OKI MC860dn User Manual

							
Specifications > 171
Network SpecificationConnectivity Ethernet 100Base-TX/10Base-T auto-negotiation  with RJ-45 connector
Network protocol TCP/IP: Network layer - ARP, IP, ICMP, IPv6
Transport layer - TCP, UDP
Application layer - LPR, FTP, TELNET, HTTP, IPP, 
DHCP/BOOTP, SMTP, WINS, SNMPv1/v3
NetBEUI:
SMB, NetBIOS
Netware:
Remote printer mode (max. 8 print servers)
Print server mode (max. 8 file server, 32 queues)
Encrypted password support (in print server mode)
NetWare6J/5J/4.1J (NDS, boundary)
SNMP
ETHERTALK:
ELAP, AARP, DDP, AEP, NBP, ZIP, RTMP, ATP, PAP 
IEEE802.1X
IEEE802.1X:
EAP-TLS, PEAP
Supported browsers Microsoft IE 4.1 or higher Netscape Navigator 4.0 or higher
Configuration 
requirement IP address 
Subnet mask
Gateway
SMTP server/POP3 server
FTP server
Web server
Fax Specification Circuits PSTN, PBX line
Compatibility Super G3 and G3
Transmission speed Under 3 sec (Super G3); 6 sec (G3)
Line interface Dual RJ -11C (Line and TEL)
Compression method MH, MR, MMR, JBIG
Memory backup 72 hours (after 48 hours full-charge)
Image data memory 16 Mb (ITU-T; 1024 A4 sheets)
Send capacity Max. Tabloid (A3) width Max. 35.4 inches (900 mm) length
Resolution:
Standard
Fine
Photo
Extra fine 203 x 98 pi
203 x 196 dpi
203 x 196 dpi
406 x 392 dpi
Speed dials 500
ITEMSPECIFICATION
Downloaded From ManualsPrinter.com Manuals 
						

							
Specifications > 172
Group dial 32 groups
Auto redial Yes
Sender ID Yes (max. 22 characters)
Transmission:
Broadcast Yes (max. 530 transmissions)
Delayed Yes (up to 100 transmissions; up to one month from current date/time)
F code Yes, using ITU standard sub address and pass code
F code polling Yes, using ITU stan dard sub address and pass code
PC fax Yes, from a pc application via fax driver
Receive:
Memory Yes, receives even when printer error or paper out  situation occurs
Remote Yes
F code Yes, using ITU standard sub address and pass code
Polling Yes
F code polling Yes, using ITU stan dard sub address and pass code
E-mail Specification Communication protocol SMTP, MIME, POP3
File formats:
 B&W
 Grey/Colour PDF, TIFF
PDF, TIFF, JPEG, XPS 
Default file format PDF
Resolution 75, 100, 150, 200, 300, 400, 600 dpi
Default resolution 200 dpi
Address book volume:
Max. e-mail addresses
Group 500
32
Multiple recipients allow Yes
Security check Yes
Mail server 
authentication SMTP, POP3
Supported mail server 
application Lotus Mail Server 5.0
MS Exchange Server 2000
RedHat 7.0 SendMail
Supported LDAP server Windows 2000 Active Directory Windows NT 4.0 + MS Exchange 5.5
Lotus Notes R5
ITEMSPECIFICATION
Downloaded From ManualsPrinter.com Manuals 
						

							
Specifications > 173
Supported mail 
applicationMicrosoft Outlook 2000
Microsoft Outlook Express 5.0
Microsoft Outlook Express 6.0
Netscape Messenger 4.7
Netscape Messenger 4.73
Eudora 4.3.2J
Lotus Notes R5
Filing Specification Communication protocol FTP, HTTP, CIFS
File formats:
 B&W
 Grey/colour PDF, TIFF
PDF, TIFF, JPEG, XPS
Default file format PDF
Resolution 75, 100, 150, 200, 300, 400, 600 dpi
Default resolution 200 dpi
Max. number of profiles 50
Printing Speed 26 pages per minute colour 34 pages per minute monochrome
Resolution 600 x 600 dpi 600 x 1200 dpi 
Optical: 600 x 600 dpi
Memory 512 MB standard, upgradeable to 768 MB max.
Paper capacity at 
20-lb. US Bond 
(75 g/m²)  300 sheets in main tray
100 sheets in multi purpose tray
530 sheets in optional 2nd tray
530 sheets in optional 3rd tray
Paper weight Minimum, all trays: 17 lb. US Bond (64 g/m²)  Maximum:
• Main Tray: 32 lb. US Bond (120 g/m²) 
• MP Tray: 53 lb. US Bond (200 g/m²) 
• Optional Trays 2 and 3: 47 lb. US Bond (176g/m²) 
Paper output 250 sheets in face down (top) stacker @ 
						

							
Specifications > 174
This device is not intended for use at visual display workplaces in compliance with 
BildscharbV.
Image drum life 20,000 pages at 3 pages per job
Belt life 80,000 letter pages at 3 pages per job
Fuser life 100,000 letter pages
ITEMSPECIFICATION
Downloaded From ManualsPrinter.com Manuals 
						

							
Appendix A - Moving and transporting > 175
Appendix A - Moving and transporting
Moving Your System
1.Enable mirror carriage transfer mode:
(a) Press the  SETUP button on th e control panel.
(b) On the touch screen, press  Admin Setup.
(c) Enter the administrator password and press  Enter.
(d) Press  User Install .
(e) Press the arrow symbol twice to vi ew page 3 of the User Install screen.
(f) Press  Mirror Carriage mode .
(g) At the prompt, press  Yes to confirm.
(h) If necessary, remove plugs (1) from  the scanner lock locations as shown.
(i) Using the tool provided (2), lock th e scanner at the two locations as shown.
1
2
Downloaded From ManualsPrinter.com Manuals 
						

							
Appendix A - Moving and transporting > 176
(j) On the touch screen, press Close.
(k) Press the  SETUP button on th e control panel.
(l) On the touch screen, press  Shutdown.
(m) On the touch screen, press  Yes to confirm shutdown.
2. Turn off the MFP and disconnect or remove the following:
• Power cord, earth wire
•Printer cable
• Paper in the paper cassette
3. Move the MFP to the new location.
WARNING!
This product is heavy; a minimum of  three people are required to 
lift it safely. 
NOTE
Be sure to unlock the scanner before turning on the MFP after transportation 
and then disable the mirror carriage transfer mode.
Downloaded From ManualsPrinter.com Manuals 
						

							
Appendix A - Moving and transporting > 177
Transporting Your System 
1.Enable mirror carriage transfer mode:
(a) Press the  SETUP button on th e control panel.
(b) On the touch screen, press  Admin Setup.
(c) Enter the administrator password and press  Enter.
(d) Press  User Install .
(e) Press the arrow symbol twice to vi ew page 3 of the User Install screen.
(f) Press  Mirror Carriage mode .
(g) At the prompt, press  Yes to confirm.
(h) If necessary, remove plugs (1) from  the scanner lock locations as shown.
WARNING!
Your MFP is a precision machine and can be damaged during 
transportation if packaged incorrectly.
NOTE
If your machine is equipped with the  additional paper tray(s) and cabinet, 
remove these before transporting. Refer to “Additional Paper Trays and 
Storage Cabinet” on page 137; the removal process is the reverse of the 
installation procedure.
1
Downloaded From ManualsPrinter.com Manuals 
						

							
Appendix A - Moving and transporting > 178
(i) Using the tool provided (2), lock the scanner at the two locations as shown.
(j) On the touch screen, press  Enter.
(k) Press the  SETUP button on th e control panel.
(l) On the touch screen, press  Shutdown.
(m) On the touch screen, press  Yes to confirm shutdown.
2. Turn off the MFP and disconnect or remove the following:
• Power cord, earth wire
•Printer cable
• Paper in the paper cassette
3. Pull the lever (a) firmly to release the lo ck and then gently raise the scanner (b).
2
b
a
Downloaded From ManualsPrinter.com Manuals 
						

							
Appendix A - Moving and transporting > 179
4.Press the cover release (a) and open the top cover (b) fully.
5. Lift each of the image drum units out of  the MFP and place them on a flat table.
6. Tape each junction of the image drum and toner cartridges with vinyl tape (1).
7. Re-install the image drum units back into the MFP.
8. Close the top cover and press down firm ly so that the cover latches closed.
WARNING!
If the MFP has been powered on, the  fuser will be hot. This area is 
clearly labelled. Do not touch.
CAUTION!
The green image drum surface at the base of each cartridge is very 
delicate and light sensitiv e. Do not touch it and do not expose it to 
normal room light for more than  5 minutes. Never expose the drum 
to direct sunlight or very bright room lighting.
b
a
1
Downloaded From ManualsPrinter.com Manuals 
						

							
Appendix A - Moving and transporting > 180
9.Gently lower the scanner.
10. Protect the MFP with cushion  pads and put it in a box.
NOTE
It is recommended that you use the original box and packaging if available.
WARNING!
This product is heavy; a minimum of  three people are required to 
lift it safely. 
NOTE
Be sure to unlock the scanner before turning on the MFP after transportation 
and then disable the mirror carriage transfer mode.
Downloaded From ManualsPrinter.com Manuals