Norstar Compact 616 Dr5 Installer Guide

4  Installing the 
--
 External    wiring   
  lines
 
1.Cross-connect the external lines from the distribution panel
directly to the modular jacks located on the left side of the
KSU. Line 1 is connected to the bottom jack. (Each jack is
identified with its 
2.Route the line cords on the KSU (Figure 3).
Connecting internal wiring
1.Plug the  cable into the KSU (Figure 
2.Route the cable to the distribution panel.
3.Connect the wires to the appropriate pins on the internal
distribution block. (For...

Installing the KSU  5
Internal wiring chart
Chart   Internal Wiring:
 Distribution Block
PinWire ColorServiceTelephone, Port
(Defaults)
26while-BlueT1
1
27while-orangeT2
2Orange-White
26White-GreenT3
3Green-White
29While-BrownT4
4&own-White
305
31Red-BlueT6
6Blue-Red
32T7
7
33T6
6
T99
35T1010
36T1111Blue-Black
37T1212A
 
T13
39T14
14
40Slack-SlateT15
41T1616A
42Yellow-Orange
Spare
17
Orange-Yellow
16Green-Yellow
44
19
45Yellow-Slate20
46Vi-BlueSpare21Spare
47Violet-Orange
External Paging22(audio signal)...

6  Installing the KSU
Installing the Emergency Telephone
An optional Emergency Telephone (ET) automatically connects
to Line 1 when the power fails or when power to the KSU is
disconnected.
Note:Use only a standard  single-line telephone for
this purpose.
Installation Procedure
1.Connect the customer supplied Emergency Telephone to the
Emergency Telephone (ET) jack on the lower right hand
comer of the KSU panel.
2.Label the telephone: “Emergency Telephone Only. This
telephone functions only when AC power...

1. Connect the receiver cord  the
telephone modular jack (indicated by the
symbol at right). Route the cord through
the appropriate cord guide in the base of
the telephone.
2.Connect the line cord into the telephone
line modular jack (indicated by the
symbol at right). Route the cord through
the appropriate cord guide.
3.Connect the other end of the line cord into the modular jack
wired from the distribution panel.
4.
When the telephone is connected to the KSU, the telephone
display and indicators flash...

1.
8  installing the  telephones
Installing a wall-mounted telephone
2.
3.
4.
5.
Remove the beveled wall-mounting
base from the back of the telephone.
Grip the telephone, and with your
thumbs, push on the wide edge of the
base to pop it out from the telephone.
Remove the receiver clip from the
wall-mounting base. Install the clip in
the forward lip “of the receiver rest.
Use a screwdriver or similar tool to
remove the center knock-out panel in
the wall-mounting base.
Screw the base to the wall (thin end...

 
 Optional equipment must meet with local regulatory
approval standards.
Auxiliary  (Customer Supplied)
The  KSU provides a control contact to operate an
external ringer. It does not provide ring current or DC voltage.
The ringer relay contacts must 
 more than 50  from a
30 Vdc source.
1.Follow the manufacturer’s installation instructions.
2.Connect the Auxiliary Ringer generator to the 
distribution block as shown in Chart 2  Internal Wiring.
External Music source (Customer Supplied)
This equipment...

  Installing optional equipment
 
,
,  Background   each  can also
be controlled at the telephone: 
External  (Customer Supplied)
The paging system uses the speakers on  telephones
and can also be used with external loudspeakers provided by the
customer. The paging output from the 
 KSU is 775
 across an input impedance of 600 
1.Follow the manufacturer’s installation instructions.
2.Connect the paging system audio input to the 
distribution block as shown in Chart 2  Internal Wiring.
3.Connect the...

Programming a newly installed  system involves the
completion of the following programming steps:’
 System Startup 
 Configuration
 General Administration
Programming overview
System Startup
System Startup is performed only when the system is first
installed. System Startup allows you to  one of three
programming templates: Square, Hybrid, or PBX. Each template
initializes all of the programming data to system wide defaults.
Configuration
Allows programming of basic line and telephone characteristics....

12  Programming
Set Copy
This feature is  to copy  of  system programming
(Configuration and Administration) from on8 
 to
another. 
 programming on individual  can
also 
 copied, but system-level programming will  copied
along with it. Copy appears on  display as  Set COPY
and is  by using  Configuration code.
System Version
System Version  you to not8  version numbers of the
software in the System Processor 
(SP) software, residing in the
Feature Cartridge.
Version numbers can be used to determine...

Programming  13
Chart 3 Programming Overview
5. 
6. Service Modes
The   M7208,  and M7324 Telephones can
be used with the Compact 
 system. Programming is done
with an M7208, M7310, or M7324 Telephone. as shown on the
following page.