Panasonic AY-RP500 Installation Manual

							39
To use the system, the application program on the CD-
ROM supplied with the software package must be
installed on the hard disk.  This requires a keyboard,
mouse, and personal computer monitor.
nSetting Up the Virtual Memory
This procedure sets up the virtual memory to operate the
application program.
DVEdit Setting
Drive C: Initial Size 300MB
Maximum Size 400MB
Do not expand the virtual memory in a wrong drive.
Otherwise it is not assured that the DVEdit works
properly.
1. Open the Control Panel.2. Double-click the icon System.
3. Click the  button.
Change
LOADING SOFTWARE PACKAGE 
						

							40
4. Click C: .
5. Enter 300 in the box for initial size and 400 in the box
for maximum size. 6. Click the  button.
Confirm that the top window shows 300-400.  Then,
click  on this panel.
7. Click and restart.
Yes
OK
Set 
						

							41
nInstall an Application Program
1. Connect the keyboard, mouse, and personal com-
puter monitor to the personal computer, and turn on
the power switches on the peripheral equipment and
then on the personal computer.  Windows NT starts
up.
2. Insert the CD-ROM supplied with the software pack-
age into the CD-ROM drive.
3. Click .
Click Run on the start menu.  The Run window
now opens.
4. Input CD-ROM drive name:\dvedit\disk1\setup.exe
in Open: and click  .  If, for instance, the CD-
ROM drive is drive d:, input the series of character
as shown above.
To check the letter assigned as the CD-ROM drive,
click My Computer.  The CD-ROM drive letter will
appear on the screen.
5. The Welcome window appears.
Click .
6. The User Information window appears.
Name:. . . . .  Enter your name.
Company:. .  Enter your companys name.
Serial:. . . . .  Enter the product ID number printed
on the label affixed to the case of the
CD-ROM.  Input all eight letters and all
eight digits (and do not omit the -).
When all items have been entered,
click .
Next
Next
OK
Start
7. The Choose Destination Location window appears.
Click .
8. The TARGA Product Information window appears.
Select the type of video compression board to use,
and click  .
For analog type, select TARGA DV2000.
For SDI type, select TARGA DV2000 SDX.
For SDI Voyager 2, select TARGA DV2000 SDX V2.
(When the type is selected,     is displayed.)
Refer to Appendix (The type of the SDI board) about
the type of the board.
9. The A/V Hard Disk Information window appears.
Enter the number of hard disk drives for video use.
To select two hard disk drives for video use, enter 2
at the Drives: prompt.
To select four hard disk drives for video use, enter 4
at the Drives: prompt.
After entering the number of drives, click  .
Note:Here, two or four hard disks can be set for
video use.  To use more hard disks, start up the
application after setting it up, and use a utility.
10. The A/V Hard Disk Information window is still dis-
played.
Enter the name of the hard disk drives for video use.
To select two hard disk drives for video use:
Enter O: at the Drive 1: prompt, and click .
Enter P: at the Drive 2: prompt, and click .
To select four hard disk drives for video use:
Enter O: at the Drive 1: prompt, and click .
Enter P: at the Drive 2: prompt, and click .
Enter Q: at the Drive 3: prompt, and click .
Enter R: at the Drive 4: prompt, and click .
11. The A/V Hard Disk Information window is still dis-
played.
Enter the name and directory of the hard disk drives
for audio use.  The default is g for the drive name,
and audiopools for the directory.  Just modify the
drive name.
For example, to select drive d for the hard disk drive
for audio use, enter d:\audiopools.  Then click  .
Next
Next
Next
Next
Next
Next
Next
Next
Next
Next 
						

							42
12. The Black Level Information  window appears.
Select the setup level to be used and click  .
(When the setup level is selected,     is displayed.)
13. The DVEdit JOGPAD board Information window
appears.
Set the I/O address of the JOG board to be used.
Select the value of the jumper setting of the JOG
board, and click   . (When the value is selected,
is displayed.) (The default is 230H)
14. The DVEdit JOGPAD board Information window is
still displayed.
Set the IRQ No. of the JOG board to be used.
Select the value of the jumper setting of the JOG
board, and click  . (When the value is
selected,      is displayed.) (The default is IRQ7)
15. The Select Program Folder window appears.
Click .
16. The Start Copying Files window appears.
The settings list appears.  Confirm the contents and
click .
17. Installation begins.
18.  When installation ends, the Setup Complete window
appears.
Select Yes, I want to restart my computer now.
(When this is selected,   is displayed.) Click 
.
The computer will restart.
19. The Shortcut DVEdit is created.Finish
Next
Next
Next
Next
NextnInstalling Fonts
1. Open the Control Panel, and double-click the Fonts
icon.  The Fonts panel appears.
2. Insert the software package CD-ROM into the CD-
ROM drive.
3. Click Install New Font in File on the Menu bar
(above the window)  The Add Font panel appears.
4. Select the CD-ROM drive in Drives:.  Double-click
the font (English font) or fontjp (Japanese font) direc-
tory in Folders. 
5. Click  or the name of the font to be
installed.  Then click  .
The contents of the CD-ROM will be installed in
Windows NT.
6. Activate an application, and double-click Special in
the Tool Box.  The Setup panel appears.
7. Double-click Font Setup in the Setup panel.
Select the required font from List of Windows Fonts
and click .  The font will be installed in the
application.Append
OK
Select All 
						

							43
This manual describes the procedures for upgrading
DVEdit to the newest software.  
Observe the following procedures to correctly replace
the existing software.
After replacing the Targa driver, be sure to replace, or
write over, the existing software.  
Otherwise, normal operation cannot be expected.
nPrecautions for Version-up
lTarga Driver
The new Targa driver cannot be written over the old
driver to upgrade the version.  First, remove the old
driver from DVEdit by uninstalling, then install the new
Targa driver to upgrade the version.  After replacing the
Targa driver, be sure to reinstall (or overwrite) DVEdit.
lDVEdit Software
In upgrading the DVEdit software version, the new
software can be written over the old software.  Different
from the Targa driver, it is not necessary to uninstall the
old software.
Overwrite permits use of the existing A/V data as it is
even after upgrading the version.  If the new software is
installed after uninstalling the existing software, all the
data will be erased for a new setup.
lPrecautions
The following two cases can be considered in installing
the new software in DVEdit.
Carefully replace the existing software by observing the
version-up procedures for each of the three cases
described in the following section. 
1. Erasing data from DVEdit already in use
2. Not erasing data from DVEdit already in use
nUpdating Procedures
lErasing Data from DVEdit Already in Use
1. Virtual Memory Expansion
Observe the manual Setting up the Virtual Memory to
properly expand the virtual memory.
2. Confirming the Version Installed
(a) Confirming the version of the Targa driver in use
Confirm the version of the Targa driver installed in
DVEdit at present.  This can be confirmed on the DVR
Information panel.  Click Start, Program, TARGA
DV2000 and DVRInfo to call this panel on the
screen.  Watch the Software tag, referring to the
figures below.  The version is shown in the Product
Version line at the top.
VERSION-UP PROCEDURES FOR DVEdit 
						

							44
(b) DVEdit software version
The DVEdit version panel appears when the About
menu on the Special panel is clicked.
3. Confirming the CD-ROM Version
The version of the newest software written on the CD-
ROM is written in d:¥version.txt in the CD-ROM drive.
(The case where the CD-ROM drive is d:¥ is described
below.) 
Compare the version of the Targa driver and that of the
DVEdit software.  If they are the same, neither needs to
be replaced.  If the Targa driver version is the same, skip
items 3 and 4 and proceed to items 5 and 6.
Description of Targa driver replacement:  Items 4 and 5
Description of software replacement:        Items 6 and 74. Uninstalling the Old Targa Driver
(a) Select Program, Targa DV2000 and uninstall
Targa DV2000 ... from Start.  This starts uninstalling
the Targa driver.
(b) Click  under the dialog shown.
(c) The following panel appears and click the 
button when uninstall is completed.
OK
Yes 
						

							45
(d) If the following message appears during uninstall,
click .
( e ) Check disk scheduling
Enter chkdsk /f c: on the command prompt panel.
After that, You will be asked Checkdisk
scheduling(Y/N)?
So enter y on the command prompt panel. 
This executes the check-disk in restarting. 
( f ) Restart. (The check- disk automatically runs at restart.)
Select Shutdown from Start.
Add a check mark to Restart Computer and click
.
(g ) Directory delete
If c:¥TARGA2KDV and subsequent directories remain
in Explorer after restart, delete all together with the
directories.
Yes
No to All
5. Installing the New Targa Driver
( a ) Installing the Targa driver
Insert a CD-ROM into the CD-ROM drive. (The case
where the CD-ROM drive is d:¥ is described below.)
Move the cursor to the Run command in the Start
menu and click the command.  The Run window will
be displayed.  Type the  command,
d:¥Targa¥disk1¥setup.exe in the Open field of the
Run window and click the  button.  This starts
the Targa installer, so start installing as instructed on
the panel.  The subsequent operations are the same
as installing a Targa driver for the first time.  Start
installing according to the instructions on the panel
shown.
After install is completed, the panel asks whether or
not to restart, so restart as shown on the panel.
(b) After restart, double-click the icon Display on the
control panel.
(c) Select Settings from Display Properties and click
.
Display Type
OK 
						

							46
( d ) Click  in Display Type. 
( e ) Click  in Display Modification.
( f ) The directory of the display driver is to be opened,
so enter
C:¥TARGA2KDV¥WINNT¥Display and click  .
( g ) Confirm that Truevision DVR Display is displayed
on the screen and click  .
( h ) The message The drivers were successfully
installed appears.  Click  .
( i ) Click  in Display Types
( j ) Click  in Screen Properties
( k ) The message You must restart your computer
888
appears.  Click  .
( l ) Windows NT starts up.  When the Control Panel
opens, close it.
When the message A new graphics driver has been
installed appears, click  .
( m ) Click and drag the mark on the frame of the desktop
area in Screen Properties to adjust it for the
resolution of 1152 x 870 pixels.  Here, confirm that
the font size is small and that the Refresh Frequency
is 75 Hz.
( n ) Click  , and click  to enter test mode.  The
test screen appears.
( o ) If the test screen is displayed correctly, click  .
( p ) Click  in Display Properties to close this
screen.  The resolution will change.
OK
Yes
OKTest
OK
Yes
Close
Close
OK
OK
OK
Have Disk
Change6. Uninstalling Old DVEdit
( a ) Select Set and Control Panel from Start to call the
Control Panel on the screen.
Double-click the icon Add/Remove Programs on the
Control Panel.  Select Panasonic DVEdit on the
Application Add/Remove Properties panel and click
the Add/Remove .  This uninstalls the
DVEdit already installed.
Add/Remove 
						

							47
(b) Restart
Select Shutdown from Start.
Add a check mark to Restart Computer and click
.
( c ) Directory Delete
If c:¥DVEdit and subsequent directories remain in
Explorer after restart, delete all the files together with
the directories.  If e:¥audio, e:¥Title and subsequent
directories remain, similarly delete all the files
together with the directories. (The audio-storing drive
characters may be different and there may be two or
more audio/title storing drives depending on the
case.  In such a case, delete the above for all the
drives.)
7. Installing new DVEdit
Insert a CD-ROM into the CD-ROM drive.  (The case
where the CD-ROM drive is d:¥ is described below.)
Move the cursor to the Run command in the Start menu
and click the command.  The Run window will be
displayed.  
Type the command, d:¥dvedit¥disk1¥setup.exe in the
Open field of the Run window and click the  button.
This starts the DVEdit installer, so start installing as
instructed on the panel.  The subsequent operations are
the same as installing DVEdit for the first time.  Start
installing according to the instructions on the panel
shown.
After install is completed, the panel asks whether or not
to restart, so restart as shown on the panel.  When the
icon DVEdit on the deskstop is double-clicked after
restart, the new version of DVEdit is ready for use.
OK
Yes
lNot Erasing Data from DVEdit Already in Use
In upgrading the DVEdit software version, the new
software can be written over the old software.  Overwrite
permits use of the existing A/V data as it is even after
upgrading the version.
1. Virtual Memory Expansion
Observe the manual Setting up the Virtual Memory to
properly expand the virtual memory.
2. Confirming the version installed
(a) Confirming the version of the Targa driver in use
Confirm the version of the Targa driver installed in
DVEdit at present.  This can be confirmed on the DVR
Information panel.  Click Start, Program, TARGA
DV2000 and DVRInfo to call this panel on the
screen.  Watch the Software tag, referring to the
figures below.  The version is shown in the Product
Version line at the top. 
						

							48
(b) DVEdit software version
The DVEdit version panel appears when the About
menu on the Special panel is clicked.
3. Confirming the CD-ROM version
The version of the newest software written on the CD-
ROM is written in d:¥version.txt in the CD-ROM drive.
(The case where the CD-ROM drive is d:¥ is described
below.) 
Compare the version of the Targa driver and that of the
DVEdit software.  If they are the same, neither needs to
be replaced.  If the Targa driver version is the same, skip
items 4 and 5 and proceed to items 6.
Description of Targa driver replacement:  Items 4 and 5
Description of software replacement:        Items 64. Uninstalling the Old Targa Driver
(a) Select Program, Targa DV2000 and Uninstall
Targa DV2000 ... from Start.  This starts uninstalling
the Targa driver.
(b) Click  under the dialog shown.
(c) The following panel appears and click the 
button when uninstall is completed.
OK
Yes