Nitsuko Digital System Feature And Terminal Programming Manual

ARS WITH DIAL TREATMENT AUTHORIZATION CODES
You may be required to enter a Dial Treatment Authorization code before
certain calls can be placed. Check with your attendant or communications
manager to see if you are required to enter these codes, and, if so, what
the valid Dial Treatment Authorization Codes are. If an SMDR Account
Code is also required, the Dial Treatment code is entered after the SMDR
Account Code.
Using Dial Treatment Authorization Codes
To enter a Dial Treatment Authorization Code:...

BYPASSING ARS
Your extension may be allowed to bypass ARS for certain types of calls.
Check with your attendant or communications manager to see if you have
this capability. 
Note: 
 When ARS is bypassed, the call is restricted according to Toll Re-
striction and Class of Service programming.
To bypass ARS:
•Press any loop key not assigned to trunk group 90.
OR
•Use a two-digit dial-up trunk group code (91-98).
OR
•Use Direct Trunk Access (396-427).
OR
•Press any line key.
OR
•Dial the three-digit trunk...

COMMAND STRUCTURE, ARS
ARS COMMAND LEVEL (ARS>)
D= DISPLAY (ALL DATA) Display all ARS data.
M= CONFIGURE Enter or change ARS data.
CONFIGURE COMMAND LEVEL (CNF>)
D= DIAL TREATMENTS
DIAL TREATMENTS COMMAND LEVEL (DT>)
D= DISPLAY DATA Display workspace and/or system RAM data.
M= MODIFY DATA Enter or change Dial Treatment data.
MODIFY DATA COMMAND LEVEL (DT#>)
D= DISPLAY Display entry for Dial Treatment currently being modified.
F= FIND Select another Dial Treatment for modification.
C= CHANGE Change entry...

CALL ROUTE OPTIONS MODIFY DATA COMMAND LEVEL (>)  (cont.)
M= MODIFY DATA Enter or change Call Route Options data.
    SEL. NO. - Designate Selection Number for option to be modified.
    RP NO. Designate Rate Period for option to be modified.
MODIFY DATA COMMAND LEVEL 
F= FIND Select another Selection # and Rate Period for modification.
I= INSERT Create and insert option at specified point in option list.
A= ADD Create and insert option at bottom of option list.
D= DELETE Delete option (s) from option...

3-DIGIT TABLE COMMAND LEVEL (3DIG>)
   (cont.)
E= STORE & EXIT Store entries and exit to the ARS Command Level.
Q= EXIT Exit to the ARS Command Level without saving changes.
Q= EXIT Exit from the M= Configure Command Level.
I= INITIALIZE
INITIALIZE COMMAND LEVEL (INI>)
A= ALL DATA Initialize all data.
D= DIAL TREATMENTS Initialize just the Dial Treatments data.
O= OPR-ASSIST & E.A. SEL. NOS Initialize just the E.A. & OPR. ASSIST data.
R= RATE PERIODS Erase current Rate Periods table and load standard...

CHARTS 

Table 1  SYSTEM FLASH RATES (Page 1 of 3)
Graphite Phone with Dual Color LEDs
Your phone is idle (not on a call)All LEDs out (dark)
Outside Calls
An outside line is busy The line key is On Red
An outside call is ringing your phone The line key flashes Slowly Red if it’s shared, Off then
Quickly Flashing Green if it’s just for you
And then you answer it The line key is On Green 
Or answer it with Privacy released The line key flashes Quickly Green
You place the outside call on Hold The line key is On then...

Table 1  SYSTEM FLASH RATES (Page 2 of 3)
Phone with Single Color (Red) LEDs
Your phone is idle (not on a call)All LEDs out (dark)
Outside Calls
An outside line is busy The line key is On
An outside call is ringing your phone The line key flashes Slowly if it’s shared, Off then flashing
Quickly if it’s just for you
And then you answer it The line key is On
Or answer it with Privacy released The line key flashes Quickly
You place the outside call on Hold The line key is On then flashing Moderately
Or a...

Table 1  SYSTEM FLASH RATES (Page 3 of 3)
       DSS Console
All programmed extensions  idle (not on a
call)All LEDs out (dark)
Outside Calls
An outside line is busyThe line key on ON Red
Intercom Calls
You place an Intercom call DSS key being called flashes Quickly Red
You place the Intercom call on HoldHOLD flashes Moderately Red
Miscellaneous Features
An extension activates Do Not DisturbDSS key for that extension flashes Quickly
Red