Nortel Modular Ics 6.0 Installer Guide

Startup programming / 301
P0992638 03Modular ICS 6. 0 Installer Guide
Startup programming
After the hardware has been installed and powered up, use 
Startup to initialize the system, and select the system template 
that best suits your system.
Performing Startup
1. Enter the Startup access code from a programming set, by 
pressing  which is the 
same as ²¥¥à¡Ûà¡¡à.
To be accepted, the Startup code must be entered no later 
than 15 minutes after the Norstar system has been powered 
up. 
If 15 minutes have...

302 / Startup programming
Modular ICS 6.0 Installer GuideP0992638 03
Changing the default template
After entering the Startup access code and Installer password 
the set displays Reset memory?.
1. Press YES
 to select a default template. 
The display shows the current template.
2. Press CHANGE
 to choose the appropriate template. 
Changing the starting DN 
You can change the starting number for your telephone 
directory numbers (DNs). This is helpful when your system is 
part of a network and you want to...

Startup programming / 303
P0992638 03Modular ICS 6. 0 Installer Guide
3. Enter the new directory number you want as the starting 
DN, and press OK
. 
The display shows the new range of DN numbers.
4. Press ‘ to store the programming. 
The display shows Applyng template. 
This process takes a few minutes. When it is complete, the 
indicators begin to flash. When the set displays Jan 1 1:00 am. 
the initialization is complete.
The length of the directory number that you enter sets the 
length for all...

304 / Programming
Modular ICS 6.0 Installer GuideP0992638 03
Programming
When Startup is complete, use programming to change default 
settings, as required. Use the programming record to orient 
yourself within the programming menus.
Programming for both MICS 6.0 and MICS-XC 6.0 has the 
following main headings:
Terminals&SetsAllows you to assign settings to each 
telephone.
LinesAllows you to assign settings to each 
trunk, external and target line.
ServicesAllows you to create services such as 
night...

Programming / 305
P0992638 03Modular ICS 6. 0 Installer Guide
*For information about programming for Companion, see the 
Modular ICS Companion Installer Guide.
Entering programming for installers
1. Enter the installer codes on a programming set by pressing 
²¥¥‚¯öìéí, 
which is the same as ²¥¥ÛßßÜÝÝ. 
The display shows Password:.
2. Enter the Installer password. 
The default password is 
CONFIG (266344). 
The display shows Terminals&Sets. Three triangular 
indicators º appear on the vertical display...

306 / Programming
Modular ICS 6.0 Installer GuideP0992638 03
Entering programming for system coordinators
The person on staff who is in charge of making changes on the 
Norstar system is called the system coordinator. The everyday 
programming done by system coordinators is described in the 
Modular ICS 6.0 System Coordinator Guide.
Some system coordinators need to be able to program more 
advanced settings and functions in order to carry out the day-
to-day requests and upkeep of the Norstar. These...

Programming / 307
P0992638 03Modular ICS 6. 0 Installer Guide
Entering programming using other passwords
A set of the most often-used headings and subheadings is 
available by using a System Coordinator password. Refer to 
page 281. This level of access is designed for the average user 
who takes care of the day-to-day changes to the Norstar 
system, but who is not interested in more advanced 
programming. The default password is 
ADMIN (23646).
There is also a Basic password that can be used to perform...

308 / Terminals&Sets
Modular ICS 6.0 Installer GuideP0992638 03
Terminals&Sets
Terminals&Sets allows you to assign settings to each 
telephone.
This is the first heading that appears after you enter your 
password.
1. Press ≠.
The prompt displays: Show set: 
2. Enter the set number of the telephone you would like to 
program.
3. Press COPY
 to duplicate the programming for the telephone 
and apply it to another telephone, a range of telephones or 
all the telephones on the system.
For more information...

Terminals&Sets / 309
P0992638 03Modular ICS 6. 0 Installer Guide
Line assignment
This setting allows you to assign physical trunks and target 
lines to each telephone. Target lines are assigned and removed 
in the same manner as other lines. 
1. After you have chosen a set number, press ≠ and 
enter the line number. 
2. Press CHANGE
 to change the setting for each line to one of 
the following: Unassigned, Ring only, Appr&Ring, and 
Appr only. 
Sets that are grouped together, and that are assigned...

310 / Terminals&Sets
Modular ICS 6.0 Installer GuideP0992638 03
Appearances
This setting only applies for direct inward dial (DID) digits 
mapped onto target lines.”
The Norstar system can handle simultaneous calls to a set with 
multiple target line appearances (157 to 284 for MICS, 157 to 
348 for XC). The number of target line appearances depends 
on the line assignment setting, which include: Appr&Ring, 
Ring only, and Appr only.
If Appr&Ring or Appr only is chosen, you can have as many 
simultaneous...