NEC Ucd-Xl Installation Guide

NDA-30078   Revision 1.0Page 9
UCD-XL Installation Guide Introduction
Initialization/Termination - All UCD-XL components must be initialized and 
terminated through the APM Operations Menu. These actions and their 
sequencing among the components are discussed on page 49. Use the 
instructions provided in the APM Operations Manual. Refer to page 49 for more 
information.
Backups - It is recommended that a backup of the “oai” filesystem be made on 
diskettes (device name “/dev/rfd0”) or cartridge tape...

Introduction UCD-XL Installation Guide
Page 10NDA-30078   Revision 1.0
This Page Left Blank. 

NDA-30078   Revision 1.0Page 11
UCD-XL Installation Guide Installation
Chapter 2 Installation
This chapter provides instructions for installing the UCD-XL software. In addition 
to the information in this chapter, you can refer to the Applications Manager 
(APM) Installation Manual for more information on installing software from 
release media.
Installing UCD-XL
Begin the installation of UCD-XL by loading the UCD-XL software from the 
release media. Log in to the APM Platform Management Menu, select the...

Page 12NDA-30078   Revision 1.0
Installation UCD-XL Installation Guide
This usually means that the configuration data for the current component has been 
lost. After pressing the Enter key, you may repeat the installation procedure from 
the beginning (re-loading the UCD-XL software), or you may manually configure 
the components as described on page 31.
UCD-XL MonitorThe primary function of the UCD-XL Monitor is to intercept calls and route them 
to an available port of an appropriate UCD group. The...

NDA-30078   Revision 1.0Page 13
UCD-XL Installation Guide Installation
7. Type in the destination link and press Enter. 
The source and destination links are names that identify sets of OAI 
communication characteristics between the UAP (source) and the PBX 
(destination). These names are defined under the System Configuration Menu 
of APM System Administration. Refer to the APM Operations Manual for 
further information.
8. After entering the selection (or entering the names of the source and...

Page 14NDA-30078   Revision 1.0
Installation UCD-XL Installation Guide
12. The installation software issues the command
CU\USd dXU di`U _V cdQdYcdYSc Vb_] dXU V_\\_gY^W \Ycd*
K!M Q\\ cdQdYcdYSc ]QZ_b Q^T ]Y^_b
KM ]QZ_b cdQdYcdYSc _^\i
K#M ^_^U
KaM aeYd Y^cdQ\\QdY_^
The installation software issues the prompt
5^dUb RbQS[UdUT fQ\eU .
13. Type the number corresponding to the statistics you want, and press Enter.
Major statistics cover call activity per group, and include incoming call count, 
abandoned...

NDA-30078   Revision 1.0Page 15
UCD-XL Installation Guide Installation
16. The installation software issues the following message and prompt:
DXU =_^Yd_b S_]]e^YSQdUc gYdX _^U _V ]_bU =UccU^WUbc Ri ]UQ^c _V
´bUaeUcd RY^cµ Y^ cXQbUT ]U]_bi DXU aeQ^dYdi _V bUaeUcd RY^c ^UUTUT
Yc RQcUT e`_^ SQ\\ dbQVVYS f_\e]Uc CU\USd Vb_] dXU V_\\_gY^W \Ycd*
K!M c`USYVi aeQ^dYdi
KM  RY^c !))) SQ\\cX_eb
K#M #  RY^c #   $))) SQ\\cX_eb
K$M $  RY^c %    SQ\\cX_eb
KaM aeYd Y^cdQ\\QdY_^
5^dUb RbQS[UdUT fQ\eU ....

Page 16NDA-30078   Revision 1.0
Installation UCD-XL Installation Guide
21. Type y or n to indicate whether or not you will use UCD-XL for voice mail ac-
cess, and press Enter.
If you respond with an n, the installation software displays the following 
message:
DXU =UTYQd_b S_]`_^U^d gY\\ ^_d RU S_^VYWebUT
and installation of the UCD-XL Monitor continues with step 25.
If you respond with a y, the installation software displays the following 
message:
E34H< =UTYQd_b Yc ^USUccQbi d_ ]Q^QWU dXU =39 \Y^[...

NDA-30078   Revision 1.0Page 17
UCD-XL Installation Guide Installation
25. The installation software issues the prompt
9c dXYc S_^VYWebQdY_^ _V dXU =_^Yd_b QSSU`dQR\U/ i _b ^
If you are satisfied with this configuration, type y and press Enter. This ends 
the installation of UCD-XL Monitor.
If you made a mistake during this configuration, type n and press Enter; 
installation of the UCD-XL Monitor starts over at step 1 on page 12.
26. The installation software displays the following messages (if...

Page 18NDA-30078   Revision 1.0
Installation UCD-XL Installation Guide
UCD-XL MediatorThe UCD-XL Mediator receives and transmits MCI messages between the PBX 
and the VMS. If you are not using a Voice Mail System, you do not need to 
configure the UCD-XL Mediator.
If you have just finished configuring the UCD-XL Monitor, go to step 3 below to 
configure the UCD-XL Mediator; otherwise, begin configuration of the UCD-XL 
Mediator with step 1.
1. The installation software displays the following message
DXU...