NEC Neax 2400 Imx Business Features And Specifications

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 21
Attendant Night Transfer A-19
A-19 Attendant Night Transfer
General Description
When the ATTENDANT CONSOLE [A-3] is in night mode, any operator calls (dial 0 calls) are automatically
routed to a predetermined night station.
Operating Procedure
To answer night call:
1. The user dials the operator call code; receives ringback tone.
2. An operator call is automatically transferred to the night answer station.
3. The calling party...

NEAX2400 IMX Business Features and Specifications
Page 22NDA-24221, Issue 3
A-19 Attendant Night Transfer
Service Conditions (cont’d)
13. Operator calls after Consultation Hold is not transferred to the Night Station.
14. Individual Attendant calls are not transferred to the Night Station assigned by ATTENDANT NIGHT
TRANSFER.
15. The Night Station can set CALL FORWARDING - ALL CALLS - OUTSIDE [C-28], CALL
FORWARDING - BUSY LINE - OUTSIDE [C-60], and CALL FORWARDING - DONT ANSWER -
OUTSIDE [C-74].
16....

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 23
Authorization Code A-20
A-20 Authorization Code
General Description
An AUTHORIZATION CODE is a numerical code dialed by users (up to 10 digits), which will override the station
CLASS OF SERVICE - INDIVIDUAL [C-15] for facility access restriction. 
The AUTHORIZATION CODE can be masked on the D
term display if necessary using the AUTHORIZATION
CODE DISPLAY ELIMINATION [A-99].
When a wrong code is received from a station/trunk,...

NEAX2400 IMX Business Features and Specifications
Page 24NDA-24221, Issue 3
A-20 Authorization Code
Service Conditions
1. A maximum of 10 digits for AUTHORIZATION CODE can be dialed, and 8 digits will be registered on
STATION MESSAGE DETAIL RECORDING [S-10].
2. The maximum number of AUTHORIZATION CODES is 4,000. This number is dependent upon system
configuration.
These specifications are based on the digits being assigned as follows:
1st digit: A (when A equals a unique digit from 0 - 9)
2nd digit:  B -...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 25
Authorization Code A-20
Interactions (cont’d)
5. There are no restrictions regarding the first digit of AUTHORIZATION CODES, except what is
programmed in AMND. Tenant 0 does not conflict with the PBX numbering plan. This is true when
separate tenant tables are provided. If common tenant tables are used, a conflict between LCR(S) and
OGC(A), used with SMDR, will occur.
Note:The access code to the service feature AUTHORIZATION...

NEAX2400 IMX Business Features and Specifications
Page 26NDA-24221, Issue 3
A-21 Automatic Trunk Test
A-21  Automatic Trunk Test
General Description
The AUTOMATIC TRUNK TEST capability provides a functional test on a large number of trunks at a prearranged
time. The results of the test are reported at the MAINTENANCE ADMINISTRATION TERMINAL (MAT) [M-
18]. The test can include: Ringback Tone Test, 1 KHz Test Tone and Trunk Selection Test, by having the proper test
trunk termination at the distant office....

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 27
Authorization Code - Tie Line Incoming Routes A-29
A-29  Authorization Code - Tie Line Incoming Routes
General Description
This service feature offers an outside party the ability to enter an AUTHORIZATION CODE [A- 20] through an
incoming TIE Line trunk.
Operating Procedure
When the incoming route is restricted or when an AUTHORIZATION CODE [A-20] is always required:
1. The called number, office code, and terminal number are...

NEAX2400 IMX Business Features and Specifications
Page 28NDA-24221, Issue 3
A-29 Authorization Code - Tie Line Incoming Routes
Interactions (cont’d)
6. If ASPA, SRV: LCR (Least Cost Route Selection) / LCRS (Register Sender LCR) AH parameter is
assigned as data “1”, the request for an AUTHORIZATION CODE is determined by the ARSC
assignment of the station in relationship to the route chosen. For AUTHORIZATION CODE - TIE LINE
INCOMING ROUTES, no RSC is assigned against the incoming TIE Line, therefore,...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 29
Automatic/Manual Intercom A-30
A-30 Automatic/Manual Intercom
General Description
This feature permits multiple Dterm users to simultaneously call all the stations in a preassigned group, regardless of
their idle/busy status. An INTERCOM member can optionally override another INTERCOM station in a two-party
INTERCOM connection. This service is referred to as INTERCOM BRIDGE. INTERCOM service is separated into
two types,...

NEAX2400 IMX Business Features and Specifications
Page 30NDA-24221, Issue 3
A-30 Automatic/Manual Intercom
Operating Procedure (cont’d)
To bridge into a Manual INTERCOM call: 
1. When two stations are engaged in an INTERCOM call, a third station, belonging to the same INTERCOM
group, will press the MICM key and go off-hook. 
2. A three-party conference is established. The called stations may hear a Warning Tone when the station
bridges into the call. This Warning Tone is preassigned in System Data.
Use...