Home > NEC > Communications System > NEC Neax 2400 Imx Oai System Manual

NEC Neax 2400 Imx Oai System Manual

    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2400 Imx Oai System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							ND-70895 (E) CHAPTER 4
     Page 51
    Revision 1.0
    COMMANDS
    ASYD
    System Data Assign Table (1)
    SYSTEM
    DATA
    TYPE
    (SYS)SYSTEM 
    DATA  
    INDEX 
    (INDEX)
    0 – 255DATA
    (DATA)
    00– FF
    (Hex)BIT 
    CORRE-
    SPONDING 
    DATA SYSTEM DATA CONTENTS
    DATA
    0/1BIT
    449b
    0SCF Call origination from the first party notification
    0/1 = Ineffective/Effective
    b
    1Not used
    b
    2Access to Announcement trunk is controlled:
    0 = by the timer, 1 = by the DAT
    b
    3Output pattern of INS information by SMFN
    0/1: HEX/ASCII
    b
    4
    Not used b5
    b6
    b7 
    						
    							CHAPTER 4 ND-70895 (E)
    Page 52
    Revision 1.0
    COMMANDS
    ASYD
    System Data Assign Table (3)
    SYSTEM 
    DATA  
    TYPE
    (SYS)SYSTEM 
    DATA 
    INDEX 
    (INDEX)
    0 – 255DATA
    (DATA)
    00– FF
    (Hex)BIT 
    CORRE-
    SPONDING 
    DATA SYSTEM DATA CONTENTS
    DATA
    0/1BIT
    315b
    0Designation of the initial mode of the card reader
    000: PB Sender 100
    001: LP Command   : Not used
    010: – 111
    011: Data channel b
    1
    b2
    0b3
    Not used 0b
    4
    0b5
    0b6
    0b7
    ~ 
    						
    							ND-70895 (E) CHAPTER 4
     Page 53
    Revision 1.0
    COMMANDS
    DFLN
    DFLN:  Display of Location Free Numbering
    29. Functions
    This command is used to check the assigned data of Location Free Numbering Service. When this
    command is activated, the assigned data are displayed on a basis of each designated station number.
    30. Precaution
    The data to be displayed by this command are those assigned from the User Application Processor (UAP)
    and thus they cannot be assigned by a command.
    31. Parameters
    [Input Parameters]
    F : Function Kind (0/1)
    LSTN : Logical Station Number (ID-No. Max. 5 digits)  
    Note 1
    TN : Tenant Number  Note 2
    PSTN : Physical Station Number (Station Number)  Note 2
    [Display Parameters]
    RSC : Route Restriction Class
    SFC : Service Feature Restriction Class
    DC : Digit Code
    Note 1:This parameter is to be entered/displayed only when F = 0.
    Note 2:These parameters are to be entered/displayed only when F = 1.
    32. Related Commands
    – 
    						
    							CHAPTER 4 ND-70895 (E)
    Page 54
    Revision 1.0
    COMMANDS
    ASYDN
    ASYDN:  Assignment of System Data in NDM
    33. Function
    This command is used to assign system data 1 and 2.
    34. Precautions
    1. This section only explains about ASYDN command for OAI system.
    2. For more details of ASYDN command, see the “Office Data Specification.”
    35. Parameters
    Refer to the following page. 
    						
    							ND-70895 (E) CHAPTER 4
     Page 55
    Revision 1.0
    COMMANDS
    ASYDN
    Note 1:
    When the all Fusion nodes in the network are used for “MULTIPLE IPs”, this data may be assigned using
    ASYDN.
    Note 2:Available since the Series 7400 (Release 8) software.
    SYSTEM 
    DATA  
    TYPE
    (SYS)SYSTEM 
    DATA 
    INDEX 
    (INDEX)
    0 – 1535DATA
    (DATA)
    00 – FF
    (Hex)BIT 
    CORRESPONDING 
    DATA
    SYSTEM DATA CONTENTS (MDATA)
    DATA
    0/1BIT
    1514 01b
    0Network Data Memory (NDM) usage. Assign 
    data “1 (the memory block is used)” for the 
    corresponding memory block. b
    1
    b2
    b3
    b4
    b5
    b6
    b7
    533b
    0
    Set up Fusion Point Code (FPC) of Node which 
    basic VNDM is mounted on. (1~253)
    Note:OAI/ACD is available in used.
    VNDM = Variable Network Data
    Memory b1
    b2
    b3
    b4
    b5
    b6
    b7
    864 b3Multiple IPs 0/1 = Out/In Service      Note 1
    870b
    0FLF Fusion Service
     0/1 = Invalid/ValidNote 2
    b
    1
    Not used b
    2
    b3
    b4
    b5
    b6
    b7
    bit Memory Block
    b0Memory Block #0
    b1Memory Block #1
    b2Memory Block #2
    b3Memory Block #3
    b4Memory Block #4 
    						
    							CHAPTER 4 ND-70895 (E)
    Page 56
    Revision 1.0
    COMMANDS
    ASYDL
    ASYDL:  Assignment of System Data into Local DM (LDM)
    36. Function
    This command is used to assign and change system data for OAI activated via FCCS.
    37. Precautions
    ASYDL command is comprised with System Data-1, INDEX 512-1535.
    This section only explains about ASYDL command for OAI System.
    38. Parameters
    Refer to the following pages. 
    						
    							ND-70895 (E) CHAPTER 4
     Page 57
    Revision 1.0
    COMMANDS
    ASYDL
    SYSTEM
    DATA
    TYPE 
    (SYS)SYSTEM
    DATA
    INDEX
    (INDEX)
    512-1535DATA 
    (DATA) 
    00 – FF 
    (Hex)BIT
    CORRESPONDING 
    DATA
    SYSTEM DATA CONTENTS
    DATA
    0/1BIT
    1512b
    0Fusion Point Code (FPC) of self node in hexadecimal.
    FPC 1-253 (01 Hex-FD Hex)
    Note:After assigning/changing the FPC, System Initialization (Non-
    Load Initialization) is required.  b
    1
    b2
    b3
    b4
    b5
    b6
    b7
    513 01b
    0Local Data Memory (LDM) usage. Assign data “1 (the memory block 
    is used)” for the corresponding memory block. 
    b
    1
    b2
    b3
    b4
    b5
    b6
    b7
    515IP Address (Hex) for PBX over External LAN
    Note:This data is valid when the PBX is connected to the external
    PC LAN.
    When 172.16.253.0 (default IP address) for the PBX is used, this data 
    setting is not necessary.
    Example:
    IP Address : 133.206.8.1
    516
    517
    518
    519Subnet Mask (Hex) for PBX over External LAN
    Note:This data is valid when the PBX is connected to the external
    PC LAN.
    When 172.16.253.0 (default IP address) for the PBX is used, this data 
    setting is not necessary.
    Example:
    Subnet Mask : 255.255.0.0
    520
    521
    522
    bit Memory Block
    b0Memory Block #0
    b1Memory Block #1
    b2Memory Block #2
    INDEX Set Hex
    515 85
    516 CE
    517 08
    518 01
    INDEX Set Hex
    519 FF
    520 FF
    521 00
    522 00 
    						
    							CHAPTER 4 ND-70895 (E)
    Page 58
    Revision 1.0
    COMMANDS
    ASYDL
    1523Default Gateway Address of External LAN
    Gateway Address (IP address of Router) of Network connecting PBX.
    Note:This data is valid when the PBX is connected to the external
    PC LAN.
    In the case of no Network Gateway, assignment data is 00 Hex.
    in Index 523 through 526.
    Example:
    Default Gateway Address : 133.206.8.254
    524
    525
    526
    SYSTEM
    DATA
    TYPE 
    (SYS)SYSTEM
    DATA
    INDEX
    (INDEX)
    512-1535DATA 
    (DATA) 
    00 – FF 
    (Hex)BIT
    CORRESPONDING 
    DATA
    SYSTEM DATA CONTENTS
    DATA
    0/1BIT
    INDEX Set Hex
    523 85
    524 CE
    525 08
    526 FE 
    						
    							ND-70895 (E) CHAPTER 5
    Page 59
    Revision 1.0
    CHAPTER 5 OFFICE DATA DESIGN
    1. General
    This chapter explains the procedure for setting the office data required in the NEAX2400 IMX OAI System. As
    for the office data setting procedure of the NEAX2400 IMX System itself, refer to the System Data Design
    Manual.
    The description of this Chapter consists of the following contents.
     Procedure for Setting Basic Office Data for OAI System
    This section explains the procedure for setting the basic office data of the OAI system.
     Procedure for Setting Office Data for OAI Services
    This section explains the procedure for setting the office data of the main services of the OAI system. 
    						
    							CHAPTER 5 ND-70895 (E)
    Page 60
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Basic Office Data for OAI System
    2. Procedure for Setting Basic Office Data for OAI System
    The procedure for setting the office data for OAI system is explained in the following.
    2.1 Data for OAI System
    1. ASYD/ASYDL
    ASYD-SYS1 INDEX31 - b0 ~ 3 : CM mounting capacity (Normally Assign “04”.)
    INDEX79 - b6 = 0 (OAI service is in service)
    INDEX207 - b0 (IP in system 0), b1 (IP in system 1)
    Assign “1” to the corresponding bit for the IP accommodation.
    INDEX241 - b2 = 1 (Call Processing Event Notification)
    INDEX241 - b3 = 1 (Details of SCF Error Notification)
    ASYDL-SYS1 INDEX513 : 01 Hex (LDM usage)
    INDEX515~518 : IP address (Hex) for PBX over External LAN
    INDEX519~522 : Subnet Mask (Hex) for PBX over External LAN
    INDEX523~526 : Default Gateway Address for External LAN
    (This data is required when the Host is connected via gateway)
    INDEX864 - b0 = 1 (Built-in IP is provided)
    INDEX864 b1 : Output the system message (4-R) when TCP-IP is normally 
    disconnected.
    0/1 = Effective/Ineffective
    2. ARNP (Reverse Numbering Plan Data)
    If necessary, assign the self office code when assigning office information within a message of
    the facility 
    						
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2400 Imx Oai System Manual