Panasonic AY-RP500 Installation Manual

19
Note on I/O port settings:
Make sure that the following I/O ports do not
overlap so that the JOG board can perform 10-
bit address decoding.
• Generally speaking, 0240-024F and 0F40-0F4F are
often allocated to a Sound Blaster board.
4. Insert the JOG board into the ISA slot that is the far-
thest away from the CPU.  At this point, insert each
special cable securely into the LTC/REF connector
and the RS422-1 connector.  After positioning them,
secure the cover in place using the screws.
5. Store the...

20
There are two different methods for hard disk setup.One
is for installing a hard disk inside the personal computer,
and one is for using an external hard disk unit (optional).
nWhen installing a hard disk inside the
personal computer
lSCSI ID Setting
Set the SCSI IDs as shown below.   0 is recommended.
When setting another number and using an optional hard
disk box, make sure that none of the SCSI IDs are dupli-
cated.
Note:Set SCSI ID to other than 7.
HARD DISK SETUP
lTermination Setting
Set the...

21 Installing the disk in a 3.5-inch bay
Use the screws (inch screws) provided to install the
drive.
Installing the disk in a 5-inch bay
Use the brackets and screws (inch screws) provided to
install the drive.  (Refer to the diagram below.)
Hard disk bracket Inch screws
When bracket attached
lMounting and connecting the hard disk
drive
1. Take off the front panel of the personal computer.
The assembly diagram shown below is intended as
an example.  The actual connection locations may
differ depending on...

22
3. Insert the hard disk, and attach it with screws (in four
places).
The assembly diagram shown below is intended as
an example.  The actual connection locations may
differ depending on the model of computer used.
When installing another hard disk unit, remove the
expansion bay brackets, insert the hard disk, and
then secure it in place with screws.  then secure it in
place with screws (in four places).  (Refer to the dia-
gram below).
The assembly diagram shown below is intended as
an example.  The...

23
When connecting two or more hard disk boxes
When connecting two or more hard disk boxes, 
AY-CA68SR3 SCSI cables (sold separately) are needed.
Connect the SCSI OUT connector on the first hard disk
box to the SCSI IN connector on the second hard disk
box.  When doing so, connect the channel A on the first
hard disk box to channel A on the second hard disk box,
and connect channel B on the first hard disk box to chan-
nel B on the second hard disk box.  Connect a third and
subsequent hard disk boxes in...

24
n Checking the hard disk
Check the hard disk.
This operation must be done when the hard disk is incor-
porated in the computer or hard disk unit.
Check the model number of the board used, and check
the hard disk by following the procedure given.
lWhen AHA-3940UWD is the SCSI board used
1. Power On.
2. Appear next comment when Boot Up.
Adaptec AHA-3940U/3940UW BIOS v1.xx
(c)  199x Adaptec, Inc. ALL Rights Reserved.
>
3. Quickly press [Ctrl]+[A] keys when appear this com-
ment.
4. Run SCSI Utility and...

25lWhen AHA-3940AUWD is the SCSI board
used
1. Power On.
2. Appear next comment when Boot Up.
Adaptec AHA-3940AU/AUW/AUWD SCSI BIOS v1.xx
(c)  199x Adaptec, Inc. ALL Rights Reserved.
>
3. Quickly press [Ctrl]+[A] keys when appear this com-
ment.
4. Run SCSI Utility and appear next window.
Use  arrow  key, select Channel(A or B), and press
[Enter] key.
5. Appear Menu window.
Select SCSI Disk Utilities, and press [Enter] key.
Check the connected SCSI devices.
:PV
IBWF
BO
)66868%...

26
6. Appear a list of the connected SCSI devices.
(When ST34371W made by SEAGATE is connected to
ID=1)
If the devices actually connected are at variance
with what is listed, a wrong connection, SCSI ID set-
ting error, terminal setting error or defective hard
disk may be to blame.  Press [ESC] key to exit.
First, check the connections and the SCSI ID and
terminal settings.  If the message remains, a defec-
tive hard disk may be to blame.  
If what is listed matches with the devices actually
connected,...

27
nSetting up the hard disk
It must be set up so that the hard disk can be used.
1. Turn on the power, and start up Windows NT.
2. Click .
From Programs in the Start Menu, click
Administrative Tools 
pDisk Administrator.
The program starts up.
3. When the Disk Administrator starts up, a list appears
showing the bulk-storage devices such as hard
disks and CD-ROM.
4. The contents displayed are as follows:
Disk 0:Always the IDE drive.
Disk 1 and after:
SCSI hard disks connected to Channel A, in
order from...

28
11.  In Tools on the menu bar, click Format.
12.  The format window opens.  Click    of File system,
and select NTFS.
13.  Do not set the format option.  No guarantee is made
for the operation if Quick format is selected for for-
matting.  The regular formatting facility must be
used.
14.  Click  .  The warning display appears, but
click .
15.  When the message Format complete appears, click
.  Then, click  in the format window.
The format window will close.
16. In Tools on the menu bar, click Assign...