-64
–ALARM
–
–
–
–
–
–Address
1
2
3
4
5
6
SX650 Output Board MODE Switch Settings
(Bit Order : 1-2-3-4-5-6-7-8)...

38
SubNode 5 SubNode 4 SubNode 2
38
Connect with Each SX650 SubNode via Coaxial Cables
*1-1 Video Connection between SubNode 1 and SubNode 3 (Bridge)
SubNode 1 SubNode 3
Monitor Output Connectors 1 (Output Board (1)) Camera Input Connecters 1 (Input Board (1))
::
Monitor Output Connectors 16 (Output Board (1)) Camera Input Connecters 16 (Input Board (1))
Monitor Output Connectors 1 (Output Board (2)) Camera Input Connecters 17 (Input Board (1))
::
Monitor Output Connectors 16 (Output Board (2)) Camera...

3939
*2-1 Loop-thru Connection between SubNode 1 and SubNode 4
SubNode 1 SubNode 4
VIDEO OUT 1 (Input Board (1)) Camera Input Connecters 1 to 8 (Input Board (1))
VIDEO OUT 2 (Input Board (1)) Camera Input Connecters 9 to 16 (Input Board (1))
VIDEO OUT 3 (Input Board (1)) Camera Input Connecters 17 to 24 (Input Board (1))
VIDEO OUT 4 (Input Board (1)) Camera Input Connecters 25 to 32 (Input Board (1))
VIDEO OUT 1 (Input Board (2)) Camera Input Connecters 1 to 8 (Input Board (2))
VIDEO OUT 2 (Input Board...

40
*2-2 Loop-thru Connection between SubNode 2 and SubNode 5
SubNode 2 SubNode 5
VIDEO OUT 1 (Input Board (1)) Camera Input Connecters 1 to 8 (Input Board (1))
VIDEO OUT 2 (Input Board (1)) Camera Input Connecters 9 to 16 (Input Board (1))
VIDEO OUT 3 (Input Board (1)) Camera Input Connecters 17 to 24 (Input Board (1))
VIDEO OUT 4 (Input Board (1)) Camera Input Connecters 25 to 32 (Input Board (1))
VIDEO OUT 1 (Input Board (2)) Camera Input Connecters 1 to 8 (Input Board (2))
VIDEO OUT 2 (Input Board...