NEC Neax 2400 Imx Oai System Manual

ND-70895 (E) CHAPTER 5
 Page 61
Revision 1.0
OFFICE DATA DESIGN
Procedure for Setting Basic Office Data for OAI System
2.2 Data for OAI Terminal
In the case of Dterm
1. ASDT (In the case of Business; Station Data), AASP (In the case of Hotel system; Station Data)  Note 1
Assign station data
Voice Port: TEC12 Data Port: TEC13
(Normal setting for others)
Note 1:For ASDT/AASP command, refer to the Command Manual of the NEAX2400 IMX.
2. AKYD (D
term Key Data)
Assign the function key data of Dterm
Assign...

CHAPTER 5 ND-70895 (E)
Page 62
Revision 1.0
OFFICE DATA DESIGN
Procedure for Setting Office Data for OAI Services
3. Procedure for Setting Office Data for OAI Services
This section explains the outline, using conditions, and office data setting procedure of the main OAI service
functions.
3.1 Switch Control Facility (SCF)
3.1.1 Functional Outline
The SCF is the facility that executes, from the Application Program (AP), such control operations as
connections/disconnections between NEAX2400 IMX-accommodate...

ND-70895 (E) CHAPTER 5
 Page 63
Revision 1.0
OFFICE DATA DESIGN
Procedure for Setting Office Data for OAI Services
3.1.2 Using Conditions
1. Normal and abnormal operating sequences pertaining to the basic connection of the SCF are as
described below.
[Normal Sequence]
(a) Upon receiving SCF start request from the AP, the NEAX2400 IMX judges the status (idle,
busy, makebusy, etc.) of the designated calling terminal and destination terminal.
(b) If the calling terminal and the destination terminal are...

CHAPTER 5 ND-70895 (E)
Page 64
Revision 1.0
OFFICE DATA DESIGN
Procedure for Setting Office Data for OAI Services
[Abnormal Sequence]
(a) Upon receiving SCF start request from the AP, the NEAX2400 IMX judges the status (idle, busy, 
makebusy, etc.) of the designated calling terminal and destination terminal.
(b) If the calling terminal and the destination terminal are in a status other than idle, the NEAX2400 
IMX sends out Return Error to the AP.
2. Only digital multifunction telephone (D
term Series E)...

ND-70895 (E) CHAPTER 5
 Page 65
Revision 1.0
OFFICE DATA DESIGN
Procedure for Setting Office Data for OAI Services
3.1.3 Data Programming
Assignment
1. ASYD (System Data)
SYS1
INDEX 79
b6: 0 (OAI service is available)
2. AKYD (D
term Key Data)
Restrict a call origination from the prime line of the terminal of which answer type is
designated as automatic answer
S: Outgoing call from a prime line (0/1)
0/1: Allowed/Restricted
Deletion
1. AKYD (D
term Key Data)
Cancel restriction on a call origination from...

CHAPTER 5 ND-70895 (E)
Page 66
Revision 1.0
OFFICE DATA DESIGN
Procedure for Setting Office Data for OAI Services
3.2 Call ID Notification (SMFN for ISDN)
3.2.1 Functional Outline
This Call ID Notification function is an enhancement of both the Call Termination Notification and the
Answer Notification among Call Status Monitor Facility Notification functions of the OAI system, and
provides the User’s Application Processor for External Computer (UAP) with the caller’s information
when call termination is...

ND-70895 (E) CHAPTER 5
 Page 67
Revision 1.0
OFFICE DATA DESIGN
Procedure for Setting Office Data for OAI Services
4. When an incoming call terminates from ISDN network, ISDN caller’s number information
(subscriber’s number and sub-address) is provided from the central office in the following format.
Subscriber number is maximum 33 digits, and the sub-address is maximum 20 digits, and they are
separated by the separator “*” (OBH).
3.2.3 Data Programming
1. Assignment
ASYD (System Data)
SYS1
INDEX 79
b6:...

CHAPTER 5 ND-70895 (E)
Page 68
Revision 1.0
OFFICE DATA DESIGN
Procedure for Setting Office Data for OAI Services
3.3 MWL Control (SSF) STEP-1
3.3.1 Functional Outline
This function allows the Application Program (AP) to provide a single-line telephone equipped with
Message Waiting Lamp (MWL) or a Dterm with the following Message Waiting (MW) services by the
OAI Service Set Facility (SSF).
1. MW Setting (Turning MW Lamp On)
2. MW Resetting (Flashing MW Lamp)
3. MW CANCEL (Turning MW Lamp Off)
4. LCD...

ND-70895 (E) CHAPTER 5
 Page 69
Revision 1.0
OFFICE DATA DESIGN
Procedure for Setting Office Data for OAI Services
3.3.2 Using Conditions
1. Normal and abnormal operating sequences pertaining to the basic connection of the SSFR are as
described below.
[Normal Sequence]
[Abnormal Sequence]
Terminal (Dterm)NEAX2400 IMXComputer (AP)
SSFR Activated
Return Result
Received Information 
Analysis
Service Set/Cancel
Terminal (Dterm)NEAX2400 IMXComputer (AP)
SSFR Activated
Return Result
Received Information...

CHAPTER 5 ND-70895 (E)
Page 70
Revision 1.0
OFFICE DATA DESIGN
Procedure for Setting Office Data for OAI Services
2. This service cannot be used simultaneously with other MW control services (VMM/MCI: Message
Center Interface/Message Waiting from Station, ATTCON and MAT).
3. The conditions for the telephone that controls MW are as follows.
 MW can be serviced only on a telephone equipped with MW lamp function.
 On a single-line telephone and/or D
term, MW lamp display position is fixed.
 On a...