NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 987
Toll Restriction - 3/6-Digit - CCIS T-26
Programming (cont’d)
DC: Destination (Area) Code (Maximum 11 digits)
TDI: Restriction Data*
0: Connection is Restricted
1: Connection is Allowed
2: 3/6-Digit Toll Restriction [Go to AARP]
3: C.O. Operator Call 9 + 0.
NND: Number of Necessary Digits (Used only when TDI = 2).
Note:
TDI 4 may appear when the digits input under the DC parameter are incorrect. The switch is looking for more digits....

NEAX2400 IMX Feature Programming Manual
Page 988ND-70184 (E), Issue 3
T-26 Toll Restriction - 3/6-Digit - CCIS
Programming (cont’d)
AARP Command -
Not Required. This command is only required when TDI = 2 is assigned in ATDP.
Example 2 - RSC 2 Assignment
ATDP Command -
TDM/OG:O (Outgoing Connection)
DAY/NIGHT:D (Day)
OGRT: 1 RSC:2
DC: 92TDI:1 (Connection is Allowed)
Repeat these same assignments for Digit Codes (DC) 93 - 99 to allow all local office codes.
To allow Area Codes 718, 212, 201, & 914 repeat...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 989
Toll Restriction - 3/6-Digit - CCIS T-26
Programming (cont’d)
Note that this method of assignment allows office codes 239, 465 & 798 to any Area Code that is
assigned as TDI = 2 in ATDP.
For example, if the assignment for Area Code 718 was changed from TDI = 1 (allowed) to TDI = 2,
then the office codes 239, 465, & 798 would also be allowed for Area Code 718.
If different Office Codes are to be allowed in the 718 Area Code (for...

NEAX2400 IMX Feature Programming Manual
Page 990ND-70184 (E), Issue 3
T-26 Toll Restriction - 3/6-Digit - CCIS
Programming (cont’d)
DC: 913 TDI: 2 (Go to AARP Command)NND:3
DC: 914 TDI: 2 (Go to AARP Command)NND:3
\\\\ (Through) \\\\ 
DC: 919 TDI: 2 (Go to AARP Command)NND:3
This tells the system to check AARP tables for all Area Code restrictions.
AARP Command -
OGRT: 1 RSC: 4 FLAG: 1 DC: 808 RES: 0*
OGRT: 1 RSC: 3 FLAG: 1 DC: 213 RES: 0*
OGRT: 1 RSC: 3 FLAG: 1 DC: 408 RES: 0*
OGRT: 1 RSC: 3 FLAG: 1 DC:...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 991
Toll Restriction - 3/6-Digit - CCIS T-26
Programming (cont’d)
STEP 6:ARRC - This command provides trunk-to-trunk connection abilities according to the requirements of
the system. The applicable trunk-to-trunk will be those connections provided by parameter ARI-D-
RES direct connection. For example, REMOTE ACCESS TO THE SYSTEM [R-2] and TANDEM
SWITCHING OF TIE TRUNKS - 2/4 WIRE [T-1]. 
ICRT: Incoming Route Number
OGRT: Outgoing Route...

NEAX2400 IMX Feature Programming Manual
Page 992ND-70184 (E), Issue 3
T-27 Trunk Answer from Any Station - CCIS
T-27  Trunk Answer from Any Station - CCIS
General Description
This feature allows any station not restricted from incoming calls to answer incoming calls when the network is in
Night mode.
When this feature is activated, incoming Central Office calls will activate a common TRUNK ANSWER FROM
ANY STATION (TAS) signal. By dialing a specified code, any station may answer the call and extend it to...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 993
Trunk Answer from Any Station - CCIS T-27
Interactions
The system must be in the Night Mode for TAS to operate. Take into consideration the type of ATTENDANT
CONSOLE [A-3] system that is in service. Take special care when setting the resistance value via switch settings
on the PA-CS07 ATTENDANT CONSOLE [A-3] Circuit Card.
Programming
STEP 1:ASYD - SYS1, Index 68, bit 2. Type of TAS ringing; 0/1: Continuous/Interrupted.
SYS1, Index 77,...

NEAX2400 IMX Feature Programming Manual
Page 994ND-70184 (E), Issue 3
U-5 Uniform Numbering Plan - CCIS
U-5  Uniform Numbering Plan - CCIS
General Description
In a CCIS network, a Uniform Numbering Plan enables a user to call any other station in the network using a
Uniform Numbering system. Two alternative numbering plans are provided:
 In the first plan, the user dials a four or five-digit station number. The node in which the called station is 
located is identified by either the first digit or the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 995
Uniform Numbering Plan - CCIS U-5
Interactions
If seven-digit Uniform Numbering Plans are used, an access code to the CCIS network may be added. Thus, a total
of eight digits will be dialed. For example, a user in Illinois wishes to reach a CCIS station number (753-4526) in
New York. Two options exist for network setup. The digit 8 may be programmed as a CCIS network access code,
such as a Least Cost Routing access code. The user then...

NEAX2400 IMX Feature Programming Manual
Page 996ND-70184 (E), Issue 3
U-5 Uniform Numbering Plan - CCIS
Programming (cont’d)
STEP 9:AOP R - The AFRS command designates the dialing sequence and the OPR to be selected. The AOPR
defines the routes and in what order these routes will be selected. In this case, the DTI routes will be
assigned. Also, it may be desirable to include DDD trunks as an overflow. Assign the following
parameters: 
TDC NO. - Time-of-Day Pattern Change. Usually, this parameter does NOT...