NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 977
Step Call - CCIS S-59
Service Conditions (cont’d)
4. If a station is set for any type of CALL FORWARDING-ALL CALLS, BUSY LINE, DON’T ANSWER,
the CALL FORWARDING [C-2, C-3, C-5] will take effect. 
Programming
ASYD - System 1, Index 68, Bit 0: SHF method (Step Call becomes effective).  

NEAX2400 IMX Feature Programming Manual
Page 978ND-70184 (E), Issue 3
S-60 Synchronous Data Switching - CCIS
S-60  Synchronous Data Switching - CCIS
General Description
This feature allows a synchronous data terminal connected to a Dterm/Data Adapter to call a synchronous data
terminal connected to a synchronous Dterm/Data Adapter through the CCIS network.
Operating Procedure
To originate a synchronous data call from a Dterm equipped with a Data Adapter:
1. Press the DATA key on the Dterm. The DATA lamp...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 979
Synchronous Data Switching - CCIS S-60
Interactions (cont’d)
4. For greater detail, refer to ETI: 010, Dterm IV, V Asynchronous Data Adapter - Installation and
Programming.
5. Switched Synchronous Communication Using The DT-003 Data Module:
Typically, switched (dialed) synchronous connections are attached to computers using Half Duplex
protocols. In most cases where a Half Duplex protocol is used, the DM has to be set for Full Duplex...

NEAX2400 IMX Feature Programming Manual
Page 980ND-70184 (E), Issue 3
S-60 Synchronous Data Switching - CCIS
Interactions (cont’d)
b.) Voice and data must both be idle. Turn OFF power to the Data Module. Move the SW3 switch to
the right (ON), then turn power back ON. The Data Module will enter Menu Mode.
c.) The initial menu will appear on the DTE display. Enter “5” (Attribute data) to the INPUT NO.?
prompt. Input the parameter number (02, 03 or 10) when the INPUT NO.? prompt appears again,
then enter...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 981
Synchronous Data Switching - CCIS S-60
Programming (cont’d)
1: Feature Key
2: Multi-line Key
KD: Assign as 0. 
FKY: Feature Key Number
The feature keys, DATA TRANSFER DTX (FKY = 31), DATA (FKY = 29) must be assigned.
DISPLAY/AUTO (FKY = 30) is optional.
STEP 3:ASFC - for TEC = 13 stations, construct an SFC in which SFI 11 = 0 for DATA LINE SECURITY.
STEP 4:ARSC - Construct a Route Restriction Class that allows access to the desired...

NEAX2400 IMX Feature Programming Manual
Page 982ND-70184 (E), Issue 3
S-60 Synchronous Data Switching - CCIS
Programming (cont’d)
The following parameters will be displayed. Assign attribute data according to the following table:
No. Parameter Display Data Description
00 DTR ER Check00 DTR Check Necessary
01 DTR Check Not Necessary
01 AUT Auto Answer00 Manual Response
01 Auto Response
02 MDM No. 1 OG Modem00 Delete MDM Group No.
01-15 OG Modem Group No.
03 MDM No. 2 IC Modem00 Delete MDM Group No.
01-15...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 983
Synchronous Data Switching - CCIS S-60
Programming (cont’d)
For Data Module
STEP 1:ASDT - Assign levels 1, 2, & 3 of a PA-4DTL as TEC = 16. Also assign an RSC and SFC.
STEP 2:ASFC - For TEC = 16 stations, assign an SFC that, at a minimum, SFI 11 = 0, DATA LINE
SECURITY.
STEP 3:ARSC - Construct a Route Restriction Class that allows access to the desired incoming and outgoing
routes. Those routes include PA-24DTA ACIS and CCIS routes....

NEAX2400 IMX Feature Programming Manual
Page 984ND-70184 (E), Issue 3
S-73 Supervisory Call - CCIS
S-73 Supervisory Call - CCIS
General Description
This feature allows an Attendant, in a CCIS network, to set Supervisory Call status before releasing a Central Office
call to a station. When the call is extended to a station, the loop will remain up until the called station answers. This
overrides ATTENDANT LOOP RELEASE [A-6] on a per call basis.
Operating Procedure
To activate a SUPERVISORY CALL - CCIS...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 985
Toll Restriction - 3/6-Digit - CCIS T-26
T-26  Toll Restriction - 3/6-Digit - CCIS
General Description
This feature allows the NEAX2400 IMX to restrict outgoing calls through CCIS according to specific Area and/or
Central Office codes. This restriction is determined on the basis of a three-digit Area Code or six-digit Area and
Office Code numbering plan.
Operating Procedure
No manual operation is required.
Service Conditions
1. The...

NEAX2400 IMX Feature Programming Manual
Page 986ND-70184 (E), Issue 3
T-26 Toll Restriction - 3/6-Digit - CCIS
Programming (cont’d)
See DAY/NIGHT CLASS OF SERVICE [D-15].
SYS2, Index 1, bit 3. Does TOLL RESTRICTION apply to SPEED CALLING - STATION? 0/1: Yes/
No.
SYS2, Index 1, bits 4 & 5. If TOLL DENIAL is required assign these bits as data “00”. If TOLL
DIVERSION is required assign these bits as “01”.
SYS2, Index 1, bit 7. Does TOLL RESTRICTION apply to SPEED CALLING - SYSTEM? 0/1: Yes/
No.
STEP 2:ARSC...