Panasonic AY-RP500 Installation Manual

							Before attempting to connect or operate this product, please read these instructions completely
â
Nonlinear Editing System
Control Panel Kit
AY-RP500 
						

							Warning:
This equipment generates and uses radio frequency
energy and if not installed and used properly, i.e., in
strict accordance with the instruction manual, may
cause harmful interference to radio communications.
It has been tested and found to comply with the limits
for a Class A computing device pursuant to Subpart J
of Part 15 of FCC Rules, which are designed to pro-
vide reasonable protection against such interference
when operated in a commercial environment.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the products enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
The exclamation point within an equi-
lateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompa-
nying the appliance.The serial number of this product may be found on the
bottom of the unit.
You should note the serial number of this unit in the
space provided and retain this book as a perma-
nent record of your purchase to aid identification
in the event of theft.
Model No. AY-RP500
Serial No.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).  NO
USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SA 1965
SA 1966
For U.S.A
CONTENTS
PREFACE .......................................................................................................................................................................... 1
FEATURES ........................................................................................................................................................................ 1
PRECAUTIONS ................................................................................................................................................................. 2
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS  .......................................................................................... 3
CABLE INFORMATION  .................................................................................................................................................... 6
BOARD SETUP .................................................................................................................................................................. 9
HARD DISK SETUP ......................................................................................................................................................... 20
SYSTEM CONNECTION  ................................................................................................................................................... 32
POWERING  MAIN UNIT ON AND OFF  ........................................................................................................................... 38
OPERATING PROCEDURES  ............................................................................................................................................ 39
LOADING SOFTWARE PACKAGE  ................................................................................................................................... 40
VERSION-UP PROCEDURES FOR DVEdit  ....................................................................................................................... 44
DVEdit INSTALLATION CHECK ITEMS  ............................................................................................................................ 52
DVEdit INSPECTION DETAILS  ......................................................................................................................................... 54
APPENDIX ........................................................................................................................................................................ 56
SPECIFICATIONS ..............................................................................................................................................................60 
						

							1
The AY-RP500 Nonlinear Editing System is a combination
of powerful hardware, flexible software and a custom
human interface; developed for professional post-pro-
duction.  With the AY-RP500 Nonlinear Editing System,
nonlinear editing is a creative process that finishes your
videos to high standards while maintaining production
budgets.
PREFACE
FEATURES
• Simultaneous playback of two channels
This system can playback video on two channels,
with excellent image quality.
• DVCPRO system
The DVCPRO system is used for video compression
and decompression.
• A user interface suited for video production
Because icons are used for stills representing each
scene, editing is more intuitive and efficient in com-
parison with earlier VCR editing controllers.  The
video editing process can be conducted with even
greater efficiency by using the JOGPAD. 
• The system uses outline fonts for titles of the
highest quality The AY-AS501 application software is prerequisite.
OPERATING CONDITIONS 
						

							2
• Use the main unit or JOGPAD in an environment
where the temperature is within 32°F - 95°F (0°C - +
35°C), and the relative humidity is within 10 - 90%.
• Handle the unit with care.
Do not abuse the main unit or JOGPAD.  Avoid strik-
ing, shaking, etc.  It could be damaged by improper
handling or storage.
• Do not use strong or abrasive detergents when
cleaning the unit and JOGPAD.
Do use a dry cloth to clean the unit when dirty.
In case the dirt is hard to remove, use a mild deter-
gent and wipe gently.
• The input power source is 120V AC 60 Hz.
PRECAUTIONS
• Do not expose the main unit and JOGPAD to rain or
moisture, and do not try to operate the equipment in
wet areas.  Do not operate the main unit and JOG-
PAD if it becomes wet.
• Do not attempt to disassemble the main unit or JOG-
PAD.  In order to prevent electric shock, do not
remove screws or covers.
There are no user-serviceable parts inside.
• Do take immediate action if ever the main unit or
JOGPAD should become wet.  Turn the power off
and have the unit checked by an authorized service
facility.
• Do not interrupt the Vent Hole on the front panel.
The main unit will heat and it will cause the damage
or a fire.
• Be sure to remove the plug by grasping the plug
and not the cord itself.
• Do not initial the built-in hard disk. 
						

							3
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
1. S-VGA connector (15 pins)
This connector is used to connect the personal com-
puter monitor via a special cable.
2. Analog I/O cable connector (60 pins)
This connector is used to connect analog video and
analog audio inputs and outputs via a special cable.
3. PCI connector
This connector is used to connect the personal com-
puter.
nVIDEO COMPRESSION BOARD
(TARGA DV2000 BOARD)
1. Channel A (Ch A) connector for external
connections
This connector is used to connect the hard disk box
via a special cable.
2. Channel B (Ch B) connector for external
connections
This connector is used to connect the hard disk box
via a special cable.
3. Channel A (Ch A) connector for internal
connections
This connector is used to connect the hard disk
housed in the personal computer via a flat cable
(accessory) with SCSI board.
4. Channel B (Ch B) connector for internal
connections
This connector is used to connect the hard disk
housed in personal computer via a flat cable (acces-
sory) with SCSI board.
5. PCI connector
This connector is used to connect the personal com-
puter.
nSCSI BOARD
q
q
wewer
t 
						

							4
nJOG BOARD
1. ISA connector
This connector is used to connect the personal com-
puter.
2. Interrupt number (IRQ) setting jumper (P9)
Set the interrupt number (IRQ) where the jumper pin
is inserted.
3. I/O port setting jumper (P12)
Set the I/O address where the jumper pin is inserted.
4. RS422 control connector 1 (RS422-1)
This connector is used to connect a device that can
be controlled through a RS422 interface via the spe-
cial cable (accessory).  This connection can be used
to control recording and playback on a VCR.
5. RS422 control connector 2 (RS422-2)
This connector is used to connect a device that can
be controlled through a RS422 interface via the spe-
cial cable (accessory).  This connection can be used
to control recording and playback on a VCR.
6. JOGPAD connector (JOGPAD)
This connection is used to connect a JOGPAD via
the special cable (accessory).
7. Time code, reference input/output connector
(LTC/REF)
This connector is used to connect, via the special
time code and reference I/O cable (accessory), with
the time code input and output on a VCR, etc., and
with equipment that inputs an external signal for
synched composites (horizontal sync only).•Time code input and output
This connector is used to connect with the time code
input and output on a VCR, etc.  Make this connec-
tion only if the VCR has a time code signal (LTC) out-
put.  The time code output is not a loop-through of
the signal that was input on the time code input.
Ver. 1.0 software does not support time code input
and output.
•Reference input and output
This connector is used to connect with equipment
that inputs an external sync signal.  Be sure to input
the reference signal so as to maintain the frame pre-
cision.  If a reference signal is not input, video audio,
and time code synchronization, and time code I/O
operation, cannot be guaranteed.  The reference
code output is a loop-through of the signal that was
input on the reference input.
8. Reference I/O 75-ohm terminator switch
Be sure to  turn off the switch.
When terminating the reference (REF IN) in 75Wter-
mination, connect the termination (accessory) to the
REF OUT cable.
qw
e
r
t
y
u
i
REF OUT cable
Termination
BCP-PT (accessory)
Coaxial relay plug
BCJ-J (accessory) 
						

							5
01&/

0,6/%0 4)*5
53*.

.0%&
%*7*%&

%&-&5&;
0
0
.
(050 
1
-

:
4
5
0
1
.3,

*/.3,

065

nJOGPAD
qwer t y
u
i
o
!0
!1
!2 !3 !4!5
1. Positioner
Sets the key position.  Is ineffective with Ver. 1.0 soft-
ware.
2. Wipe Lever
Controls the Wipe speed and audio volume.
Is ineffective with Ver. 1.0 software.
3. TRIM / MODE b
Used in Trim mode.
(SHIFT + TRIM/MODE)    Turns Trim mode On/Off.
4. DIVIDE / DELETE a
Deletes a clip.
(SHIFT + DIVIDE / DELETE)    Divides a clip.
5. ZOOM / b
Zooms in the time line
(SHIFT + ZOOM)    Zooms out the time line.
6. GOTO / a
Jumps to the starting or editing mark
(SHIFT + GOTO)    Jumps to the beginning or end of
a sequence.
7. MARK OUT
Sets or cancels the ending mark.
(SHIFT + MARK OUT)   Selects the grip of the OUT
point.8. MARK IN
Sets or cancels the starting mark.
(SHIFT + MARK IN)  Selects the grip of the IN
point.
9. PLAY / STOP
Plays back or stops.
(SHIFT + PLAY /STOP)    Plays back between the
starting and ending marks.
10. Shuttle Ring
Plays back video and audio forward (clockwise) or in
reverse (counterclockwise) with variable speed.
11. JOG Dial
Plays back video and audio forward (clockwise) or in
reverse (counterclockwise) frame by frame.
12. SHIFT
Switches button functions.
13. UNDO
Cancels the immediately previous operation.
14. OPEN / OK
Registers the Log in the Log List (when batch digitiz-
er used).
15. JOGPAD Connector
Connects with the Main Unit by using the JOGPAD
cable (accessory). 
						

							6
nNecessary cables for this system
VGA loop cable 
CA-206
Analog I/O cable
CA-208Cable Use
This cable connects the video compression board and the personal
computer monitor.  This cable is provided with the video compression
board.
This cable connects the video compression board with the DVCPRO
VCR (video, audio), the NTSC monitor, etc.  This cable is provided with
the video compression board.
VCR/JOGPAD cable
E8-163J601This cable connects the JOG board with the JOGPAD and the DVCPRO
VCR (RS422).  This cable is provided with the JOG board.
LTC/REF cable
E9-165J600This cable connects the JOG board with the DVCPRO VCR (Time code
IN/OUT), and the external sync input.  This cable is provided with the
JOG board.
SCSI cable
ACK/M-WPThis cable connects the SCSI board with the hard disk unit.  This cable is
manufactured by Adaptec.
CABLE INFORMATION 
						

							7 VGA loop cable (CA-206)
Connects to the VGA connector
on the video compression board. 
(15-pin male connector)(labelled TARGA DV2000)
Connects to the VGA connector on the computer.
(15-pin male connector)  (labelled VGA)
Connects to the cable for the personal computer monitor.
(15-pin female connector)  (labelled MONITOR)
Analog I/O cable (CA-208)
Cable color
Gray/white
Red
Blue
Black
Green
Gray
Black
Gray/white
Black
Gray
Black
Green
Blue
Red
Brown
Black NO
Q
W
E
R
T
Y
U
I
O
P
{
}
q
w
e
r
tLabel
S-VIDEO IN
R-Y/R IN
B-Y/B IN
CV/CS IN
Y/G IN
R AUDIO IN
L AUDIO IN
S-VIDEO OUT
L AUDIO OUT
R AUDIO OUT
CV/CS OUT
Y/G OUT
B-Y/B OUT
R-Y/R OUT
KEY OUT
REF INConnector
S connector
BNC
BNC
BNC
BNC
XLR
XLR
S connector
XLR
XLR
BNC
BNC
BNC
BNC
BNC
BNC
D-sub 60-pin Signal name
YC input
Component R-Y input
Component B-Y input
Composite input
Component Y input
Audio R channel input
Audio L channel input
YC output
Audio L channel output
Audio R channel output
Composite output
Component Y output
Component B-Y output
Component R-Y output
Not used
Reference signal input
Analog input/output connector
q
w
r e !6
!7
t
y u i o!0
!1!2!3!4!5 
						

							8 VCR/JOGPAD cable
LTC/REF cable
Mini-DIN 8-pin
Mini-DIN 9-pinD-sub 9-pin RS422 control connector on VCR, etc.
VCR, etc.JOG board
[
JOGPAD[
[
Cable color
Red
Green
Blue
BlackLabel
Ref IN
Ref OUT
LTC IN
LTC OUTSignal name
External sync input
Ref IN loop-through
LTC input
LTC output
LTC/REF connector plug No
Q
W
E
R
TPlug shape
BNC
BNC
BNC
BNC
Mini-DIN 9 pin
JOG board[
[
q
w
r e t