Nitsuko Digital System Administrators Guide

C amp- O n (C all Wa iting)
&
Be assured that you are connected to a busy extension as soon as it
becomes free. 
When you make an Intercom call and get busy tone, Camp-On lets you dial a code
and wait off-hook for the busy extension to become available.  Dialing the code may
send Call Waiting beeps to the busy user (if enabled in programming).  The
DIGITAL SYSTEM automatically connects you to that extension when the busy user
hangs up or if the busy user chooses to interrupt their call and respond to...

To answer Call Waiting
beeps from an Intercom
call:
Your hear two beeps and ICM flashes.
1.At a multibutton phone, press ICM to answer the wait-
ing call.
OR
At an ESL set, press HLD and dial * 2. 
-Your first call goes on Hold.
-To alternate between the calls, see Split on page
167.
To answer Call Waiting
tones from an outside call:
You hear two beeps and a Line/Loop key flashes.
1.Press HOLD to hold the call you are on. 
2.At a multibutton phone, press flashing Line/Loop key.
OR
At an ESL set, dial *...

C entrex/P BX F ea ture  Keys
&
Access a PBX/Centrex feature with a single touch. 
When your system is installed behind a PBX or Centrex, a PBX/Centrex key lets you
access a PBX/Centrex feature without dialing the feature code.  The feature code is
stored in a key so you can just press the key.
PBX/Centrex keys can be enabled only through terminal programming, which
requires the AUX Module.  To enable PBX/Centrex keys, see Centrex Compatible
Feature Keys in the DIGITAL SYSTEM Feature and Terminal...

C lass of Se rvic e
&
Each extension can have a customized group of features depending
on its needs. 
A Class of Service (COS) is a group of feature and dialing options that you can
assign to an extension.  First, you customize a COS by enabling or disabling each
option, then you assign the COS to an extension.  You can customize up to 28
different COSs (00-27), and you can assign the same COS to any number of
extensions.  In addition, there is a special COS (30) for attendant extensions.  
Below are the...

·Single Ring for ASI Calls = N 
See Analog Station Interface on page 31.
Using the Feature
N/A
Understanding Related Programming
Program 1To customize Class of Service for an extension or line
(see also Program 18 [I])
Program 18 (I) To assign a Class of Service from Program 1 to an
extension (COS  + # + 01-27 + #)  
Class of Service
Part I:  DIGITAL SYSTEM Features 59 

Conference
&
Conduct a telephone meeting with inside and/or outside parties so
you do not have to leave your office.
Conference lets you set up a three-way telephone conversation.  To set up a
Conference, you establish an Intercom or outside call, then add someone to it.  You
can add an outside party or an extension user.
To set up a Conference with two outside parties, your system must be equipped with
loop start lines that have disconnect supervision.
Initial Configuration 
Conference allowed
Using the...

Data
&
The DIGITAL SYSTEM can also be used for data
communications. 
The Data feature lets you connect a Data Module (P/N 88400), a Dataport PCB (P/N
89460), and/or a Modem Pooling PCB (P/N 89465) to the system for data
communications with computers, terminals, printers and other RS-232 devices.
Note:  Depending on the version of the your system, you may need to install an AUX
Module to use Dataport and Modem Pooling PCBs.  For more information on all
Data devices, see the Data Products Manual (P/N...

De laye d Ringing Assignment
&
Have your calls ring at your secretary’s phone, then at your phone
after a short delay. This way, you are not disturbed by a ringing
call unless your secretary cannot get to it right away. 
Delayed Ringing Assignment (DRA) lets you enable or disable delayed day/night
ringing for: 
·Lines 
·Call Coverage keys 
·Pickup Group keys 
A call rings the line or key after a pre-programmed delay instead of right away.  To
enable/disable DRA, your extension must have program access...

D ia ling N umber  Pr evie w
&
Make a mistake in dialing and not have to redial the entire number. 
If you have a Display Phone, Dialing Number Preview lets you dial an outside
number, review its digits on your display and correct them, if necessary, before the
system dials out the call.  To correct a mistake, you back up to the mistake and enter
the correct digit.  Then you simply press a few keys to have the system dial out your
call.
Initial Configuration 
Dialing Number Preview always allowed at...

Direc t Inwa rd Line s
&
A DIGITAL SYSTEM line can be assigned to a specific extension
so outside callers can directly reach that extension.  For example, a
DIL could ring a Sales Manager’s extension, and if unanswered, all
the other salespeople in the group. 
The Direct Inward Line (DIL) feature lets you program a line so it rings a specific
destination, and if unanswered, rings other extensions.  The initial destination
(termination) for a DIL can be: 
·An extension 
·The master extension for a UCD...