Oce PlotWave 300 User Manual

Scan a CAD drawing to TIFF format
1.Feed the original face up and centered on the original feeding table.
Note:
You do not need to center the original precisely. The exact position of the original is au-
tomatically detected by the scanner.
2.Select 'Scan' on the user panel.
Chapter 3 - Quick start
71
Scan a CAD drawing to TIFF format
Downloaded From ManualsPrinter.com Manuals   

Note:
The description of the first default scan template is displayed ('CAD to TIFF'). With a
scan template you can pre-define the settings you need for a scan job. You only need to
set the job settings once and you can store the settings in a job template that is presented
on the user panel. You can re-use the job template for each next job without the need to
redefine all the settings every time. (see ‘Define the scan job preferences and scan templates’
on page 133).
3.Press the green button....

Scan a CAD drawing to color PDF
1.Feed the original face up and centered on the original feeding table.
Note:
You do not need to center the original precisely. The exact position of the original is au-
tomatically detected by the scanner.
2.Select 'Scan' on the user panel.
3.Open the 'Scan' tab with the confirmation button above the scroll wheel.
4.Use the scroll wheel to select scan template 2 ('CAD to color PDF').
Chapter 3 - Quick start
73
Scan a CAD drawing to color PDF...

Note:
With a scan template you can pre-define the settings you need for a scan job. You only
need to set the job settings once and you can store the settings in a job template that is
presented on the user panel. You can re-use the job template for each next job without
the need to redefine all the settings every time. (see ‘Define the scan job preferences and
scan templates’ on page 133).
5.Press the green button.
Note:
Depending on the selected 'Original release mode' in the Océ Express...

Scan a CAD drawing to a USB mass storage device
1.Feed the original face up and centered on the original feeding table.
Note:
You do not need to center the original precisely. The exact position of the original is au-
tomatically detected by the scanner.
2.Select 'Scan' on the user panel.
3.Open the 'Scan' tab with the confirmation button above the scroll wheel.
4.Use the scroll wheel to select scan template 3 ('CAD to USB').
Chapter 3 - Quick start
75
Scan a CAD drawing to a USB...

Note:
With a scan template you can pre-define the settings you need for a scan job. You only
need to set the job settings once and you can store the settings in a job template that is
presented on the user panel. You can re-use the job template for each next job without
the need to redefine all the settings every time. (see ‘Define the scan job preferences and
scan templates’ on page 133).
5.Press the green button.
Note:
Depending on the selected 'Original release mode' in the Océ Express...

Switch off the printing system
1.Use the on / off button at the front side of the printer to switch off the printing system.
The lighted button starts to blink.
Note:
You can also use the 'Shut down' button in the Océ Express WebTools.
Attention:
Wait until the on / off button stops blinking.
Chapter 3 - Quick start
77
Switch off the printing system
Downloaded From ManualsPrinter.com Manuals        

2.Switch off the power switch at the rear side of the printing system (A).
Chapter 3 - Quick start
78
Switch off the printing system
Downloaded From ManualsPrinter.com ManualsA
B       

Chapter 4
Define your workflow
with the Océ Express
WebTools
Downloaded From ManualsPrinter.com Manuals 

Introduction
The Océ Express WebTools
Introduction
The Océ Express WebTools is an application that runs embedded on the Océ PlotWave
300. You can use an Internet browser (Microsoft® Internet Explorer 6.0 (or higher) or
Mozilla Firefox™ 2.0 (or higher) to open the home page of the Océ Express WebTools.
Definition
You can use the Océ Express WebTools to do the following.
■Send print jobs to your Océ PlotWave 300 with Océ Publisher Express.
■Access the settings to manage the configuration and preferences of...