NEC Neax 2400 Imx Wireless System Manual

CHAPTER 5 ND-70290 (E)
Pag e 2 44
Revision 3.0
ASPA
ASPA  : Assignment of Special Access Code
1. GENERAL
This command is used to determined the kind of service and its Access Code to be executed.
List Up Command: LSPA
2. PRECAUTIONS
This part describes only the content of the command added in the PCS system. For more details, refer to the
“Office Data Specification”. 

ND-70290 (E) CHAPTER 5
Page 245
Revision 3.0
ASPA
3. DATA ENTRY INSTRUCTIONS
Access code (Max. 6 digits)
TENANT
NUMBER
( TN )ACCESS CODE
( ACC )
MAX. 6 DIGITSCONNECTION STATUS
ACC
CI
N = Normal service
H = Hooking service
B = Busy service
INDEX
( CI )KIND OF
SERVICE ( SRV )
SRV
STN = Station
SSCA = Service code appendix
OGCA = Outgoing call with route advance
LCR = Least cost routingSSC = Service code 
OGC= Outgoing call 
UNIF = Office termination
ANNC = Announcement service-single announcement 
ANNCM =...

CHAPTER 5 ND-70290 (E)
Pag e 2 46
Revision 3.0
ASPA
When SRV = SSCA (Service code appendix) is assigned; 
NND appears when SIDA=97 (Call Hold Conference).
The number of digits for an access code should be assigned in NND. NND
SERVICE INDEX  A ( SIDA ) 1 - 255 NECESSARY DIGIT ( NND ) 1 - 6
1-100Note
101
102C.F-PS Incoming Incomplete: Set
C.F-PS Incoming Incomplete: Cancel
103~107
Note
SIDA
SIDA Service Name
108
109
110~113
114
115
116~255Number Sharing : Set
Number Sharing : Cancel
Call Forwarding-Dropped...

ND-70290 (E) CHAPTER 5
Page 247
Revision 3.0
ASPA
4. DATA SHEET
 SRV=SSCA Service code Appendix
Note:Refer to the “Office Data Specification” regarding this data.
TENANT
NUMBER
(TN)ACCESS CODE
(ACC)
MAXIMUM
6 DIGITSCONNECTION
STATUS 
INDEX
(CI) N/H/BKIND OF
SERVICE
(SRV)SERVICE
FEATURE
INDEX
(SIDA)
1 - 255NUMBER
OF NEC-
ESSARY
DIGITS 
(NND)SERVICE CONTENTS
1
100
Note 
NNormal
SSCA 101Call Forwarding Incoming 
Incomplete Set H Hooking
BBusy
NNormal
SSCA 102
Incoming Incomplete Cancel
H Hooking
BBusy
103...

CHAPTER 5 ND-70290 (E)
Pag e 2 48
Revision 3.0
ASYD
ASYD  : Assignment of System Data
1. GENERAL
The ASYD/ASYDL command is used to assign the system data of the following node;
Local Node (LN) / Network Control Node (NCN) of the Fusion network.
Stand alone PBX.
List Up Command: LSYD
2. PRECAUTIONS
This part describes only the contents of the command added in Built-in PCS system. For more details, refer to
the “Office Data Specification.” 

ND-70290 (E) CHAPTER 5
Page 249
Revision 3.0
ASYD
3. DATA ENTRY INSTRUCTIONS
Define each bit corresponding
data with referring to the
SYSTEM DATA CONTENTS
SYSTEM
DATA
TYPE
( SYS )DATA
( DATA )
00-FF
( Hex ) SYSTEM
DATA
INDEX
( INDEX )
0 - 511
BIT CORRE-
SPONDING
DATA
DATA
0 / 1BITSYSTEM DATA CONTENTS
DATA
DATA BIT
BIT
DATA
Hex 1
1b0
b1
b2
b3
b4
b5
b6
b7 1
0
0
0
0
0
0n
n+1 FF031
1
0
0
0
0
0
0b0
b1
b2 Not used
Not used
Not used
Not used
Not used
Not used
Number of zzz b3
b4
b5
b6
b7xxx service 0/1=Not to...

CHAPTER 5 ND-70290 (E)
Pag e 2 50
Revision 3.0
ASYD
SYSTEM
DATA
TYPE 
(SYS)SYSTEM 
DATA  
INDEX 
(INDEX)
0 - 511DATA 
(DATA) 
00-FF 
(Hex)BIT CORRE-
SPONDING 
DATA
SYSTEM DATA CONTENTS
DATA 
0/1BIT
15b
0
Access Code for C.F.-Busy Line and C.F. – Don’t Answer Services
0/1 = Same/Separate
Note 1:If a PCS system, C.F.-PS Incoming Call Incomplete also
refers to this system data.
Note 2:If “0” is assigned, assign either SID: 10 or 12 in
command “ASPA”.
b
1Maximum number of Multiple Call Forwarding – All...

ND-70290 (E) CHAPTER 5
Page 251
Revision 3.0
ASYD
4. SYSTEM DATA PROGRAMMING SHEET (1)
S
Y
S
1
SYSTEM
DATA
INDEX
0-511DATA
00-FFB
I
TSYSTEM DATA CONTENTS
30 060 Mounting Capacity of Data Memory (DM) : 1~63 Mbyte (01~3F) 
Normally assigned as “6” 
1
2
3
4
5
6
7
4200Access code using Pre-set dialing
 (e.g.: Special Access Code + Station number)
0/1 : Out/In service
1By cancelling C.F.-PS INCOMING INCOMPLETE
0 = C.F.-DROPPED CALL is also cancelled
1 = C.F.-DROPPED CALL is not cancelled
2Not used
3
4
5
6
7...

CHAPTER 5 ND-70290 (E)
Pag e 2 52
Revision 3.0
ASYD
S
Y
S
1
SYSTEM
DATA
INDEX
0-511DATA
00-FFB
I
TSYSTEM DATA CONTENTS
4210 Miscellaneous Time Counter (MTC) is 
to be assigned a value from 1 Hex to F 
Hex.1) Announcement PS-Out of 
Zone disconnection timer 
(Release Guard timer)
Timer value setting is as 
follows: (TC) sec. × (MTC)
When the data is assigned as 
00, the default data is 30 sec. 1
2
3
4 Timer class (TC)
0 : –  3 : 2 sec.  6 : –
1 : – 4 : – 7 : –
2 : –  5 : – 5
6
7 Not used
4220Miscellaneous...

ND-70290 (E) CHAPTER 5
Page 253
Revision 3.0
AAED
AAED  : Assignment of Announcement Equipment Data
1. GENERAL
This command is used to assign the trunk information related to Announcement Equipment on a tenant basis. 
List Up Command: LAED
2. PRECAUTIONS
This part describes only the contents of the command added in PCS system. For more details, refer to the “Office
Data Specification”.