NEC Neax 2400 Ipx Installation Manual

NDA-24306   CHAPTE R 4
P ag e 283
Re visi on 1 .0
S YS TEM  S TA RTU P
Note:  
Pro ced ures (a)  t h rough  ( e )  mu st b e p erf ormed  in all  LNs and  I S W , i nd iv idua ll y .
N AP-2 00-0 19
S hee t 5 /6
Pro gram  In sta ll  a nd Lo ad
(d )  P ro ced ure  fo r  A pp li c a ti o n  Softw are  I n sta ll   Sta tu s c h an g e o f 7  S eg m en t  L ED  o n t h e C PU  F ro nt 
P an el. 
W ARNING:  Rem oval  or  Ma ke  Busy  of  th e HFD c ard  is
not allowed while the Floppy Disk or Hard
Disk is...

CHAPTER 4 NDA-24306
Page 284
Revision 1.0
SYSTEM STARTUP
(e)  Procedure for Program Load
This section describes system start-up procedure in which a program is loaded from the HD to the MEM and the
data memory is cleared.
Note:Procedures (a) through (e) must be performed in all LNs and ISW, individually.
NAP-200-019
Sheet 6/6
Program Install and Load
START
Program Load Set the SENSE switch to “1” (restart with data 
memory clear) on the CPU Front Panel and press the 
CPURST button.
The system is...

NDA-24306 CHAPTER 4
Page 285
Revision 1.0
SYSTEM STARTUP
This NAP explains the procedure to assign office data to each node and ISW, after the Program Install and Load in
NAP-200-019 are thoroughly completed. Follow the procedures below:
Note 1:See Sheet 3/6 in this NAP.
Note 2:See Sheet 4/6, 5/6 in this NAP.
Note 3:The procedures here are required in each LN, independently.
NAP-200-020
Sheet 1/6
Assignment of Office Data
START
Start up the MAT
Enter basic data in ISW Assign the following  basic data via...

CHAPTER 4 NDA-24306
Page 286
Revision 1.0
SYSTEM STARTUP
Note 2:
See Sheet 4/6, 5/6 in this NAP.
Note 3:The procedures here are required in each LN, independently.
NAP-200-020
Sheet 2/6
Assignment of Office Data
Assignment of Office Data
Note 3
Assign the remaining office data according to the office data 
programming sheet. 
Note 2
(Assign all the remaining NDM data, too, if the node is 
designated as the Network Control Node. For details, refer to 
the Fusion Network System Manual.)
Confirmation of...

NDA-24306 CHAPTER 4
Page 287
Revision 1.0
SYSTEM STARTUP
Note 1:
To initially start up the system, the data below must be at least assigned in the following nodes:
1.
ASYD SYS1
INDEX 62, bit 6-7 (ACT/ST BY Changeover at Routine Diagnosis)
INDEX 86, bit 2-3 (Fault Recovery on TRK Ineffective Hold Detection)
INDEX 87 (Routine Diagnosis Program Start Time (Hour))
INDEX 88 (Routine Diagnosis Program Start Time (Minute))
INDEX 89 (Items of Routine Diagnosis)
INDEX 90 (Items of Routine Diagnosis)
ASYDL SYS1...

CHAPTER 4 NDA-24306
Page 288
Revision 1.0
SYSTEM STARTUP
3.
ASYD SYS1
INDEX 3 (Configuration of Time Division Switch)
INDEX 30 (Mounting capacity of Data Memory)
INDEX 31 (Mounting capacity of Common Memory)
INDEX 58, b0 (Configuration of CPU) 0/1=Single/Dual
INDEX 64, b0=0 (µ-law for Time Division Switch)
INDEX 86, b0-1, 4, 6-7 (Details on System Message Output)
INDEX 91, b6-7 (PLO mounting condition)
INDEX 96-115 (Office Name for each LN/ISW) Note
Note:
Office Name can be entered also via AOFC...

NDA-24306 CHAPTER 4
Page 289
Revision 1.0
SYSTEM STARTUP
Note 2:
When assigning office data, be sure to enter the following Fusion Trunk Data, too, by using ACRD and
AFPC command. Refer to “Office Data Specification Manual” for Data Sheet.
1. ACRD: Assignment of Route Class Data
 In LNs, assign the connection route class data for the direction to ISW
 In ISW, assign the connection route class data for the direction to each LN
Note:Assign “12” for this system.
2. AFPC: Assignment of FCCH Routing Data...

CHAPTER 4 NDA-24306
Page 290
Revision 1.0
SYSTEM STARTUP
Figure 020-1  Example of Connection Route Data Assignment (AFPC Command)
NAP-200-020
Sheet 6/6
Assignment of Office Data
LN1
(FPC=11)
ISW
(FPC=20)
LN2
(FPC=12)
LN0
(FPC=10)
 LN0  ISW
 
FPC:  20
FCH:  0
C_RT:  xxx
FCHN/FPC:  20
 LN0  LN1
 
FPC:  11
FCH:  0
C_RT:  xxx
FCHN/FPC:  20
 LN0  LN2
 
FPC:  12
FCH:  0
C_RT:  xxx
FCHN/FPC:  20
 LN1  ISW
 
FPC:  20
FCH:  0
C_RT:  yyy
FCHN/FPC:  20
 LN1  LN0
 
FPC:  10
FCH:  0
C_RT:  yyy
FCHN/FPC:  20
 LN1...

NDA-24306 CHAPTER 4
Page 291
Revision 1.0
SYSTEM STARTUP
NAP-200-021
Sheet 1/5
Check of Lamp Indications and System 
Messages
START
Check lamp indications on Line/ 
Trunk circuit cardsCheck lamp indications on each of the assigned Line/
Trunk circuit cards.
OPE lamp (G): ON
BL lamp (R): OFF
If the lamp indications are other than above, investigate 
per Chapter 6, “FAULT RECOVERY DURING TESTS”
Check lamp indications on control 
system circuit cardsThe OPE lamps (G) are shown in Figure 021-1 through...

CHAPTER 4 NDA-24306
Page 292
Revision 1.0
SYSTEM STARTUP
Figure 021-1  LED Indications of ISW in Normal Operation (example)
NAP-200-021
Sheet 2/5
Check of Lamp Indications and System 
Messages
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19
HSW00 (PU-SW01) TSW01 (PU-SW00) TSW02 (PU-SW00) TSW03 (PU-SW00)
TSW00 (PU-SW00) TSW10 (PU-SW00) TSW11 (PU-SW00) TSW12 (PU-SW00) TSW13 (PU-SW00)
HSW01 (PU-SW01) HSW11 (PU-SW01)
HSW10 (PU-SW01)
(PH-CK16-A/17-A) (PH-CK16-A/17-A)
IOGT0 (PH-GT10) IOGT1 (PH-GT10)...