Panasonic AY-RP500 Installation Manual

9
Install the boards in the computer.
There are three boards to be installed:
1. Video compression board (TARGA DV2000 board)
2. SCSI board
3. JOG board [AY-RP500 board (JOG board)]
nPreparation
1. Have a computer with Windows NT installed ready.
Note:Windows NT must be installed on drive C:
(IDE hard disk) which has been formatted using
the NTFS file system.
Note:Before installing Windows NT, decide whether
to use the entire area on the IDE hard disk as
the system area or to partition the drive into...

nInstalling the Video Compression
board (TARGA DV2000 board)
Note that due to structural differences, the installation
location may differ depending on the model of computer
used.
1. Remove the cover for the PCI slot (the white connec-
tor on the motherboard) that is closest to the CPU.
Note:The construction of some computers does not
physically allow the TARGA DV2000 board to be
plugged into the PCI slot that is closest to the
CPU.  If this is the case with your computer,
remove the cover for the...

11
Insert the video compression board with board spacer attached.The rail guides
on the personal
computer
Illustration of the video compression board inserted into PC
2.)  Board spacer (plastic type)
4. Plug the TARGA DV2000 board into the PCI slot that
is closest to the CPU (or the next closest slot, if the
board will not physically fit into the closest slot, it is
depends on the computer used).  Here, firmly mount
the board spacer between the guide rails on the per-
sonal computer.  The assembly...

9. Follow the instructions to install the driver from the
CD-ROM.  Operate according to the procedures
below.
1)  The window for Truevision TARGA DV2000 Setup
appears.
Click .
2)  The Product Type Inquiry window appears.
Select the type of board to use, and click  .
For analog type, select TARGA DV2000 (default).
For SDI type, select TARGA DV2000 SDX.
For SDI Voyager 2, select TARGA DV2000 SDX V2.
(When the type is selected,     is displayed.)
Refer to Appendix (The type of the SDI board)
about the type...

13
12. The Windows NT Diagnostics Program window
appears.
Click the Resources label.  The resource list shown
below appears (not in the same layout).
Note:DVRNTDRV indicates the TARGA DV2000
board.  Check which number is used for the
IRQ.  
After checking, click  to close the window.
13. Change the display driver.
1)  Click  .  Select Settings in the Start Menu.
The Control Panel opens.  Then double-click
Display.
2)  Select Settings from Display Properties and
click .
3)  Click  in Display Types.
4)...

14
nInstalling the SCSI board
1. Remove the cover for the PCI slot (the white connec-
tor on the motherboard) that is adjacent to the slot
where the TARGA DV2000 board is plugged in (on
the side away from the CPU).
2. Carefully remove the SCSI board from its anti-static
protective pack.  If you need to set the board down,
place it on top of this pack.
3. Plug the SCSI board into the PCI slot adjacent to the
TARGA DV2000 board on the side away from the
CPU, and secure the cover in place with the screws....

15
6. Appear Configuration menu window.
Select Advanced Configuration Options, press
[Enter] key.
7. Appear Advanced Configuration.
Select Support for Ultra SCSI Speed, press [Enter]
key.
8. Appear Disabled , Enabled selectable.
Select Enabled and press [Enter] key.
Confirm Enable in Support for Ultra SCSI Speed.
)
6MUSB6MUSB
8
BU
#VT

$IBOOFM

$POGJHVSBUJPO
4$4*
#VT
*OUFSGBDF
%FGJOJUJPOT
)PTU
EBQUFS
4$4*
*%
 
4$4*
1BSJUZ
$IFDLJOH
 &OBCMFE...

16lWhen AHA-3940AUWD is the SCSI board
used
1. Power On.
2. Appear next comment when Boot Up.
Adaptec AHA-3940AU/AUW/AUWD SCSI BIOS v1.xx
(c)  199x Adaptec, Inc. ALL Rights Reserved.
>
3. Quickly press [Ctrl]+[A] keys when appear this com-
ment.
4. Run SCSI Utility and appear next window.
Use  arrow  key, select Channel(A or B), and press
[Enter] key.
You must change configuration both Cannel A and B.
5. Appear Menu window.
Select Configure/View Host Adapter Setting, and
press [Enter] key....

17
6. Appear Configuration menu window.
Select SCSI Device Configuration, and press
[Enter] key.
7. Appear Device configuration window.
In all SCSI ID (from #0 to #15) ,Change 40.0(from
20.0) at Maximum Sync Transfer Rate.
At Each SCSI ID ,move cursor to 20.0 and press
[Enter] key.
Appear all useable number, select 40.0 and press
[Enter] key.
Please change about all SCSI ID.
)66868%
BU
#VTI
%FWJDF&I
$IBOOFM 
$POGJHVSBUJPO
4$4*
#VT
*OUFSGBDF
%FGJOJUJPOT
)PTU
EBQUFS
4$4*
*%
...

18
nInstalling the AY-RP500 board
(JOG board)
1. Remove the cover from the ISA slot (the black con-
nector on the motherboard) that is the farthest away
from the CPU.
2. Carefully remove the AY-RP500 board (the JOG
board) from its anti-static protective pack.  If you
need to set the board down, place it on top of this
pack.
3. Use the jumper pins to set the IRQ and the I/O port.
The permitted settings for the IRQ are 3, 4, 5, and 7;
the permitted settings for the I/O port are 230H,
240H, 330H, and 340H....