Panasonic AY-RP500 Installation Manual

29
23. The selected area will have the message
Unformatted.
24. In Partition on the menu bar, click Commit
Changes Now....
25.  At the message Do you want to save changes?,
click .
26. The message Disks were updated successfully.
Click .
27.  The message of the unformatted area of the disk
changes to Unknown.
28.  Click  the Unknown area of the disk to select it.
29.  In Tools on the menu bar, click Format.
30.  The format window opens.  Click    of File system,
and select NTFS.
31.  Do not set the...

30 8When four or more SCSI hard disks are for
video
Proceed with the settings following the same method
used for two video hard disks.  Assign the drive letters
alternately for channels A and B.
Example1:  Four SCSI hard disks for video 
When the 4 disks are disk 1 through disk 4 in the
Disk Administrator
Disk 1   O:Drive
Disk 2   Q:Drive
Disk 3   P:Drive
Disk 4   R:Drive
Example2:  Eight SCSI hard disks for video 
When the 4 disks are disk 1 through disk 4 in the
Disk Administrator
Disk 1   O:Drive
Disk...

31
Note:After application software is installed, the con-
tents of the video hard disks cannot be viewed
using Explorer or File Manager.  However, this is
not a malfunction.  Do not format the disks.
Note:After application software is installed, the con-
tents of the audio hard disk can be viewed
using Explorer or File Manager.  However, do
not delete the data or upload any other program
or file.  Doing so will cause the disk to stop
operating.
Note:To determine whether the hard disk is for
video or...

32
The following system connections should be made by qualified service personnel or system installers.
The system connection diagram shown below is intended as an example.  The actual connection locations may differ
depending on the model of computer used.
nKey Board, Mouse, Personal Computer Monitor and JOGPAD
lConnecting the keyboard
Connect the keyboard to the keyboard connector on the rear of the personal computer.
lConnecting the mouse
Connect the mouse to the mouse connector on the rear of the...

33 lConnecting the JOGPAD
Use the VCR/JOGPAD cable (accessory) to connect the D-sub 9-pin connector on the rear of the JOGPAD to the mini-
DIN, 8-pin JOGPAD connector on the JOG board.  Use the screws to secure the cable connector to the connector on the
rear of the JOGPAD.  Be sure to cut the power before connecting cables.
01&/

0,6/%0 4)*5
53*.

.0%&
%*7*%&

%&-&5&;
0
0
.
(050 
1
-
:
4
5
0
1
.3,

*/.3,

065

JOG board
JOGPAD JOGPADVCR/JOGPAD cable Computer (rear)
D-sub 9-pin
Mini-DIN 8-pin 

34
nConnecting the VCR
Indicates an example of system connection.
The system connection diagram shown below is intended as an example.  The actual connection locations may differ
depending on the model of computer used.
lWhen connecting a video cassette recorder designed for commercial applications
As in the figure below, [Genlock Input Control] is set to Blackburst Genlock Input if [REF IN] is input to the TARGA
board.  For details on setup, read the Special section in the software manual.
RS422...

35 lWhen connecting a video cassette recorder designed for commercial applications (2)
(When there is no sync signal generator)
Set [Genlock Input Control] to Disabled.
LTC/REF cable RS422-1 RS422-2
RS422Audio output
EE output
Commercial VCR Reference inputVideo output monitor
Video output
Speakers with built-in amplifiers Analog I/O cable
Computer (rear)
VCR/JOGPAD cableS-VIDEO OUT
R-Y/R OUT
B-Y/B OUT
Y/G OUT
R AUDIO OUT
L AUDIO OUT
R-Y/R IN
B-Y/B IN
Y/G IN
R AUDIO IN
L AUDIO IN
CV/CS OUT
LTC OUT
LTC...

36
MEMO
• Use a coaxial relay plug when connecting two coaxial cables (with BNC connectors) together.
• When not using the REF OUT signal (loop-through) on the JOG board, turn off the 75Wterminator switch on the JOG
board; and connect the termination (accessory) to the REF OUT cable.
• If a DVCPRO series VCR is used, the EE output from the VCR lags the input signal by about five frames.
Coaxial relay plug
REF OUT cable
Termination
lS-VHS VCR (No RS422 control)
Set [Genlock Input Control] to Disabled....

37
ANALOG Y/C VIDEO OUT
DIGITAL VIDEO OUT
DIGITAL AUDIO OUT
L AUDIO OUT
R AUDIO OUT
DIGITAL VIDEO IN
DIGITAL AUDIO IN
ANALOG COMPOSITE
VIDEO OUT
LTC OUT
LTC IN
REF IN
nConnecting the VCR (Serial Digital Interface : SDI)
lWhen connecting a video cassette recorder designed for commercial applications
As in the figure below, [Genlock Input Control] is set to Disable.
[TAPE/EE switch] is set to TAPE in VCR.
RS422 LTC/REF
LR
TARGA board
JOG board
LTC/REF cable RS422-1 RS422-2
Commercial VCRVideo output...

38
nTurning on the power switches
1. Turn on the power switches on the peripheral equip-
ment first.  If using an external hard disk unit, turn on
the power switch on the hard disk unit.
The power indicator of the hard disk box lights red.
2. Turn on the power switch on the computer.
Windows NT starts up.
nTurning off the power switches
Note: Before turning off the power, be certain to first
quit any application programs and Windows NT
according to the procedures described on the
following page.  If the...