NEC Neax2000 Ivs Command Manual

CHAPTER 3 ND-45669 (E)
Pag e 6 4
Revision 2.0
CM02
COMMAND CODE
TITLE:
SETTING OF SYSTEM CLOCK
02
MAT
4. DATA TABLE:
1. FUNCTION:
This command is used to assign clock data (day, date and time).
2. PRECAUTION:
(1) The system clock starts when EXE is depressed.
(2) Reenter all the Clock Data if “HARD ERROR” is displayed as a result of this command.
(3) This command is included in MAT mode menu “E1” (Setting of System Clock [COM02]).
3. ASSIGNMENT PROCEDURE:
SECTION NO. DATA MEANING REMARKS
0
[Date...

ND-45669 (E) CHAPTER 3
Pag e 65
Revision 2.0
CM03
COMMAND CODE
TITLE:
LOG IN/LOG OUT OF PASSWORD MODE
03
Note 1:The password for each level is set by CME9. The allowed commands for each Password Level
are defined with CME7.
Note 2:“OK” is displayed when the login is successful.
Note 3:For security purposes, when entering a password, “*” is displayed.
Note 4:The password mode is automatically logged out unless a command is entered within 10 minutes
after logging in.
1. FUNCTION:
This command is used to...

CHAPTER 3 ND-45669 (E)
Page 66 Addendum-001
Revision 2.1 AUGUST, 1998
CM04
COMMAND CODE
TITLE:
LANGUAGE INDICATED ON MULTILINE TERMINAL LCD
04
INITIAL
4 . D ATA  TA B L E :
1. FUNCTION:
This command selects the language that displays on the Multiline Terminal LCDs.
2. PRECAUTION:
This command requires a system reset after setting the data.
3. ASSIGNMENT PROCEDURE:
: Initial Data
Y1 S T  D ATA 2 N D  D ATA
DATA MEANING DATA MEANING
00 00 Selected language for Multiline Terminal 
LCD0
1
2
7Japanese...

ND-45669 (E) CHAPTER 3
Addendum-001 Page 67
AUGUST, 1998 Revision 2.1
CM05
COMMAND CODE
TITLE:
CARD ASSIGNMENT
05
MAT
4. DATA TABLE:
1. FUNCTION:
This command is used to inform the main processor card (CP00 or CP03) of the SENSE switch (sense
wheel) setting on each AP circuit card that is installed.
2. PRECAUTION:
(1) This command requires a system reset after setting the data.
(2) This command is included in MAT mode menu “E2” (Board Assignment [COM02]).
3. ASSIGNMENT PROCEDURE:
: Initial Data
SENSE...

CHAPTER 3 ND-45669 (E)
Page 68 Addendum-001
Revision 2.1 AUGUST, 1998
CM05
COMMAND CODE
TITLE:
CARD ASSIGNMENT
05
MAT
Note:Set the SENSE switch on the AP circuit card to match an unequipped slot number as shown below.
SENSE WHEEL (04 - 15)04 05 06 07 08 09 10 11 12 13 14 15
SWITCH SETTING VALUE456789ABCDEF 

ND-45669 (E) CHAPTER 3
Pag e 69
Revision 2.0
CM06
COMMAND CODE
TITLE:
MISC. TRUNK NUMBER ASSIGNMENT
06
4. DATA TABLE:
1. FUNCTION:
This command assigns Miscellaneous Trunk Numbers to each card.
2. PRECAUTION:
This command requires a system reset after setting the data.
3. ASSIGNMENT PROCEDURE:
YY MISC. TRUNK NO. AP NUMBER + CIRCUIT NUMBERRELATED
COMMAND
04 00 ~ 15 MF Receiver /911 Sender
Trunk 00 – 15XXX XX
X
Circuit Number 
(0 – 3)
Slot Number 
(04 – 15) assigned by 
CM05
CM05
07 0 ~ 3 CCH (Common...

CHAPTER 3 ND-45669 (E)
Page 70 Addendum-002
Revision 2.2 JANUARY, 1999
CM07
COMMAND CODE
TITLE:
DTI TRUNK/ISDN TRUNK ASSIGNMENT
07
4 . D ATA  TA B L E :
1. FUNCTION:
This command assigns the DTI/ISDN trunks.
2. PRECAUTION:
This command requires a system reset after setting the data.
3. ASSIGNMENT PROCEDURE:
YY1S T DATA 2ND DATA
RELATED
COMMAND
DATA MEANING DATA MEANING
01 XXXX Channel No. of 24-DTI/30-DTI
XX
XX
Channel No.
for 24-DTI: 00-23
for 30-DTI: 01-15, 16-31
Slot Number assigned by 
CM05
DXXX...

ND-45669 (E) CHAPTER 3
Addendum-002 Page 70-1
JANUARY, 1999 Revision 2.2
CM07
COMMAND CODE
TITLE:
DTI TRUNK/ISDN TRUNK ASSIGNMENT
07
YY1S T DATA 2ND DATA
RELATED
COMMAND
DATA MEANING DATA MEANING
05 32XX Virtual Channel No.
32 XX
Home-Side Trunk 
Virtual Channel
No. 00 – 30 (Even No.)
Mate-Side Trunk
Virtual Channel
No. 01 – 31 (Odd No.)
DXXX Trunk Number
(D000 – D255)
Note:Trunk numbers
already assigned by
CM10 cannot be
used. 

THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 70-2 Addendum-002
Revision 2.2 JANUARY, 1999
This page is for your notes. 

ND-45669 (E) CHAPTER 3
Pag e 71
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
1. FUNCTION:
This command is used to assign basic features on a system-wide basis.
2. PRECAUTION:
After setting 1st data 390 and 391, system reset is required.
3. ASSIGNMENT PROCEDURE:
   +   08  +  +    +  +    + STDEBASIC SERVICE 
FEATURE 
(3 digits)DEDATA (0/1)
(1 digit)EXE
[CM08] Basic Service Features