Home > NEC > Communications System > NEC Neax 2400 Imx Oai System Manual

NEC Neax 2400 Imx Oai System Manual

    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2400 Imx Oai System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							ND-70895 (E) CHAPTER 5
     Page 71
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Office Data for OAI Services
    3.3.3 Data Programming
    Assignment
    1. ASYD (System Data)
    SYS1
    INDEX 77
    b2: 0 (MW Lamp Refresh Control is in service)
    INDEX 179
    b6: 0 (OAI services are provided)
    2. ARPC (Remote Point Code for Centralized Service)
    For providing centralized services at the Message Center within a No. 7 CCIS Network,
    assign the point codes for the remote offices belonging to the main office
    CSN: Centralized Service Item No. (1 ~ 7)
    1: Message Center
    CNT: Number of Remote Office Point Codes (1 ~ 32)
    RPC: Remote Office Point Code (1 ~ 16367)
    Deletion
    1. ARPC (Remote Point Code for Centralized Service)
    Delete the point codes of the remote offices belonging to the main office
    2. ASYD (System Data)
    SYS1
    INDEX 77
    b2: 1 (MW Lamp Refresh Control is not in service)
    INDEX 179
    b6: 1 (OAI services are not provided) 
    						
    							CHAPTER 5 ND-70895 (E)
    Page 72
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Office Data for OAI Services
    3.4 TCP/IP Address (Assignment from MAT)
    3.4.1 Functional Outline
    In an OAI system to be connected with the host computer via the Ethernet, this function allows use of
    TCP/IP port with the self internet address (TCP/IP address) of the NEAX2400 IMX assigned from the
    MAT.
    Also, whether system message “4-R” (IOC card for the host computer is faulty) is to be output or not
    when the connection with the host computer has been normally disconnected can be selected by switch
    setting on the Interface Processor (IP).
    3.4.2 Using Conditions
    1. Due to the hardware limitation, only one physical TCP/IP port can be accommodated per system.
    2. Basic Value of TCP/IP Address is “172.16.253.0”.
    3. The TCP/IP addresses (A, B, C, D) that cannot be used by this function are as follows.
    Classes A, B, and C can be used. Note that Host Number = 0 cannot be used. (Conditions  [1] ~ [3].
    Classes D and E cannot be used. (Condition [4])
    Class A: [1] 0 A 127→A, 0, 0, 0
    Class B: [2] 128 A 191→A, B, 0, 0 (0 B 255)
    Class C: [3] 192 A 223→A, B, C, 0 (0 B 255, 0 C 255)
    Class D, E: [4] 244 A→A, B, C, D (0 B 255, 0 C 255, 0 D 255)
    4. System message “4-R” output can be stopped by switch setting on the System Data only when TCP
    connection has been disconnected (Normal) (ERRK=01).<
    <
    
    						
    							ND-70895 (E) CHAPTER 5
     Page 73
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Office Data for OAI Services
    3.4.3 Data Programming
    TCP/IP Address Assignment
    1. Assignment
    ASYDL (System Data (LDM))
    Assign TCP/IP address
    SYS1
    INDEX 515 ~ 518
    2. Deletion
    ASYDL (System Data (LDM))
    Delete TCP/IP address
    SYS1
    INDEX 515 ~ 518
    Stopping the system message of “4-R”
    1. Assignment
    ASYDL (System Data (LDM))
    SYS1
    INDEX 864
    b1 = 1 (The system message (4-R) is not output when TCP/IP connection is normally
    disconnected.)
    2. Deletion
    ASYDL (System Data (LDM))
    SYS1
    INDEX 864
    b1 = 0 
    						
    							CHAPTER 5 ND-70895 (E)
    Page 74
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Office Data for OAI Services
    3.5 Name Display
    3.5.1 Functional Outline
    This service is for displaying information (user’s name, station number, etc.) on the LCD of Dterm.
    1. Catch internal call
    2. Catch Forwarding Call from Call Forwarding Busy Line, Call Forwarding Absent, Call Forwarding
    Don’t Answer, Station Hunting, or etc..
    3.5.2 Using Conditions
    1. Maximum 16 digits of user’s information can be displayed on LCD according to internal numbers.
    2. What is available for this service to display, is alphabet, digit, sign or etc..
    3. For administrating user’s information clearly, it is not available to use both “Name Display Service”
    which is assigned by ANDD command and “OAI Service” at same time.
    4. It is not available to use both 8-digit Display Service and 16-digit Display Service at same time. For
    changing from 8-digit Display Service to 16-digit Display Service, can be changed by using
    “System Data”.
    5. There are limitations below for 16-digit Display Service.
     User’s information can not be displayed on the top line of LCD.
     User’s information is displayed from the left side of bottom line and if the information is less than
    16-digit, the rest of frames will be blank.
     It is not able to set multi-line on this D
    term.
    6. There is a limitation below for 8-digit Display Service.
     User’s information is displayed from the middle of top line and if the information is less than 8
    digits, the rest of frames will be blank. And the bottom line will display the clock.
    7. If the user’s information is not assigned, normally station number will be displayed.
    8. There is no guarantee for the user’s information since you change from 16-digit Display Service to
    8-digit Display Service.
    9. The service will be effective, if either of calling party or called party has D
    term which has the LCD. 
    						
    							ND-70895 (E) CHAPTER 5
     Page 75
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Office Data for OAI Services
    3.5.3 Data Programming (Set up from User’s Application)
    1. Assignment
    ASYD
    SYS1
    INDEX31: 04: mount capacity of Common Memory (CM) 4Mbyte
    INDEX78
    b0 = 1 (Intermediate Station Number Display is in service)
    b1 = 1 (Service Assortment Display is in service)
    b3: Dial Number Display 0/1: Out/In service
    b5 = 1 (Name Display Service is in service)
    INDEX79
    b5: Expanded Name Display (displaying 16-digit) 0/1: Out/In service
    b6 = 0 (OAI Service is in service)
    INDEX241
    b1: Name Display 0/1: 8-digit/16-digit
    2. Deletion
    ASYD
    SYS1
    INDEX78
    b0: Intermediate Station Number Display 0/1: Out/In service
    b1: Service Assortment Display 0/1: Out/In service
    b3: Dial Number Display 0/1: Out/In service
    b5 = 0 (Name Display service is Out)
    INDEX79
    b5: Expanded Name Display (displaying 16-digit) 0/1: Out/In service
    b6 = 1 (OAI Service is Out)
    INDEX241
    b1 = 0 (Name Display is displaying 8-digit) 
    						
    							CHAPTER 5 ND-70895 (E)
    Page 76
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Office Data for OAI Services
    3.6 Inter Node Name Display
    3.6.1 Functional Outline
    Name Display Service is available between the network.
    Name Display Service means for the facility of displaying letters (alphabet and etc.) on LCD of the
    D
    term.
    Catching call from other internal line
    3.6.2 Using Conditions
    1. When Calling party is calling Called party, the LCD of Calling party will display Called party’s
    name information by the internal number.
    2. If there is no information of Calling party or Called party, only the number of Calling party or Called
    party’s will be displayed.
    3. When there are both 8-digit and 16-digit of Inter Node Name Display Service in same Node, Calling
    party/Called party’s name will be shown as below.
    4. When Name Display Service is set up for 16-digit, it will be unable to set up multi-line at the D
    term.
    5. When Calling party reaches CCIS call to Called party by using D
    term Sub-Line, the display of
    Called party will display the Sub-Line name of Calling party. (Only for 8-digit)
    6. The Name Display of Called party indicates prime line only for Both of 8-digit and 16-digit.
    7. What is available to display for this service, are alphabet, figure, sign and etc....
    8. Assign the Name Information Data, based on each D
    term LEN, by using the Free Location Facility
    available on the user’s application.
    9. The route which is set up Inter Node Display Service and the route which is not set up Inter Node
    Display Service should be separated from each other.
    10. Even Dial Number Display Service is activate, the dial number won’t be displayed between the Inter
    Node.
    Inter Node Name Display
    Service
    Calling Party → Called partyDisplay of Calling party’s name Display of Called party’s name
    16-digit 
    → 8-digit 16-digit on Center Line
     (right side of 8-digit will be blank)8-digit on Top Line
     (First 8-digit will be displayed)
    8-digit 
    → 16-digit 8-digit on Top Line
     (First 8-digit will be displayed)16-digit on Center Line
    (right side of 8-digit will be blank)
    8-digit 
    → 16-digit → 8-digit 8-digit on Top Line 8-digit on Top Line
    16-digit 
    → 8-digit → 16-digit 16-digit on Center Line 8-digit on Center Line 
    						
    							ND-70895 (E) CHAPTER 5
     Page 77
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Office Data for OAI Services
    11. The objected terminal of Name Display Service is only Dterm which has LCD.
    12. “Office Code” + “Station Number” is normally displayed. However, when use of a logical number
    is specified, only the logical number without an office code is displayed. (ONE CCIS network is
    assigned only one logical number.)
    13. When a call has been transferred by “Call Forwarding All Outside Line Call” or “Call Forwarding-
    Busy Outside Line Call”, the LCD of Calling Party’s D
    term will display “Name Information” of
    Called party, instead of dialed number.
    14. When you call to a party by the way of a party which doesn’t have Inter Node Name Display Service
    in CCIS network, or the other Node of CCIS network, the Name Display Service will not serve.
    15. This service can not be used in conjunction with ISDN Information Transfer-CCIS Service.
    16. Those below are the Inter Node Services which are able to serve Inter Node Name Display.
    Voice Call
     Inter Node Call Forwarding All Call
     Inter Node Call Forwarding Busy Line
     Inter Node Call Forwarding No Answer
     Inter Node Camp On (Only for calling)
     Message Reminder (Only for outgoing)
    17. Those below are the Self Node Services including CCIS Trunk which are able serve Inter Node
    Name Display.
    Call Pick Up
     Ringing for Call Hold
     Answering for call park
     Call waiting
     Catching call from UCD Queuing
    18. For the terminal which is able to serve Inter Node Display Service, please see the Item of Name
    Display Service.
    B Office
    C Office
    E OfficeA Office
    D Office
    (Name Display
    - System - CCIS is
    not serviced)
    CCIS
    CCISCCIS
    CCIS
    CCIS (1)
    (2)
    In the case of (1): Name Display is serviced.
    In the case of (2): Name Display is not serviced.
    In the case of (3): Name Display is not serviced. 
    						
    							CHAPTER 5 ND-70895 (E)
    Page 78
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Office Data for OAI Services
    3.6.3 Data Programming (Set up from User’s Application)
    Assignment 
    Those below are explanation of the Assignment according to Name Information which is set up
    from User’s Application.
    1. ASYD
    SYS1
    INDEX 78
    b5 = 1 (Name Display Service is in service)
    b3: Dial Number Display 0/1: Out/In service
    INDEX 79
    b6 = 0 (OAI Service is in service)
    INDEX 241
    b1: Name Display 0/1: 8-digit/16-digit displaying
    2. Route Class Data (ARTD)
    Change the Route Class Data of CCIS Trunk
    Busy Line Service (BT): 1 (Active)
    Number Display Designation (DPLY): 1(Called Party Number Display)
    ISDN Output Information (CI): 0 (Existing)
    Inter Node Display Service (IND): 1 (In service)
    Deletion
    1. Route Class Data (ARTD)
    Delete the Route Class Data of CCIS Trunk
    Busy Line Service (BT): 0/1 (Out/In Service)
    Number Display Designation (DPLY): 0/1(-/Called Party Number Display)
    ISDN Output Information (CI): 0 ~ 15
    Inter Node Display Service (IND): 0 (Out)
    2. ASYD
    SYS1
    INDEX 78
    b5: Name Display Service 0/1: Out/In service
    b3: Dial Number Display 0/1: Out/In service
    INDEX 79
    b6 = 1 (OAI Service is not in service)
    INDEX 241
    b1 = 0 (Name Display 8-digit) 
    						
    							ND-70895 (E) CHAPTER 5
     Page 79
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Office Data for OAI Services
    3.7 OAI Fusion
    Main advantages of OAI Fusion fall down into the following. OAI Fusion systems can be divided into the
    following two types: 
     OAI Terminal Anywhere
     Multiple IPs
    3.7.1 OAI Terminal Anywhere
    3.7.1.1 Functional Outline
    In this configuration (OAI Terminal Anywhere), the OAI terminal can be installed in any Fusion node
    whether the node has the IP or not (those OAI terminals in multiple nodes are controlled by one IP).
    In other words, the facilities in multiple nodes (any Fusion node whether the node has the IP or not)
    are controlled by one IP. (“Facility” which can be used through the Fusion Network varies in “the OAI
    application”.)
    3.7.1.2 Using Conditions
    (a) The Node that accommodates the IP is one node only in a Fusion network. 
    (b) Telephone Number (max. 5 digits) is used for the station number type to activated OAI system
    through Fusion network.
    (c) Logical Route is used for the route type to activate OAI system through Fusion network.
    FAC I L I T Y
    Node B
    OAI TerminalsFACILITY
    Node A
    UAPIP
    FAC I L I T Y
    FCCS
    FCCSFCCS
    OAI Terminals
    OA I  Ter mi n al s
    Node C 
    						
    							CHAPTER 5 ND-70895 (E)
    Page 80
    Revision 1.0
    OFFICE DATA DESIGN
    Procedure for Setting Office Data for OAI Services
    (d) The node that accommodates the IP must be initialized when all the other nodes are in on-line
    mode.
    (e) The User’s Application (UAP) must be booted up after the confirmation of the establishment
    of the Fusion link.
    (f) When you add a node/nodes to the network, you have to initialize the node that accommodates
    the IP.
    3.7.1.3 Data Programming
    STEP 1: Assignment of System Data
    (Data for OAI Fusion)
    ASYDL/ASYDN
     The data below must be set to all nodes in the network
    (a) ASYDL-SYS1 INDEX512 b0~7: Assign the self-Fusion Point Code (self-FPC) at each node.
    (1~253)
    INDEX865 b0~7: FPC of the node providing IP
    Note:Assign 0 for the node that providing IP in the self-node only.
    (b) ASYDN-SYS1 INDEX514 : NDM usage
    INDEX533 : FPC number of the node that has the standard VNDM 
    (1-253)
    STEP 2: Data programming procedures other than STEP 1 are the same as that of the non-Fusion system.
    Therefore, only notification or condition of the data programming is shown below in this section. 
    (a) ASYD/ASYDL
     The data below are set to the node that accommodates IP
    ASYD - SYS1, INDEX207, b0:1=IP0 is used
    SYS1, INDEX207, b1:0/1=IP1 is not used/used
    ASYDL - SYS1, INDEX864, b0:1=Built-in IP is used
     The others are set to all nodes in the Fusion network.
    (b) Following are the notification Fusion data programming with commands below. 
    For the following commands, assign data by the corresponding commands written in NDM.
     AMNON (AMNON is used in place of AMNO)
     ACNON (ACNON is used in place of ACNO)
     AADTN (AADTN is used in place of AADT)
    (c) The AKYD, AOKC command data are set to all nodes in Fusion network to be provided OAI system.
    (For these commands, assign data by the corresponding commands written in DM) 
    						
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2400 Imx Oai System Manual