Panasonic AY-RP500 Installation Manual

49
(d) If the following message appears during uninstall,
click .
( e ) Check disk scheduling
Enter chkdsk /f c: on the command prompt panel.
After that, You will be asked Check disk
scheduling (Y/N)?
So enter y on the command prompt panel. 
This executes the check-disk in restarting. 
( f ) Restart. (The check-disk automatically runs at
restart.)
Select Shutdown from Start.
Add a check mark to Restart Computer and click
.
(g ) Directory delete
If c:¥TARGA2KDV and subsequent directories remain
in...

50
( d ) Click  in Display Type. 
( e ) Click  in Display Modification.
( f ) The directory of the display driver is to be opened,
so enter
C:¥TARGA2KDV¥WINNT¥Display and click  .
( g ) Confirm that Truevision DVR Display is displayed
on the screen and click  .
( h ) The message The drivers were successfully
installed appears.  Click  .
( i ) Click  in Display Types
( j ) Click  in Screen Properties
( k ) The message You must restart your computer
888
appears.  Click  .
( l ) Windows NT starts up.  When...

51
Tool Box
OPERATING PROCEDURES
Refer to the reference manual for details on how to store and edit video and audio material.
nStarting the System
1. Turn on the power switches on the peripheral equipment, any hard disk units, and the computer, in that order.
2. Start up Windows NT.  Double click DVEdit Shortcut.
3. After the application starts up, the initial screen (Tool Box, BIN Manager, and BIN Window) is displayed on the per-
sonal computers monitor.
Computer Display is shown below.
BIN Manager
BIN...

523.3. SCSI Device Setup Check
Press [Ctrl]+[A] on the BIOS screen to show the SCSI
Utility screen and check the following.
( a ) Are all the maximum sync transfer rate settings 40.0
MB?  (Check both channels A and B.)
(b) Are all the connected disks Verify once on the SCSI
Utility?  (Check both channels A and B.)
3.4. Setup Check with Administrator
Start the administrator panel by taking the steps in the
order of Start 
pProgram pManagement Tools
(Common) 
pDisk Administrator, and check the
following.
(...

53 3.6. Others
( a ) Do the jumper settings (IRQ, I/O address) on the JOG
board agree with the DVEdit software settings?
(b) Is the Targa driver installed?
( c ) Is the SCSI driver installed?
(d) Is the display driver changed for Targa?
( e ) Is DVEdit installed?
( f ) Is the font installed in Windows?
(g) Is the font additionally registered in DVEdit? (Register
it with Font Setup on the Special panel.)
(h) Has the device been set up? (Set up Reference,
VTR Type, Input/Output Type, etc. with Device
Setup...

54
1. Check with Device Setup on the Special panel
that the device settings agree with the connections.
2. Clips can be created using the manual digitizer.
(About 5 each of Ado, Vdo, A/V) 
Check that an NTSC image is shown in the lower
right part of the VGA monitor.
3.Clips can be created using the batch digitizer.
(About 5 each of Ado, Vdo, A/V)
Check that an NTSC image is shown in the lower
right part of the VGA monitor.
4.Clips can be created using the title editor.
(About 5)
5.Transition settings can...

55 

56
nHow to install the board
Plug the AY-PB500 board (TARGA DV2000 board) into the PCI slot that is closest to the CPU (or the next closest slot, if
the board will not physically fit into the closest slot).  Here, firmly mount the board spacer between the guide rails on the
computer.  Screw down the cover (AY-PB500).
Then use the twist-tab wire to secure the board spacer to the guide rails inside the computer.
lFor a GATEWAY PC tower type
APPENDIX
Use the twist-tab wire to secure the board spacer to the...

57 lFor a MICRON PC tower type
Board spacer (metal type) Board spacer (plastic type)
Pass the twist-tab wire through the guide rails as shown above.
Use the twist-tab wire to secure the board spacer to the guide rails inside the computer.
Twist the twist-tab wire and secure it properly.
Check that the board spacer has been secured properly.
Connect the ground wire to the computers chassis only when the metal type of board spacer is supplied.
(Refer to page 11)
Guide rail
twist-tab wire
Guide rail...

58 lFor a MICRON PC mini tower type
Board spacer
Guide rail
twist-tab wire
Pass the twist-tab wire through a hole of the guide rails as shown above.
Use the twist-tab wire to secure the board spacer to the guide rails inside the computer.
Twist the twist-tab wire and secure it properly.
Check that the board spacer has been secured properly.
Connect the ground wire to the computers chassis only when the metal type of board spacer is supplied.
(Refer to page 11)Board spacer (metal type) Board spacer...