Norstar Compact 616 Dr5 Installer Guide

24  Programming
Line Access
Use Line Access to program characteristics for each telephone.
These characteristics establish which lines the telephone may
use.
When you are finished programming the Line Access settings for
a telephone, you may copy those settings to another telephone
by using the COPY display button (or  on the M7208
Telephone) at the 
Show set: prompt.
Entering the telephone to be programmed
Enter any available DN. Default  range from 21 to 36. 
can be later changed to a new number in...

Programming  25
Answer 
Up to four buttons on a telephone can be programmed for
answering calls to the  of other telephones. The default is
No Answer 
 .
For ‘each line assigned’ to a telephone; you can determine
whether incoming, calls will ring at the telephone. Possible
settings are Ring and No Ring. The default setting is Ring.
Line pool access
You can determine which Line Pool each telephone has access
to. Possible settings are Yes and No. The default setting is No
for each of the three line pools,...

26  Programming
 Prime line
You can assign the Prime line for each telephone. The Prime line
is the first line to be automatically provided at a telephone when
you make a call. The appropriate Prime line will depend on the
customer’s requirements. The default setting is None, which
means that no Prime line is assigned to the telephone. Other
possible settings are an external line (Line number), Line Pool A,
Line Pool 
 Line Pool C or intercom(I/C).
A Prime line is not related to the operation of a Prime...

Programming  27
Call Handling
Use Call Handling parameters to program system-wide
characteristics for certain call features. These characteristics are
not associated in programming with any particular line or
telephone.
Held reminder
Choose if the Held Line Reminder feature is to be active for 
external lines. Possible settings are Yes and No. The default
setting is No. If Yes, the programming menu takes you to the
Remind delay setting.
Remind delay
Assign the delay (in seconds) before the Held Line...

28  Programming
Transfer callback
Choose the delay (number of rings) before a transferred external
call will callback to the originating telephone. The possible delay
is 3, 4, 5, 6, or 12 rings. The default delay is 3 rings.
To estimate the delay time in seconds, multiply the number
of rings by six.
Park prefix
Park prefix assigns a one digit code number to retrieve a parked
call. The default Park prefix is 1. Any digit from 0 to 9, or none,
can be assigned, providing it is not the first digit of a DN or...

Programming  29
Chart  Call Handling
  
 i  1 l neouoII show  :
Headiig  ,__
Held reminder: N
 
Back
Remind delay: 
Next
IBack
 
DRT 3
 ,
 l N”
 Prefix: 1 I
Park timeout: 45
Next
 ,
 timeout: 45 
 
Directed 
 hold:
Tones 
Compact  Installer Guide 

30  Programming
Miscellaneous
Use Miscellaneous settings to program various system-wide
characteristics. These characteristics are not associated in
programming with any particular line or telephone.
Background Music
Choose if the Background music feature is to be available within
the 
 system. Possible settings are Yes and No. The
default setting is No.
If this feature is enabled, ensure that an external music
source has been connected to the KSU. (This music source
is also used for the Music on Hold...

Programming  
If new telephones are being installed at the same time that
other telephones are being relocated; you should perform
the following procedure to ensure that Set Relocation occurs:
Select Yes to  ON Set Relocation. 
2.Unplug the telephone that is to be relocated.
3.Plug the telephone into its new location.
4.Plug a new telephone into the old  of the
telephone that was moved.
Host delay
Host delay programs the delay in milliseconds between the
selection of an outgoing line and the moment that...

32  Programming
Installer password
This allows you to change the Installer password for access to
Configuration programming. The possible setting is any
combination of one to six letters or numbers. The default Installer
Password is       which is the same as 
The default password is required to first gain access to
Configuration programming. However, it is advisable to
change that password to a new one.
Chart 9 Miscellaneous
4. aneousSrsten Data1
Back
Direct-dial  
Next
Sack
Link time:
Set rel  N
Back...

Programming  33
System Data
Use this to change the internal number or Directory Number (DN)
of an individual telephone.
Do not attempt internal number changes within two
minutes of System 
 ,
   
Enter the appropriate internal number when you are prompted for
the old and the new internal number, A message will appear on
the display if either internal number is invalid. The possible
settings are any valid internal number 
 20 and 99. There
is no default setting.
No internal number changes occur until the...