NEC Neax 2400 Imx Oai System Manual

ND-70895 (E) CHAPTER 3
 Page 21
Revision 1.0
INSTALLATION PROCEDURE
OAI Software Installation
3. OAI Software Installation
This section explains the installation procedure for adding the OAI software to the PBX in off-line operation.
For more detailed information of program install procedure before the OAI application software install, see
“Installation Manual”.
[Operation Procedure]
STEP 1: By using MEM_HDD command, save all data to the both HDDs. 
STEP 2: Make the Standard Service Software FD link with...

CHAPTER 3 ND-70895 (E)
Page 22
Revision 1.0
INSTALLATION PROCEDURE
OAI Software Installation
STEP 6: Assign the system data written in LDM.
ASYDL SYS1
INDEX512: FPC of the self-node
When OAI system is used through the Fusion Network, this data setting is necessary at each node in the network.
INDEX513: 01 Hex (LDM usage)
INDEX515~518 b0~b7: IP address (Hex) for PBX over external LAN
Note 4
INDEX519~522 b0~b7: Subnet Mask (Hex) for PBX over external LANNote 4
INDEX523~526 b0~b7: Default Gateway Address...

ND-70895 (E) CHAPTER 3
 Page 23
Revision 1.0
INSTALLATION PROCEDURE
Upgrading OAI System from NEAX2400 ICS to NEAX2400 IMX
4. Upgrading OAI System from NEAX2400 ICS to NEAX2400 IMX
The procedure for upgrading OAI System NEAX2400 ICS to NEAX2400 IMX is shown below.
4.1 Up Grading Procedure
STEP 1: Stop the operation of the external computer by the appropriate procedure.
STEP 2: Upgrade the PBX hardware following by the Upgrade Manual for the PBX.
STEP 3: Upgrade the PBX software to install the software...

CHAPTER 3 ND-70895 (E)
Page 24
Revision 1.0
This page is for your notes. 

ND-70895 (E) CHAPTER 4
Page 25
Revision 1.0
CHAPTER 4 COMMANDS
1. General
This chapter explains the commands that are used in the NEAX2400 IMX OAI System. The contents of this
Chapter are outlined below.
 Configuration of Commands for OAI System
This section explains the construction of each command.
 Commands
This section explains the functions, parameters, and operating procedure of each command. 

CHAPTER 4 ND-70895 (E)
Page 26
Revision 1.0
COMMANDS
Configuration of Commands for OAI System
2. Configuration of Commands for OAI System
2.1 Configuration of Commands
The configuration of the commands in use in the NEAX2400 IMX OAI System is shown in Figure 4-1.
Figure 4-1   Configuration of Commands of the NEAX2400 IMX OAI System
Commands for 
BusinessCommands for 
OAI System
ASYDL
AKYD 
ARNP 
 
ASPAAADT 
ACNO 
AMNO 
AOAC 
AOKC 
LADT 
LCNOLMNO 
LOAC 
LOKC 
DFLN 
OAI System Operating Commands...

ND-70895 (E) CHAPTER 4
 Page 27
Revision 1.0
COMMANDS
Commands
3. Commands
This section explains the commands in used in the OAI System.
3.1 List of Commands
Table 4-1 shows a list of commands in use in the OAI system. As for any command other than those in the
list, refer to the Feature Programming Manual and Office Data Specification of the NEAX2400 IMX.
Note 1:Each command marked with *is used for listing up the assigned data, and thus its explanation will be
omitted.
Note 2:For this command, refer to...

CHAPTER 4 ND-70895 (E)
Page 28
Revision 1.0
COMMANDS
Commands
3.2 Outline of Commands for OAI System
The interrelation among the commands to be used in the OAI System is illustrated in Figure 4-2.
Figure 4-2   Interrelation among OAI System Commands
AKYD : This command is used to assign the function key codes (For OAI: 34 ~ 47) to the function key
positions of the Dterm.
AOKC : This command is used to assign the meaning of OAI key code assigned by AKYD command.
Note 1:Function key codes 34 ~ 47...

ND-70895 (E) CHAPTER 4
 Page 29
Revision 1.0
COMMANDS
AADT
AADT:  Assignment of Announcement/Dictation Trunks
1. Functions
This command is used to assign/delete Announcement Trunks or Dictation Trunks.
2. Precaution
When changing the LENS of the currently assigned Announcement/Dictation Trunks, delete the assigned
data first by this command, and then change the LENS by Assignment of Trunk Data (ATRK) command.
It must be remembered that, if the LENS data are deleted first by ATRK command by mistake, the...

CHAPTER 4 ND-70895 (E)
Page 30
Revision 1.0
COMMANDS
AADT
Announcement/Dictation Trunk Data Assignment Table
Disconnect Timer 0 = Impossible
1 = Possible
TRUNK
TYPE
(TYPE)
ANT/DCTMESSAGE NO. 
(NO) MESSAGE 
TIMER
(MSGT)
2 ~ 120DISCON-
NECT
TIMER
(D)
0/1CONNEC-
TION
PATTERN
(CP)
0/1WA I T I N G  
TIMER 
(WAIT)
0 ~ 30ANT/DCT 
ASSIGNED 
NO. OF 
TRUNKS
(CNT)
1 ~ 8ROUTE
NUMBER
(RT)TRUNK 
NUMBER
(TK) ANT
1 ~ 58DCT
1 ~ 5
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | |...