NEC Neax 2400 Ipx Hotel Features And Specifications

NEAX2400 IPX Hotel Features and Specifications
NDA-24310, Issue 1Page 89
Hotel Feature Transparency Over CCIS H-22
LEGEND:
X: Available —: Not Available
*: Available with some limitations✰: USA and Canada only G-9 Guest Information Display - PMS Terminal —
G-11 Guest Room Calling - Hotel Attendant —
H-8 House Phone/Hot Line —
✰I-23 Inter-Position Transfer 2 —
L-27 Language Service —
M-6 Message Waiting X
M-22 Maid Status X* Available from Console only
M-51 Manual Switching of C.O. Incoming Call...

NEAX2400 IPX Hotel Features and SpecificationsPage 90NDA-24310, Issue 1
I-23 Inter-Position Transfer 2
I-23Inter-Position Transfer 2
General Description
This feature is applicable for a multi-attendant environment and will provide for the transfer of an incoming station
or trunk call to a group of attendants by use of the Priority Call key.
An attendant can answer an incoming call, put the call on hold at the Attendant loop, and page the requested party.
The paged party calls the attendant, and if a...

NEAX2400 IPX Hotel Features and Specifications
NDA-24310, Issue 1Page 91
Language Service L-27
L-27Language Service
General Description
This service provides the announcement in the Guests language and the language information display in case
following services are activated.
1. Announcement Services - The announcements sent to the Guest will be in his/her language.
AUTOMATIC WAKE-UP [A-10]
AUTOMATIC WAKE-UP - HOTEL ATTENDANT [A-58]
GROUP SERVICE THROUGH PMS [G-4]
2. Language Information Display - When...

NEAX2400 IPX Hotel Features and SpecificationsPage 92NDA-24310, Issue 1
M-6 Message Waiting
M-6Message Waiting
General Description
This feature allows the Console, PMS terminal, or Front Desk Terminal to illuminate a lamp on an individual station
to indicate when a message is waiting. With the AUTOMATIC MESSAGE WAITING LAMP OFF [A-48] feature,
the MW lamp is automatically extinguished when the Guest calls to retrieve messages from the message center.
Refer to the AUTOMATIC MESSAGE WAITING LAMP OFF [A-48]...

NEAX2400 IPX Hotel Features and Specifications
NDA-24310, Issue 1Page 93
Message Waiting M-6
Service Conditions (cont’d)
3. Message Waiting set from Message Center Interface cannot be displayed at the Front Desk Terminal or
Console. Message Waiting set from Message Center Interface must be cancelled from message Center
Interface.
4. For the conditions of the LCD display when several services are set to a Guest room D
termat the same
time, see Service Conditions of AUTOMATIC WAKE-UP - Dterm[A-10D]. 

NEAX2400 IPX Hotel Features and SpecificationsPage 94NDA-24310, Issue 1
M-22 Maid Status
M-22Maid Status
General Description
This feature allows the Console, Special Administration, or Guest room stations to update the status of Guest room
conditions. This information is stored in the NEAX2400 IPX Hotel Processor (HP) for printout services, and is
forwarded to the PMS computer for readout. AUDIT REPORTS [A-26] of MAID STATUS are also available. Refer
to the AUDIT REPORTS [A-26] feature description for...

NEAX2400 IPX Hotel Features and Specifications
NDA-24310, Issue 1Page 95
Maid Status M-22
Operating Procedure (cont’d)
Note 3:If the Maid ID code is not in service, the following will be displayed on the LCD (if Dtermis used for a Guest
station) after the Maid Status access code is dialed:
Note 4:This display appears when the “To Be Cleaned,” “Cleaned,” “Ready to Sell,” or “Out of Service” status
is assigned.
To set from the Console
1. Press theSTSkey. The associated lamp illuminates.
2. Dial the Guest...

NEAX2400 IPX Hotel Features and SpecificationsPage 96NDA-24310, Issue 1
M-22 Maid Status
Service Conditions (cont’d)
7. When the room is in “Check-In” status, only the “To Be Cleaned” or “Cleaned” status can be assigned.
When the room is in “Check-out” status, any MAID STATUS can be assigned.
8. After the maid or repairman dials Maid Status access code from Guest room station, either service set tone
or confirmation announcement can be provided, according to selection by the NEAX2400 IPX. (The...

NEAX2400 IPX Hotel Features and Specifications
NDA-24310, Issue 1Page 97
Manual Switching Of C.O. Incoming Call Destination M-51
M-51Manual Switching Of C.O. Incoming Call
Destination
General Description
This feature allows the Console operator to manually change the termination point of a specific group of trunks.
Trunks that normally are used as DIT trunks may be changed to terminate at the Console.
Operating Procedure
To change the termination of DIT trunks from stations to the Console
1. Press...

NEAX2400 IPX Hotel Features and SpecificationsPage 98NDA-24310, Issue 1
M-68 Maid Status - Answerback
M-68Maid Status - Answerback
General Description
This feature allows a maid or other hotel personnel to receive answerback acknowledgment from the PMS (Property
Management System) computer when MAID STATUS has been changed using Guest room station or Special
Administration Station telephones.
Operating Procedure
Service setting from a Guest room station by a maid or repairman
1. Lift handset. Hear dial...