Norstar Compact 616 Dr5 Installer Guide

34  Programming
Set Copy
Use this for copying System data (programming) or System and
User Administration data (Personal programming) from one
telephone to another. System data is programmed in
Configuration and Administration. User Administration
programming is performed by the user at the individual
telephone, and allows the telephone to be customized according
to the user’s requirements.
Set Copy Options
 data
When this message appears on the display, you can choose to
copy System data.
When this...

  
Set Copy characteristics which can NOT be copied
 
  options
 Log     
 Directory  
    
 Private line appearances
Prime telephone designation for a line
 Direct-dial telephone designation
 Extra-dial telephone designation
 Control telephone designation for a line
Service mode Ringing telephone designation for a line
 Receive tones
 Logging set designation
 Show external Voice Message
 Log space
 First display
Compact  Installer Guide 

36  Programming
Characteristics which CAN be copied
Except for those characteristics previously listed, all telephone
related settings can be copied to a destination telephone,
overriding any previous programming. Listed below are the
System level settings and User Administration settings which can
be copied.
System settings in Configuration programming
2.Line 
Line assignment
Answer 
Ringing line preference
Line pool access
Number of Intercom buttons
Prime line designation 

Programming  37
System settings in Administration programming
5.  
 Set Filter
  
 Full handsf ree
 Wandsfree answerback
 pickup group
 Paging
 Auxiliary ringer
 Direct-Dial
 Forward on busy
 Forward on no answer
 Receive tones
 Priority call
9.  Services
  Vmsg
 settings
if desired, the following Personalized settings can be copied
along with the System data:
 Programmable button assignments (Internal Autodial,
External Autodial, and feature access)
 Language choice
 Personal Speed Dial entries
Compact...

38  Programming
Using Set Copy
You can only enter Set Copy through the Configuration access
code and with the Installer password.
Entering Set Copy
After   appears on the display:
1.Press  twice.
The display shows 
C. Set COPY.
2. Press  to go to COPY:  data.
Chart 11 Set Copy
C. Set cowD. Uersion
COPY:  data
Enter  pad digits
Back
. 

Testing the  and 
   external lines by selecting each line in turn at one
of the  and verifying the  tone. If you do 
get a  tone; plug a single-line  into the
 line at the distribution panel. If you still do not get a
dial tone, check all your wiring or contact your telephone
company.
2.Check all internal connections by calling each 
telephone from another  telephone.
3. the quality and clarity of all connections. Check for
crackling, static, hums, or any other unusual noise,
4.If there are any...

40  Troubleshooting,
 Terminal Adapter  trouble
 Check the single line telephone connection by using an
installer’s test telephone.
2. Check the connections to the jack. 
 
3. Check the connections to the 
4.Disconnect the  and replace it with a working Not-star
telephone. If the telephone still works properly, this verifies
that the KSU is working properly.
5.Verify that programming has been done as described in the
 Analog Terminal Adapter Installation Card.
6.If the trouble seems to be in the KSU,...

Troubleshooting  41
FeatureProgrammed in:
Ring for a specific line A. Configuration (1.  Data)
Ring ‘for a specific General  (5. Capabilities)
  ___
Service Modes 
Ringer  
    (6, Service Modes)  
 ,
  Installer Guide 

42  Troubleshooting
Cal  Identification Interface
1.Use the Call Information feature on an incoming call to verify
the operation 
of the 
2Check the connections to the Cll. Refer to the
 Installer Card for installation details., 
3.Verify that the programming has been done as described in
the Compact 
 Programming Record and the Compact
 System Coordinator Guide.
4.Verify that you are subscribing to visual Call Display services
from your local telephone company.
5. Replace the 
Dial tone absent (on...

Troubieshooting  43
KSU down
1.Check that the AC power cord is properly connected.
  that the Software Cartridge  seated in its slot.
  is  
3.If AC power  and the LED indicator on the KSU is
OFF, replace the KSU.