NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 967
Service Display - Dterm - CCIS S-53D
S-53D  Service Display - Dterm - CCIS
General Description
This feature allows a Dterm user to receive LCD displays corresponding to the various features as they are initiated.
Operating Procedure
Each display is automatically generated when a service feature is initiated.
Service Conditions
1. Each display is controlled by system data and is produced accordingly. A display may be allowed or
denied...

NEAX2400 IMX Feature Programming Manual
Page 968ND-70184 (E), Issue 3
S-54 Simultaneous Voice and Data Transmission - CCIS
S-54 Simultaneous Voice and Data Transmission - 
CCIS
General Description
This feature allows a voice signal and a digital data signal of up to 56 Kbps to be transmitted simultaneously through
CCIS, via a Dterm equipped with a Data Adapter. Voice and data calls can be placed to different locations. 
Operating Procedure
To place a data call to a terminal already connected by a voice...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 969
Simultaneous Voice and Data Transmission - CCIS S-54
Service Conditions (cont’d)
4. If the Dterm DTX button is pressed when connected station-to-station within the CCIS network, the voice
line connection is switched to MODEM POOLING - CCIS [M-39] from the Dterm Data line.
Interactions
1. It is recommended that the numbering plan be set up so that voice numbers occupy one level and data
levels occupy another. Therefore, a voice number...

NEAX2400 IMX Feature Programming Manual
Page 970ND-70184 (E), Issue 3
S-54 Simultaneous Voice and Data Transmission - CCIS
Programming (cont’d)
19: TMM
20: PSM
23: ISDN Terminal
27: Eight Conference Equipment
RSC: Route Restriction Class (0-15).
For assignment of RSC, ARSC command.
SFC: Service Feature Class (0-15) 
For assignment of SFC, ASFC command.
STEP 3:ANPD - Reserve a number level for station access. Assign for Normal (N), Hooking (H) and Busy (B).
Assign NND in accordance with a predetermined...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 971
Single-Digit Station Calling - CCIS S-55
S-55  Single-Digit Station Calling - CCIS 
General Description
This feature allows single-digit station numbers to be assigned.
Operating Procedure
1. Lift the handset; receive dial tone,
2. Dial the single-digit station code,
3. The called station will ring.
Service Conditions
1. The single-digit number must not duplicate the first digit of:
a.) Trunk Access Codes
b.) Feature Access Codes
c.)...

NEAX2400 IMX Feature Programming Manual
Page 972ND-70184 (E), Issue 3
S-56 Station-Controlled Conference - CCIS
S-56 Station-Controlled Conference - CCIS
General Description
This feature allows any PBX station to establish a conference through CCIS. The conference can be any combination
of stations and trunks (on-network and off-network parties).
Operating Procedure
To establish a conference call: 
1. The user wishing to establish the conference (Conference Leader) calls each party to be included and...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 973
Station-Controlled Conference - CCIS S-56
Programming
ASHP - Assign a Pilot hunting group using eight of the PA-16LCBE line circuits. These ports are
connected to an external conference unit, MMCB Model 37008. Make sure that SFI 4 is denied to the
conference stations. 

NEAX2400 IMX Feature Programming Manual
Page 974ND-70184 (E), Issue 3
S-57 Station-to-Station Calling - CCIS
S-57 Station-to-Station Calling - CCIS 
General Description
This feature allows any user to dial another station directly, through CCIS, without operator assistance. 
Operating Procedure
1. Lift the handset; receive dial tone.
2. Dial the desired telephone number.
Service Conditions
1. The maximum number of digits per telephone number is eight.
2. Either Calling-Party Release or First-Party...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 975
Station-to-Station Calling - Operator Assistance - CCIS S-58
S-58  Station-to-Station Calling - Operator Assistance 
- CCIS
General Description
This feature allows a user to call another station, through CCIS, with the assistance of the Attendant Console
operator.
Operating Procedure
To place a station-to-station call through the Attendant Console: 
1. Lift the handset; receive dial tone.
2. Dial the operator access code (normally...

NEAX2400 IMX Feature Programming Manual
Page 976ND-70184 (E), Issue 3
S-59 Step Call - CCIS
S-59 Step Call - CCIS
General Description
This service feature allows Inter-Office Step Call when the calling station and the called station belong to different
PBX’s in the CCIS network. 
Operating Procedure
1. While Station (a1) and (b1) are engaging in a call, Station (a2) goes off-hook and receives dial tone.
2. Station (a2) dials No. 2220 for Station (b1) and receives busy tone.
3. Station (a2) dials the...