OKI C130n User Manual
Here you can view all the pages of manual OKI C130n User Manual. The Oki manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 41
41 - C130n User’s Guide Interface Menu With this menu, interface settings can be specified. The printer must be rebooted after any setting in the ETHERNET menu (for example, the TCP/IP address) is changed. Therefore, the following message appears when the configuration menu is exited (the + key is repeatedly pressed) after a setting has been changed. Select YES, and then press the Enter key to reboot the printer. Otherwise, turn off the printer, and then turn the printer on again after a few...
Page 42
42 - C130n User’s Guide NoteIf MAIN MENU /SYSTEM DEFAULT /SECURITY /CONFIG /ENABLE is set to ON, the administrator password must be entered to display this menu. For details on the default administrator password, refer to “SYSTEM DEFAULT” on page 46. Downloaded From ManualsPrinter.com Manuals
Page 43
43 - C130n User’s Guide Interface Menu NoteAll factory default values are shown in bold. ETHERNETTCP/IPENABLESettingsYES/NO If YES is selected, TCP/IP is enabled. If NO is selected, TCP/IP is disabled. IPV4DHCP/ BOOTPSettingsYES/NO Select whether or not the IP address is automatically acquired. If YES is selected, the IP address is automatically acquired. If NO is selected, the IP address is not automatically acquired. IPV4 ADDRESSSettings192.168.001.002 Set the IPv4 address for this printer on the...
Page 44
44 - C130n User’s Guide ETHERNET (cont.)ENABLE AUTO IPSettingsYES/NO Select whether or not the IPv4 address is automatically acquired when DHCP/BOOTP and PING, ARP are not functioning or when there is no response. If YES is selected, the IP address is automatically acquired. If NO is selected, the IP address is not automatically acquired. IPV6ENABLESettingsYES/NO If YES is selected, IPv6 is enabled. If NO is selected, IPv6 is disabled. IDENTIFIERDisplays the Link-Local address. ENABLE...
Page 45
45 - C130n User’s Guide ETHERNET (cont.)IPX/SPXFRAME TYPESettingsAUTO, 802.2, 802.3, ETHER II, SNAP Specify the protocol used with NetWare. ETHERNE T SPEEDSettingsAUTO, 100 FULL DUPLEX, 100 HALF DUPLEX, 10 FULL DUPLEX, 10 HALF DUPLEX Specify the transmission speed for the network and the transmission method for bi-directional transmission. DISABLE 802.1XSettingsYES, NO If YES is selected, IEEE802.1x function is enabled. If NO is selected, IEEE802.1x function is disabled. PS PROTOCOL SettingsBINARY,...
Page 46
46 - C130n User’s Guide SYSTEM DEFAULT With this menu, settings can be specified to adjust the operation of the printer, such as the time until the machine enters Energy Saver mode. System Default Menu Tree PRINT QUALITY COLOR MODE EMULATIONS > DEFAULT > AUTO DEFAULT > POSTSCRIPT - ERROR PAGE > PCL - LINE TERMINATION - FONT • PITCH SIZE • FONTNUMBER • POINT SIZE • SYMBOL SET STARTUP OPTIONS > START PAGE DATE & TIME ENERGY SAVER SECURITY > CONFIG - ENABLE FORMAT > FLASH - SET USER PASSWD RESTORE/SAVE >...
Page 47
47 - C130n User’s Guide NoteIf MAIN MENU /SYSTEM DEFAULT /SECURITY /CONFIG /ENABLE is set to ON, the administrator password must be entered to display this menu. System Default Menu NoteAll factory default values are shown in bold. PRINT QUALITYSettingsHIGH, STANDARD Select the image quality for prints. COLOR MODESettingsCOLOR, GRAYSCALE Specify whether printing is in full color or grayscale. NoteThe color mode setting specified from the printer driver has priority over the setting specified...
Page 48
48 - C130n User’s Guide EMULA- TIONS DEFAULTSettingsAUTOMATIC, POSTSCRIPT, PCL5, PCL XL, HEX DUMP Specify the printer control language. If AUTOMATIC is selected, the printer automatically selects the printer control language from the data stream. AUTO DEFAULTSettingsPCL5, POSTSCRIPT Select the printer description language when it cannot be identified from the data. POSTSCRIP TERROR PA G ESettingsON, OFF Select whether or not an error page is printed when a PostScript error occurs. PCLLINE TERMINA...
Page 49
49 - C130n User’s Guide STARTUP OPTIONSSTART PA G ESettingsYES, NO Select whether or not a startup page is printed when the printer is turned on. If YES is selected, the startup page is printed when the printer is turned on. If NO is selected, the startup page is not printed. DATE & TIMESettingsyyyymmdd:hhmmss Set the date and time on the time-of-day (TOD) clock. The settings appear in the following order: year, month, day:hour, minutes, seconds. ENERGY SAVERSettings15 MINUTES, 30 MINUTES,1 HOUR,2...
Page 50
50 - C130n User’s Guide SERVICE MENU With this menu, the service representative can adjust the printer and perform maintenance operations. This menu cannot be accessed by the user. SECURITY (cont.)SET ADMIN PASSWDSettings: the last four digits of the printer serial number Specify the administrator password for displaying the administrator menus. The specified password is applied only if MAIN MENU/SYSTEM DEFAULT/SECRITY/ CONFIG/ENABLE is set to ON. The password can contain a maximum of 16...