NEC Neax 2400 Imx Oai System Manual

ND-70895 (E) CHAPTER 4
 Page 41
Revision 1.0
COMMANDS
AOKC
Table of Operation Codes
OPERATION CODE REMARKS
128 (0080): MSF
191 (00BF): MSFOAI
(Terminal Mode Set Facility)
192 (00C0): TMF
255 (00FF): TMFOAI
(Terminal Multiple Information Transfer Facility) 

CHAPTER 4 ND-70895 (E)
Page 42
Revision 1.0
COMMANDS
ASPA
ASPA:  Assignment of Specific Access Code
24. Functions
This command is used to assign/delete/display each data which respectively determines what kind of
service should be executed and/or which route should be used, etc. when a special access code, C.O. line
access code or Tie-Line access code has been dialed.
25. Precaution
(a) For the details of special access code data, refer to the description of ASPA command in the Feature 
Programming...

ND-70895 (E) CHAPTER 4
 Page 43
Revision 1.0
COMMANDS
ASYD
ASYD:  Assignment of System Data
27. Functions
This command is used to assign System Data 1, 2, and 3.
28. Precaution
For the details of the system data, refer to the description of ASYD command in the Office Data
Specification for the NEAX2400 IMX. 

CHAPTER 4 ND-70895 (E)
Page 44
Revision 1.0
COMMANDS
ASYD
System Data Assign Table (1)
The Office Data Sheets of this ASYD command are provided only for the data to be assigned in the OAI System.
Use these Office Data Sheets together with those for ASYD command of the NEAX2400 IMX.
SYSTEM 
DATA  
TYPE
(SYS)SYSTEM 
DATA  
INDEX 
(INDEX)
0 – 255DATA
(DATA)
00– FF
(Hex)BIT 
CORRE-
SPONDING 
DATA SYSTEM DATA CONTENTS
DATA
0/1BIT
1190b
0
Not used 0b
1
0b2
0b3
0b4
b5
Call Event Transfer Facility (ETF) Call...

ND-70895 (E) CHAPTER 4
 Page 45
Revision 1.0
COMMANDS
ASYD
System Data Assign Table (1)
SYSTEM 
DATA 
TYPE
(SYS)SYSTEM 
DATA 
INDEX 
(INDEX)
0 – 255DATA
(DATA)
00– FF
(Hex)BIT 
CORRE-
SPONDING 
DATA SYSTEM DATA CONTENTS
DATA
0/1BIT
131 040b
0Equipped capacity of the Common Memory (CM): 1 ~ 4 Mbyte
Assign “6” Hex. when FLF Fusion service is used.
(Available since the PBX software R8) 0b
1
1b2
0b3
0b4
Not used 0b5
0b6
0b7
47b
0Traffic Measurement Indication
0/1 = CCS Indication/Erlang Indication
b
1
Timer...

CHAPTER 4 ND-70895 (E)
Page 46
Revision 1.0
COMMANDS
ASYD
170b
0Called Number Display when forwarding to Attendant Console
0/1 : Out/In service
b
1Flashing display of Line Lockout on Attendant Console BLF
0/1 : In service/Out
b
2
Route No. Display on Attendant Console
b
3
0b4One digit dialing instead of SHF (DP TEL only)
0/1 : Not required/Required
b
5
Priority order for answering via ANSWER key
0 : Priority according to Type of Call
1 : Priority according to the order call termination
b
6Connection of...

ND-70895 (E) CHAPTER 4
 Page 47
Revision 1.0
COMMANDS
ASYD
Note 1:
When the bit is set to “0” the bottom line display of the Message Waiting Enhance Display Service becomes
invalid.
Note 2:If, at an office in service with this bit set to “1” (No OAI Service is Provided), the bit value is to be changed
to “0” (OAI Service is Provided).
1781b
0
Calling and Intermediate Station Number indication
(Dterm and ATTCON)
0/1: Out/In service
(Always assign “1”)
1b
1
Kind of Service Class indication (Dterm)
0/1:...

CHAPTER 4 ND-70895 (E)
Page 48
Revision 1.0
COMMANDS
ASYD
System Data Assign Table (1)
SYSTEM
DATA
TYPE
(SYS)SYSTEM 
DATA  
INDEX 
(INDEX)
0 – 255DATA
(DATA)
00– FF
(Hex)BIT 
CORRE-
SPONDING 
DATA SYSTEM DATA CONTENTS
DATA
0/1BIT
1800b
0Not used
b
1Message Reminder Service-Key used for Message Deletion (Dterm)
0/1 = # key/* key
b
2Fixed to “0”
b
3
TCF (I) : LCD Display Control
0: Top Line 16-digits display control
1: Second Line 16-digits display control
0b
4
Not used 0b5
0b6
0b7 

ND-70895 (E) CHAPTER 4
 Page 49
Revision 1.0
COMMANDS
ASYD
System Data Assign Table (1)
SYSTEM
DATA
TYPE
(SYS)SYSTEM 
DATA  
INDEX 
(INDEX)
0 – 255DATA
(DATA)
00– FF
(Hex)BIT 
CORRE-
SPONDING 
DATA SYSTEM DATA CONTENTS
DATA
0/1BIT
1 207b
0No. 0 CPU Mounted Status of IP00/1:Not mounted/Mounted
b
1No. 1 CPU Mounted Status of IP00/1:Not mounted/Mounted
0b
2
Not used 0b
3
0b4
0b5
0b6
0b7 

CHAPTER 4 ND-70895 (E)
Page 50
Revision 1.0
COMMANDS
ASYD
Note:
This timer data is exclusively for the function for batch transfer (TMF) of OAI dial number from a single-
line telephone set. Therefore, this timer data is invalid for TMF from a Dterm.
1241b
0Data Port Chime Control by SCF
0/1: To be controlled/Not to be controlled
b
1Name Display Service
0/1: 8 digits/16 digits
b
2Call Status Monitor Facility Notification (SMFN)
0/1: Invalid/Valid
b
3SCF Return Error Detail Notification
0/1:...