Nitsuko Digital System Feature And Terminal Programming Manual

Table 2-6, 3-DIGIT TABLE PROGRAM RECORD FORM
 
3-DIGIT
CODE1+CODE
SEL # CODE
SEL #
SYSTEM IN A CONFLICT AREA?
YES NO
3-DIGIT
CODE1+CODE
SEL # CODE
SEL #
MINIMUM COS TO DIAL 976?
01850C67
Description
PROGRAM RECORD FORM
60Automatic Route Selection 

Table 2-7, 6-DIGIT TABLE PROGRAM RECORD FORM
 
AREA 
CODEMATCH
SEL #DEFAULT
SEL #NNX
LIST
01850C76
OPERATOR ASSISTED
CALLS SEL #
INTERNATIONAL
CALLS SEL #
EQUAL ACCESS CALLS
SELECTION #
Description
PROGRAM RECORD FORM
Automatic Route Selection61 

- For Your Notes -
Description
PROGRAM RECORD FORM
62Automatic Route Selection 

PROGRAM ENTRY
Section 3, Program Entry
Table of Contents
Program Entry Introduction...... ..................................................................65
Using the Program Entry Charts .................................................................65
Storing ARS Data........................................................................................66
Abbreviated Programming..........................................................................66
Program Entry Charts...

Description
PROGRAM ENTRY
64Automatic Route Selection 

PROGRAM ENTRY INTRODUCTION
This section describes the procedures for entering data into system mem-
ory for each of the Automatic Route Selection (ARS) programmable fields
(i.e, options). The entries are obtained from the ARS Program Record
Forms (PRFs) located at the end of Section 2, SOFTWARE CONFIGURA-
TION. This section is arranged according to the order of the ARS com-
mands that appear on the programming terminal during program entry.
These commands are outlined in the Command Structure chart at...

Storing ARS Data
While you are programming ARS data, your entries (i.e., modified ARS
data) are temporarily stored in a dedicated section of Random Access
Memory (RAM) called the Workspace. When you use the Store (S) com-
mand, your entries (in the Workspace) are transferred to the system RAM
where they are used as current data by ARS. When you use the Exit (E)
command, any modified data will be stored in RAM.  If you use Exit with-
out Store, your entries are automatically stored in system RAM.
The Quit...

PROGRAM ENTRY CHARTS
Rate Periods
 
01850C81
GA(ARS EDITOR)
DISPLAY CONFIGURE INITIALIZE SHORT VERBOSE EXIT D= M= I= S= V= E=
CNF>DIAL TREATMENTS E.A. & OPR-ASSIST RATE PERIODS CALL ROUTE OPTIONS
6-DIGIT TABLE EXITE= R= C=
S= Q=
3-DIGIT TABLE T=
RP>DISPLAY DATA MODIFY DATA STORE NEW DATA STORE & EXIT D= M= S= E=EXIT Q=

D=
ARS>
>D
DISPLAY
   1- SYSTEM DATA
   2- WORKSPACE DATA
   3- BOTH 1 & 2
D>
Press1, 2 or 3.
SYSTEM DATA
    DAY                  PERIOD           RP#TRANSFER COMPLETE
RP>[TRANSFER...

Dial Treatments
 
01850C79
GA(ARS EDITOR)
DISPLAY CONFIGURE INITIALIZE SHORT VERBOSE EXIT D= M= I= S= V= E=
CNF>DIAL TREATMENTS E.A. & OPR-ASSIST RATE PERIODS CALL ROUTE OPTIONS
6-DIGIT TABLE EXIT E= R= C=
S= Q=
3-DIGIT TABLE T=
DT>DISPLAY DATA MODIFY DATA STORE NEW DATA STORE & EXIT D= M= S= E=EXIT Q=

D=
ARS>
>D
DISPLAY
   1- SYSTEM DATA
   2- WORKSPACE DATA
   3- BOTH 1 & 2
D>
Press1, 2 or 3.
SYSTEM DATA
DT #01: F0613D01PRE
DT #02: F041D03W6ORE
DT #03: NOT DEFINED
DT #04: NOT DEFINED
DT #05: NOT...

Call Route Options
 
01850C82
GA(ARS EDITOR)
DISPLAY CONFIGURE INITIALIZE SHORT VERBOSE EXIT D= M= I= S= V= E=
CNF>DIAL TREATMENTS E.A. & OPR-ASSIST RATE PERIODS CALL ROUTE OPTIONS
6-DIGIT TABLE EXITE= R= C=
S= Q=
3-DIGIT TABLE T=
CRO>DISPLAY DATA MODIFY DATA D= M=
EXIT E=

D=
ARS>
CRO>D
DISPLAY
   1- SYSTEM DATA
   2- WORKSPACE DATA
   3- BOTH 1 & 2
D>
Press1, 2 or 3.
SYSTEM DATA
S#
01
02ARS> CRO>M
  SEL. NO. -
Enter Selection #
from table.

F=FIND I=INSERT A=ADD E=EXIT
   
SEL. NO. -
COS=Class of...