Nortel Modular Ics 6.0 Installer Guide

Lines / 341
P0992638 03Modular ICS 6. 0 Installer Guide
Trunk modeInstaller password required
Trunk mode allows you to specify either disconnect 
supervision or unsupervised. Disconnect supervision, also 
referred to as loop supervision, releases an external line when 
an open switch interval (OSI) is detected during a call on that 
line. This prevents the line from remaining unavailable for 
other Norstar users.
Press CHANGE
 to select the setting: Unspr or Super.
Unspr (the default) turns disconnect...

342 / Lines
Modular ICS 6.0 Installer GuideP0992638 03
Ans with DISAInstaller password required
When activated, the Answer with DISA setting specifies that a 
trunk is answered with stutter dial tone. This feature is only 
active if Ans Mode is set to Auto.
Press CHANGE
 to select the setting: Y (Yes) or N (No). 
To program DISA on PRI trunk, see Programming Direct 
Inward System Access (DISA) on PRI trunks on page 64.
Tips - If loop start lines are set to Auto, you will require an 
E&M card for the DTMF...

Lines / 343
P0992638 03Modular ICS 6. 0 Installer Guide
Link at CO (loop trunks only)Installer password required
Some exchanges respond to a Link signal (²àÚ) by 
providing an alternative line for making outgoing calls. 
When Link at CO is set to Y (Yes), the system applies the 
restrictions on outgoing calls to the digits dialed after the 
Link signal, and the call on the alternative line will be 
subject to all restrictions. 
Setting Link at CO to N (No) prevents a Link signal from 
resetting the...

344 / Lines
Modular ICS 6.0 Installer GuideP0992638 03
Full AutoHoldInstaller password required
Full AutoHold on idle line is a variation of the Automatic Hold 
feature. If you select an idle line, but do not dial any digits, that 
line is automatically placed on hold if you select another line. 
Press CHANGE
 to select the setting: N (No) or Y (Yes).
The line you first selected is held until you press the line 
button. The line is not available for use by anyone else . 
LossPkg
Installer password...

Lines / 345
P0992638 03Modular ICS 6. 0 Installer Guide
The following table describes the five types of loss pa ckages.
Signal
Installer password required
Select the signal type for the line. 
Press CHANGE
 to select one of these settings: WinkStart, 
Immediate, DelayDial.
Loss
PkgReceive
LossTransmit
LossImpedance Distance to switch/
cable loss/terminating 
switch
ShortCO0 dB 3 dB Short Short/2 dB and 6 dB/ICS to CO
ShortPBX 0 dB 0 dB Short Short/2 dB/ICS to PBX
Tips - This setting applies only to lines...

346 / Lines
Modular ICS 6.0 Installer GuideP0992638 03
ANI NumberInstaller password required
Select whether the telephone number of the caller will be 
collected for this line. The digits can then be displayed on 
Norstar telephones as part of Call Display services. 
Press CHANGE
 to select either: N (No) or Y (Yes). 
DNIS Number
Installer password required
Select whether the digits dialed by an external caller on this 
line will be collected. 
Press CHANGE
 to select either: N (No) or Y (Yes).
Tips -...

Lines / 347
P0992638 03Modular ICS 6. 0 Installer Guide
GainInstaller password required
Select the appropriate gain level for the line. 
Press CHANGE
 to select either: Normal or High. 
The default value Normal induces zero loss. Use it when the 
E&M trunks are connected to facilities that present 0 dBm at 
the interface, for both the transmit and receive paths.
Normal gain level (0dBm)
The value High induces 7 dB of loss in the receive path and 
16 dB of loss in the transmit path. Use it when the E&M...

348 / Lines
Modular ICS 6.0 Installer GuideP0992638 03
Programming distinctive ring patternsInstaller password required
When lines are configured on your system, they can be 
assigned one of four distinctive ring patterns (DRP). The 
default for all telephones is 1; the default for lines is None, 
which is the lowest priority.
Call ringing: When multiple calls are presented to the 
telephone, the call with the highest priority DRP setting will be 
the call that rings at the telephone. 
Call answering:...

Lines / 349
P0992638 03Modular ICS 6. 0 Installer Guide
4. Press ‘ until the display shows Lines.
5. Press ‘. The display shows Linexxx:Line XXX.
6. Press FIND
 and enter the line to which you want to define 
a ring pattern.
7. Press ≠ until the display shows TrunkType:PRI.
8. Press ‘ until the display shows Dstnct ring: 
NONE.
9. Press CHANGE
 to toggle to the ring pattern number you 
want to assign to the line (None, 2, 3, 4).
10. Press ¨ to exit or ‘ to continue programming.
Name
The default name for...

350 / Lines
Modular ICS 6.0 Installer GuideP0992638 03
Restrn filters
Restriction filters are groups of dialing restrictions and dialing 
overrides for external numbers or feature codes. By packing a 
set of restrictions and overrides in one group, you can assign 
them to a line in one step, as a single package.
You can make changes to restriction filters under both 
Terminals&Sets, and Lines. Any changes will take affect 
for any telephone, line, or line on a telephone, regardless of 
where the...