NEC Neax2000 Ivs Command Manual

CHAPTER 3 ND-45669 (E)
Pag e 7 2
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
4. DATA TABLE:
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
012 Busy Verification 0
1
 
Not available
Available
014 Attendant Loop Release 0
1
 
Provided
Not provided
018 When the system is in night mode, an attendant (dial “0”) call 
from a station is automatically transferred to a specific sta-
tion.0
1
 
Not transferred
To transfer
(See CM51 YY = 13)
021 Station to Station call during a C.O. outgoing...

ND-45669 (E) CHAPTER 3
Page 73
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
044 Toll Restriction for outgoing call by System Speed Dialing 
feature.0
1 Not provided
Provide
045 Warning tone sent to connected parties during Executive 
Override or Attendant Override.0
1 Only once
Every 4 sec.
048 Passing Dial Tone facility 0
1 Not available
Available
050 If * button on DTMF telephone is pressed while hearing busy 
tone, it is regarded as a Switch Hook Flash.0
1 Effective
Ineffective
051...

CHAPTER 3 ND-45669 (E)
Page 74 Addendum-001
Revision 2.1 AUGUST, 1998
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
078 This setting determines the trunk seizing sequence when CM 
35 YY = 83 is set to 0.
Note:When NEAX 2000/1000IVS is installed with loop-
start trunks, it is important to select the highest
available trunk setting to prevent call collisions. 0
1 Highest available trunk
Lowest available trunk
085 Types of PS No-Answer timer 0
1 No...

ND-45669 (E) CHAPTER 3
Addendum-001 Page 74-1
AUGUST, 1998 Revision 2.1
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
110 1000-Slot Memory Block Number “3” for Station Speed Di-
aling is used as the Memory Block for System Speed Dialing.0
1 Available (See CM20, A50)
Not available
111 1000-Slot Memory Block Number “1” for Station Speed Di-
aling is used as the Memory Block for System Speed Dialing.0
1 Available (See CM20, A51)
Not available
112...

THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 74-2 Addendum-001
Revision 2.1 AUGUST, 1998
This page is for your notes. 

ND-45669 (E) CHAPTER 3
Pag e 75
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
113 Outgoing C.O. Line Call from a Station to Station connection. 0
1 Not allowed
To allow
114 Answer preference for enhanced Trunk Direct Appearance 0
1 Display 2-digit trunk ID code (CM30 
YY = 19, last two digits assigned)
Display 4-digit trunk ID code (CM30 
YY = 19)
115 A station user is allowed to break into a call between a C.O. 
line party and another station by Executive Override.0
1 Not allowed
To...

CHAPTER 3 ND-45669 (E)
Pag e 7 6
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
133 A trunk line placed in Consultation Hold by Call Park-Sys-
tem/Tenant, can be retrieved by pressing a trunk line appear-
ance key on any Multiline Terminal.0
1
 
Not available
Available
135 Periodic Time Indication Tone Sending for C.O. Line connec-
tion. (CM41 Y = 0, Function No. 09)0
1
 
To send 
Not sent 
136 Periodic Time Indication Tone Sending for a Tie Line con-
nection (When the data for 135 of...

ND-45669 (E) CHAPTER 3
Addendum-002 Page 77
JANUARY, 1999 Revision 2.2
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
149 In delay-type paging, when the paged party encounters a busy 
paging circuit, Call Back is automatically set. (Applicable to 
both Radio Paging and Speaker Paging.)0
1
 
To set
Not set
150 Restriction of a station to station call between tenants by 
CM63 Y=1 is temporarily cancelled by external key.0
1
 
To cancel
Not cancelled
151...

ND-45669 (E) CHAPTER 3
Addendum-002 Page 70-1
JANUARY, 1999 Revision 2.2
CM07
COMMAND CODE
TITLE:
DTI TRUNK/ISDN TRUNK ASSIGNMENT
07
YY1S T DATA 2ND DATA
RELATED
COMMAND
DATA MEANING DATA MEANING
05 32XX Virtual Channel No.
32 XX
Home-Side Trunk 
Virtual Channel
No. 00 – 30 (Even No.)
Mate-Side Trunk
Virtual Channel
No. 01 – 31 (Odd No.)
DXXX Trunk Number
(D000 – D255)
Note:Trunk numbers
already assigned by
CM10 cannot be
used. 

THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 70-2 Addendum-002
Revision 2.2 JANUARY, 1999
This page is for your notes.