Panasonic AY-RP500 Installation Manual

							9
Install the boards in the computer.
There are three boards to be installed:
1. Video compression board (TARGA DV2000 board)
2. SCSI board
3. JOG board [AY-RP500 board (JOG board)]
nPreparation
1. Have a computer with Windows NT installed ready.
Note:Windows NT must be installed on drive C:
(IDE hard disk) which has been formatted using
the NTFS file system.
Note:Before installing Windows NT, decide whether
to use the entire area on the IDE hard disk as
the system area or to partition the drive into two,
namely, the system drive and audio drive.
When the entire drive is to be used as the sys-
tem drive, format it using NTFS and then install
Windows NT.
When the entire drive is to be divided into two
logical drives, the MS-DOS FDISK command,
etc. must be used to partition the disk before
Windows NT is installed.  Then proceed with the
Windows NT installation.
When the drive is to be partitioned, provide at
least 1 gigabyte of memory for the system drive
(where Windows NT will be installed).
2. Turn off the computer.
3. Open the case of the computer.  For details on how
to do so, refer to the instruction manual that was pro-
vided with the computer.
4. Confirm which PCI slot (the white connector on the
motherboard) the video card is installed in.  If the
video card is already in the PCI slot that is the far-
thest from the CPU, you do not need to move the
video card.
5. In all other cases, move the video card according to
the procedure described in steps 6 through 9 below.6. Remove the screws that secure the cover for the PCI
slot that is farthest from the CPU, and then remove
that cover.
7. Remove the screws that secure the cover for the
video card, and then remove the video card.
8. Plug the video card into the PCI slot that is farthest
from the CPU, and secure the cover in place with the
screws.
9. Store the screws and cover that were removed in a
safe place.
BOARD SETUP
SCSI board
TARGA DV2000 board CPU

AY-RP500 board
(JOG board)Video card 
						

							nInstalling the Video Compression
board (TARGA DV2000 board)
Note that due to structural differences, the installation
location may differ depending on the model of computer
used.
1. Remove the cover for the PCI slot (the white connec-
tor on the motherboard) that is closest to the CPU.
Note:The construction of some computers does not
physically allow the TARGA DV2000 board to be
plugged into the PCI slot that is closest to the
CPU.  If this is the case with your computer,
remove the cover for the adjacent PCI slot.
2. Carefully remove the TARGA DV2000 board from its
anti-static protective pack.  If you need to set the
board down, place it on top of this pack.
3. Attach the board spacer to the main board (the
longest board) among the TARGA DV2000 boards.
(Refer to the diagram below.)
The board spacer comes in two types (metal and
plastic) but only one type is enclosed with the unit.
1.)  Board spacer (metal type)
nBIOS Setup
1. This procedure sets up the motherboard BIOS.
2. Open the BIOS setup screen. (The method of calling
up the BIOS setting screen varies depending on the
computer.  Refer to the users manual of the comput-
er.)
3. Set Plug & Play OS to OFF. (The setting on your
computer system may be Disable or No.)
4. Set Power Management to OFF. (This may be
Disable or NO.)
5. Save the settings, and quit the BIOS setup screen.
The computer starts up automatically.
6. Once the computer has started up, confirm that it is
operating normally; then quit Windows NT and turn
off the computer.
Insert the main board
into the grooves in the
rail guides on the board
spacer.Grooves in the rail guides
on the board spacer. Main board
10 
						

							11
Insert the video compression board with board spacer attached.The rail guides
on the personal
computer
Illustration of the video compression board inserted into PC
2.)  Board spacer (plastic type)
4. Plug the TARGA DV2000 board into the PCI slot that
is closest to the CPU (or the next closest slot, if the
board will not physically fit into the closest slot, it is
depends on the computer used).  Here, firmly mount
the board spacer between the guide rails on the per-
sonal computer.  The assembly diagram shown
below is intended as an example. The actual con-
nection locations may differ depending on the model
of computer used.Connect the ground wire to the computers chassis
(metal portion) only when the metal type of board spacer
is supplied.
Then use the twist-tab wire to secure the board spacer to 
the guide rails inside the computer.
The installation of the AY-PB500 board (TARGA DV2000
board) will differ depending on the computer used.
Refer to the appendix.
Chassis 
(metal portion)
Connect the ground wire of the video compression board (board
spacer) to the chassis (metal portion) of the system unit. (Unscrew
the screw and then use it to secure the wire in place.)
Guide rails
Twist-tab wire Grooves in the rail guides
on the board spacer.
Main board
Ground wire
Board spacer 
						

							9. Follow the instructions to install the driver from the
CD-ROM.  Operate according to the procedures
below.
1)  The window for Truevision TARGA DV2000 Setup
appears.
Click .
2)  The Product Type Inquiry window appears.
Select the type of board to use, and click  .
For analog type, select TARGA DV2000 (default).
For SDI type, select TARGA DV2000 SDX.
For SDI Voyager 2, select TARGA DV2000 SDX V2.
(When the type is selected,     is displayed.)
Refer to Appendix (The type of the SDI board)
about the type of the board.
3)  The Choose Destination Location window apears.
Click .
4)  The Select Program Folder window appears.
Click .
5)   Installation begins.
6)  The Readme window appears.
Click    on the upper-right of the window and
close it.
7)  The Installation Completed Successfully window
appears.
Select Yes, I want to restart my computer now.
(When this is selected,     is displayed.) 
Click .
10. Restarts after installation.
At this point, remove the CD-ROM from which the
driver was installed.
11. When Windows NT has restarted, click  .
From Programs in the Start Menu, click
Administrative Tools 
pWindows NT
Diagnostics. The program starts up.Start
Finish
Next
Next
Next
Next
12
5. Connect the CA-206 cable that was provided with
the TARGA DV2000 board.  Plug the connector
labelled TARGA DV2000 into the connector on the
TARGA DV2000 board, plug the connector labelled
VGA into the connector on the video card, and con-
nect the connector labelled MONITOR to the moni-
tor cable.
See page 7 and 32 for the VGA loop cable (CA-206).
6. Store the screws and cover that were removed in a
safe place.
7. Turn on the power and start up Windows  NT.
8. Insert the software package CD-ROM into the CD-
ROM drive.  Click  .
Click Run on the start menu.  The Run window
now opens.
Input CD-ROM drive name:	arga\disk1\setup.exe
in Open: and click OK.  If, for instance, the CD-
ROM drive is drive d:, input the series of character
as shown above.
To check the letter assigned as the CD-ROM drive,
click My Computer.  The CD-ROM drive letter will
appear on the screen.Start 
						

							13
12. The Windows NT Diagnostics Program window
appears.
Click the Resources label.  The resource list shown
below appears (not in the same layout).
Note:DVRNTDRV indicates the TARGA DV2000
board.  Check which number is used for the
IRQ.  
After checking, click  to close the window.
13. Change the display driver.
1)  Click  .  Select Settings in the Start Menu.
The Control Panel opens.  Then double-click
Display.
2)  Select Settings from Display Properties and
click .
3)  Click  in Display Types.
4)  Click  in Display Modification.
5)  The directory of the display driver is to be
opened, so enter 
c:\TARGA2KVD\WINNT\Display and click  .
6)  Confirm that Truevision DVR Display is dis-
played on the screen and click  .
7)  The message The drivers were successfully
installed appears.  Click  .
OK
OK
OK
Have Disk
Change
Display Types
Start
OK
8)  Click  in Display Types.
9)  Click  in Screen Properties.
10)  The message You must restart your computer...
appears.  Click  .
11)  Windows NT starts up.  When the Control Panel
opens, close it.
When the message A new graphics driver has
been installed appears, click  .
12)  Click and drag the mark on the frame of the
desktop area in Screen Properties to adjust it for
the resolution of 1152 x 870 pixels.  Here, confirm
that the font size is Small Fonts, and that the
Refresh Frequency is 75 Hz.
13)  Click  , and click  to enter test mode.
The test screen appears.
14)  If the test screen is displayed correctly, click
.
15)  Click  in Display Properties to close this
screen.  The resolution will change.
Note:Be sure to modify the display and test it.
Otherwise, the display will not be correct.OK
Yes
OKTest
OK
Yes
Close
Close 
						

							14
nInstalling the SCSI board
1. Remove the cover for the PCI slot (the white connec-
tor on the motherboard) that is adjacent to the slot
where the TARGA DV2000 board is plugged in (on
the side away from the CPU).
2. Carefully remove the SCSI board from its anti-static
protective pack.  If you need to set the board down,
place it on top of this pack.
3. Plug the SCSI board into the PCI slot adjacent to the
TARGA DV2000 board on the side away from the
CPU, and secure the cover in place with the screws.
4. Store the screws and cover that were removed in a
safe place.
5. For details on the cable connections, refer to the
hard disk setup procedure.   (Do not fail to connect
the cables.)
6. Turn on the power and start up Windows NT.
7. Click  .  Click  in the Start Menu.  The
Control Panel opens.  Then click SCSI Adapters.
8. Select Driver and click  .
9. The manufacturer and the SCSI adapter list appear.
Select Adaptec for the manufacturer, and 
AHA-294x/AHA-394x or AIC-78xx PCI SCSI con-
troller for the adapter, and click  .
Here, the Windows NT CD-ROM is required, so load
it and click  .
The WIndows NT CD-ROM window opens.  This is
not needed, so click the     on the upper-right of the
window to close it.
10. Specify the directory of the driver.  For example, if
the CD-ROM drive is drive E, enter E:\i386, and click
.
11. When installation is ended, the message You must
restart your computer... appears.  Click  .
Yes
OK
OK
OK
Add
SettingsStart
12. When Windows NT has restarted, click  .
From Programs in the Start Menu, click
Administrative Tools 
pWindows NT
Diagnostics. The program starts up.
13. The Windows NT Diagnostics Program window
appears.
Click the Resources label.  The resource list
appears.
aic78xx indicates the SCSI board.  Check which
number is used for the IRQ.
aic78xx is displayed twice.  Both numbers might
be the same or they might not; it does not matter in
either case.
After checking, click  to close the window.
OK
Start 
						

							15
6. Appear Configuration menu window.
Select Advanced Configuration Options, press
[Enter] key.
7. Appear Advanced Configuration.
Select Support for Ultra SCSI Speed, press [Enter]
key.
8. Appear Disabled , Enabled selectable.
Select Enabled and press [Enter] key.
Confirm Enable in Support for Ultra SCSI Speed.
)
6MUSB6MUSB
8
BU
#VT

$IBOOFM

$POGJHVSBUJPO
4$4*
#VT
*OUFSGBDF
%FGJOJUJPOT
)PTU
EBQUFS
4$4*
*%
 
4$4*
1BSJUZ
$IFDLJOH
 &OBCMFE
)PTU
EBQUFS
4$4*
5FSNJOBUJPO
 VUPNBUJD
EEJUJPOBM
0QUJPOT
#PPU
%FWJDF
0QUJPOT
 1SFTT
&OUFS
4$4*
%FWJDF
$POGJHVSBUJPO
 1SFTT
&OUFS
EWBODFE
$POGJHVSBUJPO
0QUJPOT
 1SFTT
&OUFS


3FTFU
UP
)PTU
EBQUFS
%FGBVMUT
EWBODFE
$POGJHVSBUJPO
0QUJPOT
$IBOOFM

#*04
	$POGJHVSBUJPO
6UJMJUZ
3FTFSWFT
#*04
4QBDF

 



&OBCMFE
4VQQPSU
3FNPWBCMF
%JTLT
6OEFS
#*04
BT
JYFE
%JTLT
 









#PPU
0OMZ
&YUFOEFE
#*04
5SBOTMBUJPO
GPS
%04
%SJWFT


(CZUF
 









&OBCMFE
$IBOOFM

%JTQMBZ
$USM

.FTTBHF
%VSJOH
#*04
*OJUJBMJ[BUJPO
 


&OBCMFE
.VMUJQMF
-6/
4VQQPSU
 



































%JTBCMFE
#*04
4VQQPSU
GPS
#PPUBCMF
$%30.
 























&OBCMFE
#*04
4VQQPSU
GPS
*OUI
&YUFOTJPOT
 























&OBCMFE
4VQQPSU
GPS
6MUSB
4$4*
4QFFE
 




























%JTBCMFE
n Setting the baud rate of the SCSI board
Set the SCSI baud rate of the SCSI board.
Check the model number of the board used, and set the
rate by following the procedure given.
l When AHA-3940UWD is the SCSI board used
1. Power On.
2. Appear next comment when Boot Up.
Adaptec AHA-3940U/3940UW BIOS v1.xx
(c)  199x Adaptec, Inc. ALL Rights Reserved.
>
3. Quickly press [Ctrl]+[A] keys when appear this com-
ment.
4. Run SCSI Utility and appear next window.
Use  arrow  key, select Channel(A or B), and press
[Enter] key.
You must change configuration both Cannel A and B.
5. Appear Menu window.
Select Configure/View Host Adapter Setting, and
press [Enter] key.
)
6MUSB6MUSB
8
BU
#VT$IBOOFM

8PVME
ZPV
MJLF
UP
DPOGJHVSF
UIF
1$*
EFWJDF
PS
SVO
UIF
4$4*
EJTL
VUJMJUJFT 
4FMFDU
UIF
PQUJPO
BOE
QSF@@
&OUFS
1SFTT

UP
TXJUDI
CFUXFFO
DPMPS
BOE
NPOPDISPNF
NPEFT
$POGJHVSF7JFX
)PTU
EBQUFS
4FUUJOHT
4$4*
%JTL
6UJMJUJFT
0QUJPOT
:PV
IBWF
NPSF
UIBO
POF
4$4
DIBOOFM
JO
ZPVS
TZTUFNT
.PWF
UIF
DVSTPS
UP
UIF

CVTDIBOOFM
PG
UIF
POF
UP
CF
DPOGJHVSFE
BOE
QSFTT&OUFS


5PHHMF
DPMPS.POPDISPNF
#$IBOOFM
&OBCMFE
%JTBCMFE 
						

							16lWhen AHA-3940AUWD is the SCSI board
used
1. Power On.
2. Appear next comment when Boot Up.
Adaptec AHA-3940AU/AUW/AUWD SCSI BIOS v1.xx
(c)  199x Adaptec, Inc. ALL Rights Reserved.
>
3. Quickly press [Ctrl]+[A] keys when appear this com-
ment.
4. Run SCSI Utility and appear next window.
Use  arrow  key, select Channel(A or B), and press
[Enter] key.
You must change configuration both Cannel A and B.
5. Appear Menu window.
Select Configure/View Host Adapter Setting, and
press [Enter] key.
:PV
IBWF
BO
)66868%
4$4*
IPTU
BEBQUFS
JO
ZPVS
TZTUFN
.PWF
UIF
DVSTPS
UP
UIF
CVTEFWJDFDIBOOFM
PG
UIF
POF
UP
CF
DPOGJHVSFE
BOE
QSFTT
&OUFS


5PHHMF
DPMPS.POPDISPNF&
&##VT%FWJDFDIBOOFM
)66868%
BU
#VTI
%FWJDF&I
$IBOOFM 

4$4*
EJTL
VUJMJUJFT 

4FMFDU
UIF
PQUJPO
BOE
QSFTT

Ð`ðP`0
ðð
1SFTT

UP
TXJUDI
CFUXFFO
DPMPS
BOE
NPOPDISPNF
àP`@ð
$POGJHVSF7JFX
)PTU
EBQUFS
4FUUJOHT
4$4*
%JTL
6UJMJUJFT
0QUJPOT
9. Press [ESC] key 2 times, appear next message.
Select Yes, press [Enter] key.
Finish for channel A.
10. Press [ESC] key.
Select channel B and change same as channel A.
11. Finish setting for channel B(finish Item 9), press
[ESC] key 2 times.
Appear message of finish.
Select Yes, and press [Enter] key. 
12. Appear Please press any key to reboot, press
any key.
Setting is finish and auto reboot.
&YJU
6UJMJUZ 
:FT
/P
4BWF
$IBOHFT
.BEF 
:FT
/P 
						

							17
6. Appear Configuration menu window.
Select SCSI Device Configuration, and press
[Enter] key.
7. Appear Device configuration window.
In all SCSI ID (from #0 to #15) ,Change 40.0(from
20.0) at Maximum Sync Transfer Rate.
At Each SCSI ID ,move cursor to 20.0 and press
[Enter] key.
Appear all useable number, select 40.0 and press
[Enter] key.
Please change about all SCSI ID.
)66868%
BU
#VTI
%FWJDF&I
$IBOOFM 
$POGJHVSBUJPO
4$4*
#VT
*OUFSGBDF
%FGJOJUJPOT
)PTU
EBQUFS
4$4*
*%
 
4$4*
1BSJUZ
$IFDLJOH
 &OBCMFE
)PTU
EBQUFS
4$4*
5FSNJOBUJPO
 VUPNBUJD
EEJUJPOBM
0QUJPOT
#PPU
%FWJDF
0QUJPOT
 1SFTT
&OUFS
4$4*
%FWJDF
$POGJHVSBUJPO
 1SFTT
&OUFS
EWBODFE
$POGJHVSBUJPO
0QUJPOT
 1SFTT
&OUFS


3FTFU
UP
)PTU
EBQUFS
%FGBVMUT
4$4*
%FWJDF
$POGJHVSBUJPO
4$4*
EFWJDF
*%        
*OJUJBUF
4ZOD
/FHPUJBUJPO ZFT ZFT ZFT ZFT ZFT ZFT ZFT ZFT
.BYJNVN
4ZOD
5SBOTGFS
3BUF        
&OBCMF
%JTDPOOFDUJPO ZFT ZFT ZFT ZFT ZFT ZFT ZFT ZFT
*OJUJBUF
8JEF
/FHPUJBUJPO ZFT ZFT ZFT ZFT ZFT ZFT ZFT ZFT
0QUJPOT
-JTUFE
#FMPX
)BWF /0
&&$5
JG
UIF
#*04
JT
%JTBCMFE
4FOE
4UBSU
6OJU
$PNNBOE OP OP OP OP OP OP OP OP
#*04
.VMUJQMF
-6/
TVQQPSU OP OP OP OP OP OP OP OP
*ODMVEF
JO
#*04
4DBO ZFT ZFT ZFT ZFT ZFT ZFT ZFT ZFT
4$4*
EFWJDF
*%        
*OJUJBUF
4ZOD
/FHPUJBUJPO ZFT ZFT ZFT ZFT ZFT ZFT ZFT ZFT
.BYJNVN
4ZOD
5SBOTGFS
3BUF        
&OBCMF
%JTDPOOFDUJPO ZFT ZFT ZFT ZFT ZFT ZFT ZFT ZFT
*OJUJBUF
8JEF
/FHPUJBUJPO ZFT ZFT ZFT ZFT ZFT ZFT ZFT ZFT
0QUJPOT
-JTUFE
#FMPX
)BWF /0
&&$5
JG
UIF
#*04
JT
%JTBCMFE
4FOE
4UBSU
6OJU
$PNNBOE OP OP OP OP OP OP OP OP
#*04
.VMUJQMF
-6/
TVQQPSU OP OP OP OP OP OP OP OP
*ODMVEF
JO
#*04
4DBO ZFT ZFT ZFT ZFT ZFT ZFT ZFT ZFT
8. When finish to change about all SCSI ID, press
[ESC] key 2 times.
Appear confirmation message.
Select Yes, and press [Enter] key.
Finish for channel A.
9. Press [ESC] key.
Select channel B and change same as channel A.
10. Finish setting for channel B(finish Item 8), press
[ESC] key 2 times.
Appear message of finish.
Select Yes, and press [Enter] key.
11. Appear Please press any key to reboot, press any
key.
Setting is finish and auto reboot.
4BWF
$IBOHFT
.BEF 
:FT
/P
&YJU
6UJMJUZ 
:FT
/P 
						

							18
nInstalling the AY-RP500 board
(JOG board)
1. Remove the cover from the ISA slot (the black con-
nector on the motherboard) that is the farthest away
from the CPU.
2. Carefully remove the AY-RP500 board (the JOG
board) from its anti-static protective pack.  If you
need to set the board down, place it on top of this
pack.
3. Use the jumper pins to set the IRQ and the I/O port.
The permitted settings for the IRQ are 3, 4, 5, and 7;
the permitted settings for the I/O port are 230H,
240H, 330H, and 340H.
For IRQ, insert the jumper pin into jumper P9 and
set. (See item 2, page 4.)
•To set 3 as the IRQ:
•To set 4 as the IRQ:
•To set 5 as the IRQ:
•To set 7 as the IRQ (Factory setting) :For the I/O port, insert the jumper pin into jumper
P12 and set. (See item 3,  page 4.)
•To set 230H as the I/O address
(Factory setting):
•To set 240H as the I/O address:
•To set 330H as the I/O address:
•To set 340H as the I/O address:
Since the JOG board uses IRQ and I/O port exclu-
sively, be certain to set a number that are not used
by any other device.  
Confirm settings of other devices using the Windows
NT diagnostic program (page 19).
Note on IRQ Settings :
5 and 7 are recommended.
If 5 and 7 are being used by another device,
set either 3 or 4.  Because 3 and 4 are nor-
mally used for serial ports (COM1, COM2),
either 3 or 4 must be disabled in the BIOS
settings. (Set to Disable etc.)   In this case,
only one serial port can be used.
For details on how to set the BIOS, refer to the
instruction manual that was provided with your
computer.
p Push in the jumper pin here.8      8
8      8
8      8
8      8IRQ3
IRQ4
IRQ5
IRQ7
p Push in the jumper pin here.
8      8
8      8
8      8
8      8IRQ3
IRQ4
IRQ5
IRQ7
p Push in the jumper pin here.
8      8
8      8
8      8
8      8IRQ3
IRQ4
IRQ5
IRQ7
p Push in the jumper pin here.
8      8
8      8
8      8
8      8IRQ3
IRQ4
IRQ5
IRQ7
Do not push in jumper pins.8      8
8      8
8      8P 1
P 2
P 3
p Push in the jumper pin here.8      8
8      8
8      8P 1
P 2
P 3
p Push in the jumper pin here.
8      8
8      8
8      8P 1
P 2
P 3
p Push in the jumper pin here.
p Push in the jumper pin here.
8      8
8      8
8      8P 1
P 2
P 3