NEC Neax 2400 Ipx Installation Manual

NDA-24306 CHAPTER 3
Page 253
Revision 1.0
2. [HEADSET TYPE]
This item specifies the type of Headset connected to the H/S1 connector.
a) Press the desired number. An asterisk shows the selected number.
1: The type of Headset is “SUPRA”
2: The type of Headset is “COROLLE”
SRC: Return to Configuration Menu
Note:Default setting is “1: SUPRA”.
b) Press the SRC key. The display returns to Configuration Menu.
c) When configuration data assignment is finished, proceed to [Updating Configuration Data] on Page...

CHAPTER 3 NDA-24306
Page 254
Revision 1.0
3. [MUTE]
This item specifies On/Off setting of the mute function for the HAND H/S0 or H/S1 connector.
While the mute function is set to On, if the Mute key is pressed, the voice at the DESK CONSOLE side is not
sent to the other party.
a) Press the desired number. An asterisk shows the selected number.
1: Both H/S0 and H/S1 are set to On
2: Only H/S0 is set to On
3: Only H/S1 is set to Off
SRC: Return to Configuration Menu
Note:Default setting is “1: H/S0 ON,...

NDA-24306 CHAPTER 3
Page 255
Revision 1.0
4. [REC CONTROL]
This item specifies the operation mode of a recording device. The following two types of modes are available:
[Manual mode]
Manual mode is available when the REC circuit card is mounted in the system. When the REC key is pressed,
the system starts recording and the REC lamp lights. When the REC key is pressed again, the recording stops
and the REC lamp goes off.
[Automatic mode]
In Automatic mode, a dedicated recording device is directly...

CHAPTER 3 NDA-24306
Page 256
Revision 1.0
5. [SUP CONNECTION]
This item specifies whether the supervisory console is connected or not.
a) Press the desired number. An asterisk shows the selected number.
1: Supervisory Console is connected
2: Supervisory Console is not connected
SRC: Return to Configuration Menu
Note:Default setting is “1: NONE”.
b) Press the SRC key. The display returns to Configuration Menu.
Note:Do Not change this data.
c) When configuration data assignment is finished, proceed to...

NDA-24306 CHAPTER 3
Page 257
Revision 1.0
6. [REC VOLUME ADJUSTMENT]
This item specifies the recording level of the received voice from the other party. Note that the voice level at the
operator side cannot be adjusted.
a) Press the desired number. An asterisk shows the selected number.
1: +2dB Up
2: 0dB (Standard level)
3: -4dB Down
4: -8dB Down
SRC: Return to Configuration Menu
Note:Default setting is “2: 0dB”.
b) Press the SRC key. The display returns to Configuration Menu.
c) When configuration data...

CHAPTER 3 NDA-24306
Page 258
Revision 1.0
7. [BLF]
This item specifies On/Off setting of the BLF function. When using BLF function, system data assignment is
also required.
a) Press the desired number. An asterisk shows the selected number.
1: BLF Available
2: BLF Not available
SRC: Return to Configuration Menu
Note:Default setting is “2: DISABLE”.
b) Press the SRC key. The display returns to Configuration Menu.
c) When configuration data assignment is finished, proceed to [Updating Configuration Data]...

NDA-24306 CHAPTER 3
Page 259
Revision 1.0
8. [HOLD/START/RELEASE/SWAP]
This item specifies the locations of HOLD, START and RELEASE key.
a) Press the desired number. An asterisk shows the selected number.
1: Original setting
2: Swapped setting
Note:The locations of each key changes as shown below.
SRC:Return to Configuration Menu
Note:Default setting is “1: ORIGINAL”.
b) Press the SRC key. The display returns to Configuration Menu.
c) When configuration data assignment is finished, proceed to [Updating...

CHAPTER 3 NDA-24306
Page 260
Revision 1.0
[Updating Configuration Data]
When configuration data assignment is complete, update configuration data according to the procedure below.
When the RELEASE key is pressed, update is cancelled.
While one of the Configuration Menu is displayed on the LCD, press the ANSWER key.
Configuration data is updated and the DESK CONSOLE is automatically restarted.
NAP-200-015
Sheet 41/41
Installation of the DESK CONSOLE and 
Cable Connection
Alarm Position Available
LDNTIE...

NDA-24306 CHAPTER 3
Page 261
Revision 1.0
This NAP explains the installation of the MAT (Maintenance Administration Terminal) and the System Message
Printer focusing on their cable connections.
1. INSTALLATION OF MAT AND CABLE CONNECTIONS
NAP-200-016
Sheet 1/9
Installation of the Maintenance 
Administration Terminal (MAT) and 
Cable Connections
START
Preparation of the MAT Set up the Personal Computer, CRT Display, Printer, and 
so on.
Cable Connection Connect the cables between the MAT and the PBX...

CHAPTER 3 NDA-24306
Page 262
Revision 1.0
Figure 016-1  Cabling of MAT when Using Ethernet
NAP-200-016
Sheet 2/9
Installation of the Maintenance 
Administration Terminal (MAT) and Cable 
Connections
00 01 02 03 04 05 06 07 08 09 10 11
00 01 02 03 04 05 06 07 08 09 10 1112 13 14 15 16 17 18 19 20 21 22 23
LANI (PZ-PC19)
MAT
HUB BASEULPM
10BASET (straight)
PH-PC40(EMA)
PH-IO24(IOC)
Note