NEC Neax 2400 Imx Oai System Manual

							ND-70895 (E) CHAPTER 3
 Page 21
Revision 1.0
INSTALLATION PROCEDURE
OAI Software Installation
3. OAI Software Installation
This section explains the installation procedure for adding the OAI software to the PBX in off-line operation.
For more detailed information of program install procedure before the OAI application software install, see
“Installation Manual”.
[Operation Procedure]
STEP 1: By using MEM_HDD command, save all data to the both HDDs. 
STEP 2: Make the Standard Service Software FD link with the OAI Option Service Software FD, and install
it into the HDD.
When OAI system is used in the Fusion Network (OAI Terminal Anywhere), link the ACD Option Service
Software for “Agent Anywhere” with the above software FD and install it into all the nodes. (valid since the
PBX software R8)
STEP 3: Initialize the system (perform IPL, DM loading).
PROGRAM=“LOAD”
SYSTEM DATA=“OVERRIDE/LOAD”
Note:When OAI system is used through the Fusion Network [valid since Series 7400 (Release 8) software], the
UAP must be booted up after the confirmation of the establishment of the Fusion Link.
STEP 4: Change system data written in DM.
ASYD SYS1
INDEX31 - b0~b3: CM mounting capacity
Normally assign “04”.
Note 1 Note 2 Note 3
INDEX79 - b6=0 (OAI service is in service)Note 1
INDEX207 - b0 (IP in system0), b1 (IP in system1) 
Assign “1” to the corresponding bit for the IP accommodation.
INDEX241- b2=1 (Call Processing Event Notification) 
Note 1
INDEX241- b3=1 (Details of SCF Error Notification)Note 1
Note 1:
When OAI system is used in the Fusion Network, this data setting is necessary at the all nodes.
Note 2:Reset the system after changing this data from 02H (normally assigned data value for the system without
OAI service) to 04H.
STEP 5: Assign the system data written in NDM.
This data below are necessary when OAI system is used through the Fusion Network.
ASYDN SYS1
INDEX514- NDM usage
INDEX533- FPC of the node that provides VNDM
(Normally, assign the FPC of the node that has the IP)
Note 3:Assign “OG” for Series 7400 (Release 8) and later software. 
						

							CHAPTER 3 ND-70895 (E)
Page 22
Revision 1.0
INSTALLATION PROCEDURE
OAI Software Installation
STEP 6: Assign the system data written in LDM.
ASYDL SYS1
INDEX512: FPC of the self-node
When OAI system is used through the Fusion Network, this data setting is necessary at each node in the network.
INDEX513: 01 Hex (LDM usage)
INDEX515~518 b0~b7: IP address (Hex) for PBX over external LAN
Note 4
INDEX519~522 b0~b7: Subnet Mask (Hex) for PBX over external LANNote 4
INDEX523~526 b0~b7: Default Gateway Address for External LANNote 4
(This data is required when the Host is connected via gateway)
INDEX864 - b0=1 (Built-in IP is provided)
When OAI system is used in the Fusion Network (OAI Terminal Anywhere) [available since the Series 7400 (Release 8)
software], assign “1” at the node that has the IP.
INDEX864 b1 :Output the system message (4-R) when TCP-IP is normally disconnected.
0/1=Effective/Ineffective
Note 4:If the MAT or SMDR has been connected with external LAN already, this data assignment is not necessary.
STEP 7: Check the station-to-station connection and confirm no fault status occurs or system messages are
output (such as cable connection fault, LCD display fault, memory alarm fault, abnormal interrupt
etc.).
STEP 8: Program the OAI office data. Also, program the Fusion data to make ACD service effective through
Fusion network, if necessary.
STEP 9: Save the DM into the HDD by using MEM_HDD. 
						

							ND-70895 (E) CHAPTER 3
 Page 23
Revision 1.0
INSTALLATION PROCEDURE
Upgrading OAI System from NEAX2400 ICS to NEAX2400 IMX
4. Upgrading OAI System from NEAX2400 ICS to NEAX2400 IMX
The procedure for upgrading OAI System NEAX2400 ICS to NEAX2400 IMX is shown below.
4.1 Up Grading Procedure
STEP 1: Stop the operation of the external computer by the appropriate procedure.
STEP 2: Upgrade the PBX hardware following by the Upgrade Manual for the PBX.
STEP 3: Upgrade the PBX software to install the software below.
 Assortment of software for NEAX2400 IMX  
Note 1
 OAI Optional software
STEP 4: Program the following OAI commands data again.
 ASYDL  
Note 2
STEP 5: Start Up the external computer  Note 3
 hardware and software of the external computer
STEP 6: Perform the installation test.
Note 1:This software is commonly used with all types of systems. Data Memory does not have to be changed.
Note 2:For detail, see Section 3. “OAI Software Installation”.
Note 3:This procedure is not necessary for the ACD system without MIS. For more information, see Section 2.
“Cable Connections with External Computer”. The TCP Port number of the external computer has to be
changed to “60030” for NEAX2400 IMX. 
						

							CHAPTER 3 ND-70895 (E)
Page 24
Revision 1.0
This page is for your notes. 
						

							ND-70895 (E) CHAPTER 4
Page 25
Revision 1.0
CHAPTER 4 COMMANDS
1. General
This chapter explains the commands that are used in the NEAX2400 IMX OAI System. The contents of this
Chapter are outlined below.
 Configuration of Commands for OAI System
This section explains the construction of each command.
 Commands
This section explains the functions, parameters, and operating procedure of each command. 
						

							CHAPTER 4 ND-70895 (E)
Page 26
Revision 1.0
COMMANDS
Configuration of Commands for OAI System
2. Configuration of Commands for OAI System
2.1 Configuration of Commands
The configuration of the commands in use in the NEAX2400 IMX OAI System is shown in Figure 4-1.
Figure 4-1   Configuration of Commands of the NEAX2400 IMX OAI System
Commands for 
BusinessCommands for 
OAI System
ASYDL
AKYD 
ARNP 
 
ASPAAADT 
ACNO 
AMNO 
AOAC 
AOKC 
LADT 
LCNOLMNO 
LOAC 
LOKC 
DFLN 
OAI System Operating Commands
CommandsASYD 
ASYDN 
						

							ND-70895 (E) CHAPTER 4
 Page 27
Revision 1.0
COMMANDS
Commands
3. Commands
This section explains the commands in used in the OAI System.
3.1 List of Commands
Table 4-1 shows a list of commands in use in the OAI system. As for any command other than those in the
list, refer to the Feature Programming Manual and Office Data Specification of the NEAX2400 IMX.
Note 1:Each command marked with *is used for listing up the assigned data, and thus its explanation will be
omitted.
Note 2:For this command, refer to the Feature Programming Manual and Office Data Specification of the
NEAX2400 IMX.
Table 4-1 OAI System Command Table List
ABBREV. 
COMMANDCOMMAND
AADT Assignment of Announcement/Dictation Trunks
ACNO Assignment of Conversion Number Data
AKYD Assignment of Key Data for D
term
AMNO Assignment of Monitored Number
AOAC Assignment of OAI Access Code
AOKC Assignment of OAI Key Code
ARNP Note 2Assignment of Reverse Numbering Plan Data
ASPAAssignment of Specific Attendant Number
ASYD
ASYDN
ASYDLAssignment of System Data
DFLN Display of Location Free Numbering
LADT Note 1List Up of Announcement/Dictation Trunks
LCNO Note 1List Up of Conversion Number Data
LMNO Note 1List Up of Monitored Number
LOAC Note 1List Up of OAI Access Code
LOKC Note 1List Up of OAI Key Code 
						

							CHAPTER 4 ND-70895 (E)
Page 28
Revision 1.0
COMMANDS
Commands
3.2 Outline of Commands for OAI System
The interrelation among the commands to be used in the OAI System is illustrated in Figure 4-2.
Figure 4-2   Interrelation among OAI System Commands
AKYD : This command is used to assign the function key codes (For OAI: 34 ~ 47) to the function key
positions of the Dterm.
AOKC : This command is used to assign the meaning of OAI key code assigned by AKYD command.
Note 1:Function key codes 34 ~ 47 respectively correspond to OAI key codes (1 ~ 14).
AOAC : This command is used to assign the access code/operation code for the designated facility.
This command is used only when the Facility Kind (F-KIND) has been set to “3” (Open Appli-
cation Interface) by AOKC command.
Note 2:Parameters OAI Key Code (KEY-CODE), Facility Kind (F-KIND), and Operation Code (OP-CODE) are
determined by the application software to be used at each office.
3.3 Items to Be Explained by Each Command
Each command is described by the following items.
Command : The name implies the command and its functions.
(1) Functions : This item outlines the command functions.
(2) Precaution : This item explains precaution for use of the command.
(3) Parameters : This item explains the meaning of the information (parameters) of the data of
the command.
(4) Related Commands : This item specifies other command or commands pertaining to the same data,
assignment/deletion/change/display/list up of the details of that specific data.
NEAX2400 IMX
DLC/ELC
AKYD 
AOKC 
AOACASDT
AKYDExternal Computer
ASYD
ARNPIPCommand Name : Commands for NEAX2400  
ASYD 
ARNP 
ASDT 
AKYD: Assignment of System Data 
: Assignment of Reverse Numbering Plan Data 
: Assignment of Station Data 
: Assignment of Dterm
Key Data 
						

							ND-70895 (E) CHAPTER 4
 Page 29
Revision 1.0
COMMANDS
AADT
AADT:  Assignment of Announcement/Dictation Trunks
1. Functions
This command is used to assign/delete Announcement Trunks or Dictation Trunks.
2. Precaution
When changing the LENS of the currently assigned Announcement/Dictation Trunks, delete the assigned
data first by this command, and then change the LENS by Assignment of Trunk Data (ATRK) command.
It must be remembered that, if the LENS data are deleted first by ATRK command by mistake, the data
currently assigned by this AADT command are automatically deleted.
3. Parameters
TYPE : Announcement Trunk (ANT), Dictation Trunk (DCT)
NO. : Message Number
D : Disconnect Timer (0/1); Valid when TYPE = ANT
0: Impossible (Repeat)
1: Possible (Disconnect by MSGT)
MSGT : Message Timer (2 ~ 120 sec., 2-sec. interval when shorter than 30 sec., 8-sec. interval 
when longer than 30 sec.)
CP : Connection Pattern   
Note
0: Multiple Connection
1: Single Connection
WAIT : Waiting Timer (0~30 sec., 2-sec. interval)   
Note
Note:
Available only when the system data is programmed that the DAT control function is available (ASYD,
SYS1, INDEX449, b2=1).
CNT : Number of ANT/DCT Trunks assigned or to be assigned (1 ~ 8)
RT : R o u t e  N u m b e r
TK : Trunk Number
4. Related Commands
List Up : LADT 
						

							CHAPTER 4 ND-70895 (E)
Page 30
Revision 1.0
COMMANDS
AADT
Announcement/Dictation Trunk Data Assignment Table
Disconnect Timer 0 = Impossible
1 = Possible
TRUNK
TYPE
(TYPE)
ANT/DCTMESSAGE NO. 
(NO) MESSAGE 
TIMER
(MSGT)
2 ~ 120DISCON-
NECT
TIMER
(D)
0/1CONNEC-
TION
PATTERN
(CP)
0/1WA I T I N G  
TIMER 
(WAIT)
0 ~ 30ANT/DCT 
ASSIGNED 
NO. OF 
TRUNKS
(CNT)
1 ~ 8ROUTE
NUMBER
(RT)TRUNK 
NUMBER
(TK) ANT
1 ~ 58DCT
1 ~ 5
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||
|| | | | | ||