Nitsuko 124i/384i Software Manual

7. Enter the password level (0, 2, 3 or 4) + HOLD
User No?
8. Repeat from step 3 to program another user.
OR
HOLD to exit.
0200 - Programming Passwords
0201 - Setting the Programming Passwords
92000SWG08  Issue 1-0 PROGRAMMING   715 

0202 - Setting User Passwords
  Sorts Data   Updates CEU   Can be Copied
Description
 124i Available — one Tenant Group. 384i Available — four Tenant Groups.
- An extension’s Class of Service
cannot be changed via Service Code.- Allowing an extension to change Class
of Service via Service Code 177
requires system software 3.07.31.
INUse Program 0202 - Setting User Passwords to set the password a user must dial before:
•Setting the system Time and Date, changing the Music on Hold tone and changing an...

0300 - Basic Hardware Setup (Part B)0301 - Inter-Tenant Calling
  Sorts Data   Updates CEU   Can be Copied
Description
 124i Not available. 384i  Available.
INUse Program 0301 - Inter-Tenant Calling to set the parameters for Inter-Tenant Calling. If enabled:
•Intercom calling between tenants is allowed
•An extension port in one Tenant Group cannot have the same extension number as an extension port in
another group
•An extension user can Transfer one of their Tenant Group’s trunks to an extension in...

0302 - Music on Hold and Conference SetUp
 Sorts Data
✔  Updates CEU   Can be Copied
Description
 124i  System allows either 8 four-party
conferences or 4 eight-party
conferences. 384i  Each CTDU PCB allows either 4
four-party conferences or 2 eight-
party conferences.
INUse Program 0302 - Music on Hold and Conference Setup to set the Music on Hold selection and the system
Conference mode. For MOH, the system can provide silence to callers on Hold or one of two synthesized selec-
tions. The 124i system...

0303 - DTMF and Dial Tone Circuit Setup
  Sorts Data   Updates CEU   Can be Copied
Description
 124i Not available. 384i Available.
INUse Program 0303 - DTMF and Dial Tone Circuit Setup to allocate the circuits on the CDTU PCBs for either
DTMF receiving or dial tone detection. Each CDTU PCB has 16 individual circuits, grouped into 4 four-circuit
blocks. You assign a function to each block. Since the system allows a total of eight CDTU PCBs, you can pro-
gram a total of 32 blocks (128 circuits).
Use the...

Feature Cross Reference
TBD
Telephone Programming Instructions
To enter data for Program 0303 (DTMF and Dial Tone Detection Circuit Setup):
1. Enter the programming mode.
2. 0303 + HOLD
Block No?
3. Enter the number of the CDTU block you want to program (1-32).
4. HOLD
Block_nn:
5. Enter the CDTU block type (0-4) + HOLD
Block No?
6. Repeat from step 3 to program another block.
OR
HOLD to exit.
0300 - Basic Hardware Setup (Part B)
0303 - DTMF and Dial Tone Circuit Setup
720   PROGRAMMING 92000SWG08  Issue...

0304 - PGDU PCB Alarm/Fax Sensor Setup
  Sorts Data   Updates CEU   Can be Copied
Description
 124i 4 sensors per PGDU PCB — 8 max
per system (2 PCBs). System has 52
trunk ports. 384i 8 sensors per PGDU PCB — 16 max
per system (2 PCBs). System has
128 trunk ports.
INUse Program 0304 - PGDU PCB Alarm/Fax Sensor Setup to set the function of the sensors on the PGDU
PCBs. Each PCB has sensors which you can set as fax sensors or alarm sensors. The system allows up to two
PGDU PCBs.
The alarm sensors connect...

0305 - PGDU PCB Sensor Activation Mode
  Sorts Data   Updates CEU   Can be Copied
Description
 124i 4 sensors per PGDU PCB — 8 max
per system (2 PCBs). System has 52
trunk ports. 384i 8 sensors per PGDU PCB — 16 max
per system (2 PCBs). System has
128 trunk ports.
INUse Program 0305 - PGDU PCB Sensor Activation Mode to have the PGDU sensors activate for either nor-
mally open or normally closed alarm or fax relay contacts.
Conditions
The sensor circuits on the PGDU PCB require a 10-30 V  DC power...

0306 - Pre-ringing Enable
  Sorts Data   Updates CEU   Can be Copied
Description
 124i Available. 384i Available.
INUse Program 0306 - Pre-ringing Enable to enable or disable pre-ringing for trunk calls. This sets how a trunk
initially rings a telephone. With pre-ringing, a burst of ringing occurs as soon as the trunk’s LED flashes. The
call then continues ringing with the normal ring cadence cycle. Without pre-ringing, the call starts ringing only
when the normal ring cadence cycle occurs. this may...

0307 - Setting the ISDN Line Operating Mode
  Sorts Data   Updates CEU   Can be Copied
Description
 124i Not available. 384i Available.
INRefer to the system PRI (P/N 92000PRI**) or BRI (P/N 92000BRI**) Manual.
0300 - Basic Hardware Setup (Part B)
0307 - Setting the ISDN Line Operating Mode
724   PROGRAMMING 92000SWG08  Issue 1-0